Find a Solar Panel Installer you can trust near you.

Solar thermal panels work by capturing heat directly from the sun and using it to heat water. This hot water is then passed through a coil to heat the water for your central heating system. Solar thermal systems are compatible with many existing conventional boilers with hot water tanks, and can be set up to feed in to your existing heating system.

1. After the installer’s measured up, given you an estimated output and recommended some systems for you, they’ll arrange date to come to your home to install the solar thermal panels. They’ll also let you know if any scaffolding will be required.
2. Next, they will start to fit the panels, or collectors, to your roof. Stainless steel brackets will be provided with the system and they will remove your roof tiles or slates to attach the brackets to the rafters. They’ll then replace the tiles and add waterproof flashing to ensure you don’t get any roof leaks, and add the frame.
3. If you’ve chosen evacuated tube solar thermal panels, the installer will bolt the heat transfer unit to the top of the frame but not install the tubes until nearer the end. This is because the tubes start to transfer heat to the exchanger immediately, and when everything is unconnected this could damage the unit.
4. If you don’t need a new boiler with your installation, a new dual coil water cylinder, pump and system control system will be fitted. It’s best in a loft or upper floor of your home.
5. A new thermal store or hot water tank that will store the heat provided by the solar system is much larger than a standard tank but it may fit in the spot of your old one. The installer will ensure that it’s connected to the mains cold water, your other heating source (such as a gas boiler or biomass boiler), immersion heater, temperature sensors and the solar collectors themselves.
6. Next they will install the pumping station, usually near the water tank. The expansion tank will be installed on the solar thermal loop, which is usually nearby. Its job is to prevent pressure changes that could damage the system.
7. You’ll get a heat generation meter which must be MCS-certified if you want to take advantage of the RHI, and any control equipment that comes with the system will be installed.
8. The installers will then bring the system to pressure by pumping the heat transfer liquid into the system up to a pressure of around 2 bar.
9. Finally, your MCS-registered installer will register your solar thermal system so you can apply for RHI payments of up to £525 per year.
So that’s the process of installing solar thermal panels. Remember – it's always best to use a professional to install any kind of renewable technology.

After making the very important business decision to go solar, you may also want to know just how long it’ll take to complete the installation process and start generating electricity. After all, generating electricity is the main reason you made the switch to solar system. In this post, we’re going to provide you with in depth details on how long it takes to install solar panels as well as the factors that may affect that time.

The entire process of solar panels installation and getting them approved isn’t an overnight process. You’ll have to wait for periods for each step of the process whereby one must be completed before moving to the next. The time required to complete each step can, however, vary largely depending on your location, the type of solar panels you opt for, the solar company you hire as well as the number of people that’ll be making the installation. Here are the steps to a solar system installation and the estimated time each are expected to take:

• Site assessment. Once you chosen your solar company, the first step would be to have a solar professional from the company to visit the site to examine the roof and other features so as to make sure that they’re able to support a solar system. From the initial contact to scheduling the site visit, this step can take up to 1 to 2 weeks
• Local permitting. This involves getting the right permits from your local authorities. This can take up to 3 to 6 or more weeks.
• Solar system design. This may take up to a week or two depending on whether or not you need design approval and also where the parts are coming from
• Installation. This step can take a week or two depending on the size af your solar panel and roof.
• Inspection. This step can take up to a week depending on where you reside and how quickly the inspector can visit.
• Utility connection. Depending on your utility company, this step can take up to 2 weeks.

Are you currently weighting the possibilities of adding a solar system to your commercial building? With lots of commercial property owners in the UK using solar now, many more are gradually coming to terms with the numerous benefits they stand to derive by getting one. Therefore, if you’re thinking about adding the system to your commercial building but do not know where to start, you’ve come to the right place.

In this post, our aim is to help you calculate the number of solar panels you’ll need to power your entire commercial building. Starting from the panels, you can begin by taking into account everything that makes use of power in your commercial building to get a good idea of how many you’ll need.

• To get started, you’ll have to determine the number of watts used by your commercial building. To get this, you simply have to go through your utility bill for kilowatt-hours (kWh). This varies amongst buildings and being able to identify your daily average energy usage will assist you in getting your solar panel needs.
• Once done, you’ll also have to determine the peak sunlight hours - having in mind that the solar panels only work when under direct sunlight. Once determined, you can then multiply the figure in hours by your home’s hourly energy usage and divide by your selected solar panel’s wattage.

In general, a medium-sized commercial building making use of an average amount of electricity will require about 70 average quality solar panels so as to cover its entire electricity needs. These are, however, just averages, so yours could be more or less so getting the idea is vital here.

Solar panels are made up of photovoltaic (PV) cells. These cells are made from silicon semiconductors, which absorb sunlight and convert it into electricity.

There are three main types of PV cell: monocrystalline solar cells, polycrystalline solar cells, and thin film solar cells. Monocrystalline cells are usually the most efficient and expensive, and thin film solar cells are the cheapest and least efficient. These are all made from silicone, but are manufactured in different ways.

When you’re about to transform from the standard electricity to solar energy, what determines your solar system’s size is the amount of solar that’s required. The amount of solar that you’ll need, on the other hand, requires considering the end goal, be it to increase money savings, reduce environmental contamination, maximize Returns On Investment ( ROI), or just to copy what the neighbour’s done.

In order the determine the number of solar panels that is needed, the first step would be to calculate the number of kWhs that’s currently being used. A kWh is what’s used to determine the amount of energy that has been incorporated over time which the utility uses to bill you. What’s strongly recommended to create a suitable range is a 6 to 12 months average of your household electricity bill. Other factors that can play a key role in the determination of the number of solar panel needed include the following:

✓ Sunlight exposure hours. In order to know just how much energy your solar panels will generate, there’s a need to know the number of direct sunlight hours you should expect on a daily basis. For example if you stay in a region that’s usually very sunny, then it’ll be reasonable to expect more energy production per panel than regions that are usually cloudy.

✓ Angle and size of the roof. Roofs with a lot of workable space may require to let go of some efficiency opting for larger and cost effective panels to achieve the targeted energy. However not all homeowners have sufficient roof space or shade coverage for the solar panel they actually want. Also, the degree at which the roof slants will also determine if the sunlight is hitting the panels well enough and the amount of energy that can be generated thereof.

How To Install Solar Panels And Batteries

Have you decide to purchase a solar system for your home and wondering how to go about the installation? If yes, then we’ve got you covered! In recent times, it’ll be totally safe to say that solar panels and batteries for home use in the UK has now become more of a necessity than a luxury considering the numerous benefits the system offers. However, with the cost of having the system installed, you might be forced to think about the doing the installation yourself.

If you lack proper training and experience in the solar system installation process, it’s advisable to hire the services of a qualified technician who can guarantee the best results the first time and help you save time and extra costs that may result from possible costly errors. Here, we’ll give you a good insight into the installation process.

• Mount the solar panel and ensure it’s properly screwed to your roof. Try to position in such a way that it faces direct sun rays to have enough solar power generated.

• Connect your charge controller. The current that’s being generated by the solar panels will not be stable all day long. As a result, it’s important to avoid connecting solar photo voltaic modules directly to your better, if you don’t want it damaged. To control the current received from the solar panels, the charge controller is required. It has three connecting points - one for the battery, one for the solar panels and the last for Direct Current (DC) identify the one for solar panels and connect accordingly.

• Connect the battery to charge controller. The charge controller possess two terminals for the battery - the positive and negative terminals. Connect the positive terminal to the positive of the battery and also do the same for the negative.