Find a Shop Fitter you can trust in Perth.

Gravel, asphalt, concrete and paving can all be permeable. However, some types of asphalt and concrete are impermeable. This is why it’s important to be precise about what material you want for your driveway. If you want a permeable driveway, you should also make sure that your sub-base is also permeable.

Once you have your new bathroom installed, or perhaps you’re only replacing the old downlights, you’d probably want to know how to go about fitting your new bathroom downlights. If yes, then you’re not alone! This is a very common question amongst several homeowners and we wish to guide you through once and for all. However, it must be said that if you are not a competent DIYer or probably lack the confidence or skills to pull this off, then it’s advisable to hire a professional to get the best results and also save yourself some money and time.

Here are the list of the tools you’ll need to fit your bathroom downlights: Tape measure, chalk line or laser, pencil, pad saw, hand drill, hole saw and screw drivers.

✓ Measure the bathroom ceiling and mark out the central point of the light which will be where the downlights will be placed. Drill a small pilot hole here.

✓ Check above the ceiling to ensure that there’s no pipes, joists or wires in the way. It’s always a good practice to make sure that there’s sufficient room around where the downlight is to be installed in order to avoid placing it too close to a joist or any other obstacle. You should try as much as possible to maintain a 6 inch gap around the spot where the downlight is placed to make sure the fitting does not overheat.

✓ Use a hole saw or a plasterboard saw to make the cut out for the downlight. Check the downlight’s box for instruction on the size.

✓ Once you’ve been able to make a clean cut ceiling hole, pull through the wiring through the hole so that the downlight can be wired. Once done, then you can fit the downlight into the hole by holding the two springs back against the sides of the downlighter and push up into the hole.

One of the major source of concern for several home and property owners in London when it comes to heating and cooling systems is whether its really necessary to use an air conditioning system throughout the year or just a couple of months a year. Well, if you’re also worried about the this, then you’ve come to the right place. In this post, we’re going to consider why making use of an air conditioning system is essential all-year round. Let’s take a look!

The short and simple answer to this question is, it depends. However, if you really want to have a total control over your own comfort at home, then the answer is yes. In fact, most individuals who have installed heating and cooling systems with the intention of only using it in July and August usually find themselves making use of it all through the year and having a more sound sleep than ever before. What’s more? London is known to have uncomfortable and inconsistent temperatures all year long. If you intend to use your system for a specified couple of months, you may just be shocked to discover when you’ll need it the most may be outside your selected usage period.

In a move to protect older properties or an apartment complex, most landlords in London usually won’t give permission to enable structural changes. As a result, this has given several Londoners the impression that they’ll have to just cope with the heat and cold all throughout the year. In this kind of situation, all that’s needed is the installation of internal air conditioning units which does not need any penetration through the exterior wall to be fitted.

Driveway work is usually done in the warmer half of the year. This is partly to avoid bad weather. If you want to get ahead and avoid waiting for a contractor to be free, you should try getting in touch with a professional in the early spring so a date can be booked for install as soon as practically possible.

Central air conditioning system is a system which operates by cooling air at a central place and distributes the cooled air to and from rooms with the help of one or more fans and ductwork. What makes the whole idea of air conditioning feasible is the operations of the air conditioner compressor. When it cooling gas is compressed, it allows it to absorb heat from the house and blows it outside into the outside air and that’s exactly how the cool air is being generated.

Central air conditioning are of two main types which includes a split system as well as a packaged unit.

Generally, in the split system AC unit, both the condenser and compressor are included in the outdoor metal cabinet, whereas the indoor cabinet includes the evaporator. Typically, in several split system air conditioning units, the indoor cabinet will also include an air handler or a furnace. What’s more? The evaporator coil of the AC unit is fitted in the cabinet or the furnace or heat pump’s primary supply duct. This type of central air condition is usually the most economical AC unit to fit if you already have a furnace in your home.

However, in a packaged central air conditioning system, the components including condenser, compressor and evaporator are all included in one cabinet. Supply of air as well as the return ducts are connected through the home’s exterior wall or roof to the package central air conditioning system - mostly placed outdoors. This type of central air conditioners also features electric heating oil or a natural gas furnace. With this perfect blend of central heater with air conditioner, there’s simply no need to a separate furnace indoors.

How To Install A Septic Tank

If you’re planning to get a new septic tank system or replace the existing one, you’d probably want to know if it’s a task you can do all by yourself especially if you happen to be a competent DIYer. However, unless you’re a heavy equipment operator, installation of a septic tank system is by no means a DIY project. And even if you have the heavy machine at your disposal and you know quite well how to use it, you’re still going to need the guidance of professionals.

You’re going to need the services of a soil expert to evaluate the site, a plumbing contractor to fit and connect pipes, an engineer to design a good system and more. You may want to be involved in all these but local health authorities requires that a licensed personnel should be in charge. In this article, however, you’ll discover the septic tank system installation process.

To install a traditional septic tank system, you’ll have to start by digging a hole for the tank following strictly the instructions provided on your approved plan by the local authorities. Do not drop the tank into the hole after digging, you’ll need to connect it to the building sewer with 3 or 4 inch waste pipe which should be at a minimum slope towards the tank. Then, extend a drain pipe from the other end of a tank to a the distribution box on the drain field.

Once completed, dig several parallel trenches of this box extension across the drain field. Put in a layer of gravel along with 3 to 4 inch perforated pipes in individual trench and connect the pipes with the distribution box and cover them once done.

How Long Does A Gas Safety Certificate Last?

As a result of faulty installation and irregular maintenance of gas appliances and chimneys, a lot of people have been met with an untimely death caused by the toxic gas - carbon monoxide. This is a gas that’s completely odourless, colourless and tasteless - meaning you can’t identify one of its in the environment. But what you should know is, if you stay in an environment filled with carbon monoxide, you’d probably be dead within a couple of hours. Consequently as a landlord, you must do what’s best to ensure the safety of all your tenants by making sure that all your gas appliances and chimneys are subjected to annual check by an approved Gas Safe engineer as required by the law.

Wondering how long a Gas Safety Check will take? The safety of your gas is guaranteed by carrying out regular examinations. Whether or not you possess a gas alarm, it’s still vital to conduct regular gas safe checks to make sure your home is safe. A typical gas safe check would last between 30 to 60 minutes for a normal domestic property. However, in the situations whereby a need for repair arises, it may take longer time to complete. Other factors that can also affect the timing includes includes both the size and location of your property.

So how long does a gas safety certificate last? The simple answer to this question is 12 months. If you own a rental property in the UK, it’s up to you to ensure all your gas appliances and chimney is check after every 12 months to obtain a Gas Safety Certificate which you should hand out a copy to all tenants living in your property. However, if you don’t own the property, you can inform your landlord to get one as soon as possible while also providing a carbon monoxide alarm.

The more you’re at home during the day, the more you can save on your electricity bill, since solar panels generate electricity during the day. The Feed-in Tariff scheme (FITs) ended in March 2019, but the new Smart Export Guarantee (SEG) pays you, via your energy supplier, for the electricity you export back to the grid. With the savings involved in generating your own electricity and SEG payments, you can expect to save up to £390 per year on your electricity bill.