Find a Shop Fitter you can trust in Uttoxeter.

Presenting with its unique sets of components, the price for every house renovation project varies considerably. Though giving a proper price for the house renovation is not possible, you can generally expect to pay anything between £40,000 and £75,000 for renovating a three-bedroom house.

You must list out all the changes needed since renovation comes with several potential costs. This makes it easier for you to calculate the renovation costs and start planning your budget accordingly.

Let us take a look at some of the crucial factors that affect the cost of renovating a house

• Property size

• Property’s condition and age

• Complexity oof the job

• Structural work

• Building extension work

• The quality of materials, fixtures and finishing

• Decoration

• Location

When it comes to renovating a three-bedroom house, the average cost is around £ 57,000. A new gas supply will cost you around £1,500, depending on the route of the supply. There may other additional costs involved if you are looking to do any work to extend the gas supply line.

The cost of rewiring a house is in the region of £5,750. That price will also be dependent on the complexity of the electrical systems in your house and the size. If you are looking at installing a new set of windows, it can cost you up to £6,000, with the average cost being about £4,250. Replastering walls will add another £2500 to the total budget. A new kitchen will set you back around £7,000, on average including the cost of design, materials and installation. Most renovations will need a new bathroom. Installing a new bathroom will cost you around £4,250.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

Two of the commonly used terms in the UK and Irish construction industry is “First Fix and “Second Fix First fix encompasses all the work required to take a building from foundation to stroking plaster on the interior walls. This comprises of building walls, floors and ceilings, and implanting cables for electrical supply and pipes for water supply.

Some claim that First Fix starts after the shell of the building is complete, and ends when the walls are plastered. Some of the elements in the first fix are as follows.

• Drain runs: must be downhill and straight

• Spare conduits: drawstrings

• Soil pipes

• Copper pipes

• Normal pipes

• Doorbell

• Door frames

• Pocket doorframes

• Stairwell

• MVHR (mechanical heat recovery ventilation runs)

• Push-fit or other plastic piping

• Electrical back boxes

• Electricity cable runs

• Telephone, data and audio-visual cables

• Socket location

• Security

• Fire alarm

• Sound insulation

• Plasterboarding

It is to be kept in mind that the list goes on as there are several things that you can do when you are building a house from scratch and it is impossible to cover each and every aspect in detail.

The second fix includes all the work after the plastering of a complete house. These include linking cables to the electrical fittings, coupling pipes to the baths and sinks and fitting doors into doorframes. Second fix work requires a tidier finish than the first fix.

Carpenters, electricians and plumbers get a proper idea on the division of work. They will also be able to visit the construction site at different times.

Project managers can simply report it as the "first fix complete" or "the second fix 50% done" and others would very easily understand.

Regardless of the fact that a construction company might specialise in a certain form of fix, be it the first or the second, they are obligated to have a rudimentary understanding of both and are required to perform them from time to time.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

• Firstly, you need to put the plasterboard sheet flat on a firm surface.

• Use the tape measurement to measure the cut you wish to make.

• With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

• Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

• Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

• The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

• Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

• Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

• Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

Asbestos is very dangerous if inhaled. It can cause a variety of lung-related diseases. Asbestos will generally not be released into the air unless it is disturbed. You should be very careful if you suspect there may be asbestos in your home and have a survey carried out to check that it is not being released into the air.

If you are considering building a wooden conservatory in your home, it’s normal to be curious about whether or not the home improvement effort is costly. Basically, wooden conservatories are ones that have been constructed using a wooden structure. There are options to choose from which timber and this can also play a part in the amount you’ll have to pay. Conservatories using hardwood, which are more durable and requires less preparation, are also considerably costlier than the softwood counterpart.

For just the timber in a kit build your own conservatory you would be looking at around £10,000 to £20,000. Generally, a wooden conservatory built for you will cost you a range between £20,000 to £50,000 based on the type of wood, the size as well as the style you opt for.

In addition, wooden conservatory prices are also determined by the supplier you’re dealing with. As a result, it’s advisable to conduct a proper and detailed market research about the available suppliers and identify the one who truly offers quality materials at an affordable rate. If you wish to go for an Oak frame, the price will typically be higher.

To give your house a more traditional look, you can go for a timber conservatory rather than a uPVC one. However, it requires more maintenance than the uPVC as well as regular weatherproofing to prevent it from warping or rotting as a result of changes in humidity or temperature. If you want the timber look there are options with modern uPVC which can give a similar style but at a lower cost.

It can be quite tricky knowing the right time to purchase and fit an air conditioning system, however if you get the timing right, this can go a long way to help you save both time and money. It’s important to note that different individuals usually have varying needs - like it it’s possible your existing unit just broke down during the summer months or you’re carrying out some renovations during spring.

In general, there’s the need to put a couple of factors into consideration in order to make sure you AC installation is a hassle free experience. The best time to install an air conditioner is actually before the construction of the house. Several high set homes do not possess the space to fit fully ducted air after building. And even if there’s space, accessing the ceiling and down into the floors can be pretty expensive and difficult.

Installing an air conditioning unit earlier would mean less plaster would be required later down the road. A good air conditioning installer or HVAC expert should also advice you on the best location for the unit in order to help you maximize cooling in the summer and heating in the winter. Most importantly, if your AC unit is built into your house’s design, you’ll be able to save more money in the long run. However, you may not be able to fit a unit when constructing or renovation, therefore choosing the right time would be a question of, when is the right time of the year.

Generally, choosing a month in the off-season is actually a much better time to fit an air conditioner, but ensure that it’s the right time. Overall, the best time for an air conditioning unit installation is autumn when the demand is at its lowest. Since retailers are usually overstocked with units after the summer months, you can get yourself some nice discounts