Find a Shop Fitter you can trust in Riding Mill.

How To Clean Roof Tiles?

If you’re a DIY person with a dirty roof tiles or just a homeowner who’s also a lover of knowledge, you may probably like to know how you can have your roof tiles cleaned. This is a very common question which often depends on the dirt or debris you’re dealing with as well as the type of roof you possess. Most often than not, if you own a traditional concrete or slate roof tiles, then you’re more likely to battle moss and or algae growth.

If you’re not a competent DIY person or do not have enough confidence to pull this off, then it’s advisable to hire the services of a professional who can guarantee the best results for help. In this article, you’ll learn how to go about cleaning your roof tiles. Let’s have a look!

✓ Consider Safety. When it comes to roof cleaning, you have to be very careful. They’re normally high up and any task that deals with height will usually require putting safety measures in place. Firstly, it’s important to be confident with heights and ladders, if not you’d have to find someone who is. And if you’re confident, there’s also the need to find someone who can help you hold the base of the ladder.

✓ Trim the trees. Nearby trees are usually a threat to any roof and also makes cleaning much harder. So it’s always wise to cut any overhanging branches before you proceed.

✓ Bleach or not to bleach. Although you have to be very careful using beach and water but it also happens to be one of the easiest DIY ways to clean your roof. You either stand about 4 feet away and rely on water pressure or clean down the tiles by hand.

✓ Try not to make use of a blaster.

If you’re going through new constructions or renovations and looking to change your old front door and install a brand new composite door, then you’re at the right place. Composite door fitting can be a DIY project but it’s essential to have the necessary training and experience before commencement. If not, we’d recommend you hire the services of a reliable professional to guarantee the best results and save yourself some time and money.Here, we’ll give a good insight into the composite door fitting process.

To get started, here are some of the tools that may be required - tape measure, hammer, stanley knife, crowbar, chisel, saw. Silicone sealant gun, spirit levels, electric drill ( including the hammer section), rubber mallet and 6mm socket spanner.

lPreparation

• Remove the existing door by rounding up the door frame firstly with a knife to reduce the possible damage to the wall.

• Cut through the door jambs.

• Remove each in two separate sections.

• Ensure the opening is level without any screws, mastic and filler.

lAlign Your Composite Door

• Ensure the sill of the door is level and flat.

• Make sure the frame is square and plumb in both planes.

• Bridge the cavity of the wall and cover the DPC

• Ensure that the frame is square. If not, your composite door won’t function as it should.

lInstall Your Composite Door

• Place the door in the frame.

• Hold the frame firmly in position with wedge packers

• Make sure the packers are positioned close to where the fixing will be placed.

• Make sure the jams are square and plumb in all planes by using a long spirit level.

• Secure the frame to the brickwork with the use of a drill.

• Place the fixings at the top and bottom of each hinge as well as each of the lock keep.

• Top fixings should be fitted 150mm and 250mm from each corner.

A Structural Engineer is quite likely to be a participant of the ICE (Institution of Civil Engineers) or a registered member of IStructE (Institution of Structural Engineers) and also will probably have after his or her name the letters MIStructE, FIStructE, MICE or FICE. Structural Engineers with these letters after their names are referred to as Chartered Engineers.

It is usually encouraged that you involve the services of a Chartered Engineer as opposed to an Engineer that is not chartered but it should be noted that there are some Engineers with significant experience who are not chartered. The choice is yours.

Most responsible contractors will dispose of the old fencing via an approved commercial waste site. Do check that the cost of taking rubbish away is included in the quotes you receive, otherwise you might find you get stung when it comes to paying for the work.

How much a flat roof costs to repair depends on a few factors. Is your flat roof on a garage or an extension? What is the flat roof made from? It’s always best to get a few quotes to compare prices, but we’ll give you a rough idea here. If your flat roof was installed in the 1990s or earlier, it’s likely that you’ll see some leaks or damage soon. Felt flat roofs used to be installed completely flat, which meant that water couldn’t run off. That means that water pools and can create moss and damp. Sun exposure can also damage the felt, causing damage and eventually holes that lead to leaks. If you’re lucky enough to have got away with just needing a flat roof repair, this should set you back an average of £100 per square metre. If your roof is sagging due to the weight of it putting pressure on the timber frame, you might need additional joists – which could cost anywhere between £1,000 and £2,000, depending on how many you need. But if the problem is due to the internal part of the roof system becoming waterlogged, you could be looking at over £5,000. If your roof is severely leaking or the timber joists are rotting, it might be more cost effective to replace your flat roof. If you keep forking out for repairs, it will eventually be cheaper just to replace the whole thing, which could cost around £2,000.

A skip is a very convenient and great means of disposing the unwanted waste and rubbish in your home. When you kick start your home or garden clear out or clean, you’d discover you have a wide range of wastes to get rid of. However before the commencement of such a task, it is essential to understand that there are particular wastes that are not allowed to be put inside a skip for several reasons by the relevant authorities. There are a handful of regulations that determines what goes into a skip and what cannot. And somewhat interestingly, this may differ depending on the skip company you recruit.

With the presence of an array of skip hire companies in the market today, there are several that can allow almost all types of wastes in the skip. However, some of the most common wastes that can be placed inside a skip includes the following:

• Broken furniture pieces

• Plastics ( because they can be easily recycled)

• Solidified paints

• Furnishings and non electrical fittingd

• Uncontaminated soil

• Cardboard and plastic packaging items

• Metal

• Branches and leaves

• Bricks, wood and rubble

It is advisable to ask your skip hire company what you can put in the skip and what you’re not allowed to put in the skip before moving forward. The guidelines can vary from a company to the other and as a result, there is the need to conduct a proper consultation with a skip hire company to help erase or confirm the fears you might have about your unwanted waste or rubbish. This is to ensure the company selected perfectly matches your proper waste disposal needs. When you’re able to select a reliable skip hire company, all your unwanted waste disposal worries would be completely obliterated. Click here to learn more about skips.

Many examples of asbestos will not need removing, for example if it is present in artex that is in good condition. However, if you are carrying out building work on or near the asbestos it should be carefully removed before the building work starts to make sure it is not accidentally disturbed.

Are you considering extending your living space into a visually appealing orangery? However, before you go ahead with the project, you may want to know exactly what you’re getting yourself into. It is rather important to let you know calling on a seasoned professional for help when it comes to building an orangery is the best bet especially if you lack proper training or experience. This way, you get to avoid costly errors while also saving yourself some time and money. Here, we’ll give you the needed information on how to go about building an orangery.

• Orangery Planning

This is, perhaps, the most important step when it comes to orangery building. There is a need to conduct a proper planning to ensure everything goes right and exactly the way you want it. The first thing to do is to perform the required planning permission checks to determine whether or not your orangery covered under the “permitted development. In some areas, there may be some strict restrictions as the structure’s size. So you just might want to consult your local planning development before taking any step forward.

You can contact any architect for help with the acquisition of the right planning permission. While doing this, also have it in mind that your plans will need to be approved before you can proceed. Once done, it can be very challenge to alter the plans without extra delays or additional costs.

• Construction of Orangery

Do you have any builder in mind? If yes, make sure you inform your architect to be sure he’s happy to work with them. The selected builder will take your plan and build the orangery to your taste as given in the plan. The fitter will put the doors and windows in place as well as the roof lantern.