Find a Shop Fitter you can trust in Southam.

Commercial architects can produce plans and technical drawings as well as offering advice and assistance to help you achieve your desired goal. They will also put a creative spin on your building project – perfect for retail or office buildings. Commercial architects will make your building stand out from the crowd!

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

Installing your Nest thermostat may not be as easy as screwing a light bulb, but we can also assure you that it isn’t very difficult either. However, if you lack the needed training or experience to pull it off, we’d recommend you hire the services of a professional in order to save yourself some time and money. This guide will give you some quick and easy steps to follow and ensure you make no errors during the installation process.

Once installed removing the Nest Thermostat can be done. To get started, you’ll need just a Philips head screwdriver which Nest has thoughtfully provided with the device.

• Turn off the Nest Thermostat by switching the circuit breaker to the off position.

• Label or mark your old thermostat’s wires. However, if you notice your thermostat is tagged 120v or 240v, or possesses thick wires, do not connect the wires to the Nest as you have a high voltage system.

• Uninstall the old thermostat by locating detaching the wires coming out from the wall into the thermostat. Once done, simply unscrew the device from the wall

• Mark the spot of your thermostat. Do this by threading wires through the Nest base plate’s centre incorporate the tiny bubble level. Once done, you can then use a pencil to mark te two screw holes.

• Attach the trim plate. If you wish to cover the screw holes, simply install the trim plate in the Nest box’s bottom to the base plate.

• Using the screws and screwdriver, attach the Nest base to the wall.

• Connect the wires to the Nest by putting the labelled wires in the Nest’s corresponding ports.

• Put the Nest display by lining up the connector on the display’s back.

• Turn on the power by switching the circuit breaker to the on position

• Connect your Nest thermostat to the WiFi network.

• Follow the on-screen guide and set the temperature.

• Use your smartphone or tablet to download the Nest thermostat’s mobile app to monitor and control your device remotely.

This is one of the most important factors to consider when considering the replacement of your old garage door. However, the replacement cost of a garage door relies on a number of factors such as the type of the preferred garage door, the size of the area in which the door will be installed and lots more. To get a more accurate estimate of the replacement cost you also have to consider the cost of removing the old garage door and the mechanism, the price of disposing the old garage door from the premise, the cost of installing a new sub frame and a new door panel, cost of the new operating mechanism and modern locking installation as well as the cost of purchasing and installing the new garage door. Here, we are only going to look at the purchase and installation cost of the new asset.

Today, there are a wide range of garage doors to choose from such as sectional, rollers, up and down, side sliding ( round the corner) and side hinged. They also come with varying materials which plays a significant role in the cost of the item such as steel, timber, aluminium, PVC and more. Furthermore, several garage doors include the option of being controlled electronically.

Generally, garage doors will cost between £300 to £5000, and include a price with the range of £150 to £1000 for the ones that can be operated electronically. With that in mind, the remaining cost would be that of the professional installer and that should be between £150 to £250 a person per day. For the labour, you can expect the installation of your new garage door to be completed within 3 to 6 hours (although an electric or specialist door may take longer installation time than the conventional or manual ones).

How To Tile A Bathroom Wall

Tiling your bathroom walls will not only increase the visual appeal of your space, but also provide an additional layer which helps protect against potential moisture damage, moist growth and also makes the bathroom a lot easier to clean up. So if you’re are looking to tile your bathroom, it’s recommended to get in touch with a skilled professional to ensure you get the best results. However, this guide will provide you with a good insight on how to get through the process smoothly and avoid costly errors. Let’s take a look!

lPrepare The Wall’s Surface

• Make sure that the surface is clean, smooth and dry.

• If there are any dips or holes, ensure to have them patched or sanded.

• Measure the area to be tiled and shape the backer board to fit, if a new wall surface is necessary.

• Cover the new surface area with adhesive to attach the back board to the surface.

lMix The Mortar

• Firstly determine the tile layout and make a layout tool

• Install the datum

• Follow the instructions of the adhesive package as the type you’re to use depends on the wall type.

• Create a consistent and smooth paste by mixing the adhesive with water.

lInstall The Tiles

• Using a notched trowel, spread the mortar.

• Put a thin layer at the back of each tile and press it against the surface.

• Create ridges using the notched side of the trowel.

• Clear out any excess adhesive on the tile’s surface as you continue.

• Put the spacers at the joints

• Remove the datum planks when ready to install the outer edge tiles.

lApply The Grout

• Put the grout over te tiles with a grout float

• Clean out excess grout with a damp sponge

• Seal the tiles once the grout is dried

Installing solar panels for your business operations can provide you with a number of impressive benefits. It is not only capable of helping you minimize your business’ environmental footprint but it can also go a long way to help you save money. Irrespective of your company’s size, whether big or small, it can still benefit immensely by making use of solar panels. If you’re currently planning to install solar panels in your business environment, then you’d probably want to know just how much it’ll cost to complete the project. In this post, we aim to give you a good insight into commercial solar panel pricing so as to help you make the best informed decisions possible . Let’s take a look!

In truth, there’s no single and accurate answer to this question as there are a number of factors that can influence the cost of commercial solar panels. These factors include the size of the roof, the amount of energy that’s generated as well as the number incorporated. To give you a general idea, the price of solar panels for commercial property is usually within the range of £16000 to £70000 for small to mid-sized companies. For a more accurate estimate, you’ll need to get in touch with a professional with your unique needs.

There is also a need to evaluate the cost of solar panels so as to determine whether or not they’re a feasible option for your business. In order to determine the amount of energy your company uses per month, simply take a closer look at your utility bill.  This should indicate just how much energy you use per month as well as how much the utility company charges per kW. In general, most small to medium sized companies will incorporate 30,000 to 50,000 kWh annually and you can expect the cost to differ based on your location and the size of your system. The rule of thumb with larger systems is to calculate using £1000 per kW, plus VAT as the yardstick.

Lean-to conservatories are often known as Mediterranean conservatories or sunrooms and are a great way to add more living space when you’ve only got a small amount of room to work with. They usually have clean lines, a rectangular shape and attach to the side or rear of your home, which makes them one of the easiest conservatory types to build yourself.

So how do you build a wooden lean-to conservatory? The first step is to decide what you want it to look like. Most lean-to conservatories are constructed of glass and the wood frame, but you can choose to have dwarf walls too. Dwarf walls are low brick walls that are useful if you’re planning to plumb in radiators, have air conditioning installed or put plug sockets in the conservatory.

When you’ve decided what your wooden lean-to conservatory is going to look like, you’ll need to get the materials. You’ll need to choose a hardy wood – oak is the most expensive but also the most durable – and source glass for the windows. You’ll also need to decide on a roof material and work out the correct pitch.

The first step to building your wooden lean-to conservatory is to dig the foundations. You’ll then need to level the earth, then add concrete to the correct height, which should be lower than your property’s existing damp course. Then, you’ll build up to the damp course, which will be your conservatory’s floor level. Don’t forget to make sure it’s even.

If you’re building a dwarf wall, start it from the base and build up to no more than 1 metre high. Once the cement is dry, place external sills on top of the dwarf wall. You’ll then need to secure the frames; start with the one that secures to your property, then do the same for the rest, connecting outwards until they meet from the two sides. Then put up your doors.

Now it’s time to build the roof. This should be simple if you’ve bought your own custom-made kit. Place the roof ridge on top of the frames, then add the roof rafters between the roof ridge and hip bars. Fit your glazing sheets and guttering – it’s important that your wooden conservatory roof has guttering just like your house, otherwise your conservatory roof won’t last very long and could even cause rainwater to rot your wooden frames.

Once you’ve built your wooden lean-to conservatory, all that’s left is to decide on how you want to decorate it. But if this all sounds like too much, get in touch with specialist wooden conservatory installers who will be able to give you a quote for building you a lean-to conservatory.

If you’d like to hire a residential architect, but have limited funds, there are several things you can try to reduce their quote.

Firstly, you don’t necessarily need to hire them for project management – you could just ask them to do the design. This will mean you’ll have to do some extra donkey work, but you could choose between finding a cheaper professional to do your project management or simply doing it yourself.

There might also be other architectural services that you can cut down on. Some professionals offer extras like landscape, interior and detailed joinery design. If you can do without any of these, this will help to reduce the overall cost.

You could also think about scaling down your project. Lots of residential architects work out their fees as a percentage of the total construction cost of your project. Lower the cost of this, and your fees might go down too.