Find a Shop Fitter you can trust in Northampton.

Choose an architect whose design vision fits with yours – but make sure they’ve got something new to bring to the table. Also check them out to see what projects they have previously undertaken. Ask them. Communication is vital. Pick a commercial architect who can communicate well with everybody involved in the project.

1. Calculate the surface area for your decking Multiply the length (L) of your decking area by the width (W): L x W = Decking Surface Area (DSA) in m² 10 x 6 = 60m²
2. Work out the coverage of your deck boards Add your deck board width (DBW) to the expansion gap length (EGL), then add the deck board length (DBL) to the expansion gap width (EGW). Then multiply these numbers. (DBW + EGL) x (DBL + EGW) = Single Board Coverage (SBC) 0.144m + 0.005m = 0.149m 2.4m + 0.003m = 2.403m 0.149 x 2.403 = 0.358m²
3. Calculate the number of deck boards you need Multiply the SBC by 1.1 to allow for 10% wastage. Then, divide the DSA by the SBC. DSA / SCB x 1.1 = Total number of boards required 60m² / 0.358m² x 1.1 = 184.36 boards – so round up to 185 so you’re not left short.

Though it's hard to maintain woodworm out totally, you can certainly make your home less enticing by:

Keeping all timber completely dry - The wetter wood ends up being, the less complicated it will be for larvae to bore with as well as stay in. Women timber beetles wish to give their offspring the best opportunity of survival so will certainly pick a wooden surface with this in mind.

Keeping your residence warmed and well ventilated - Home heating your house to an appropriate temperature while keeping it ventilated will minimize the possibility of moisture accumulation as well as saturation of wood.

Getting furniture made from good quality hardwood - Hardwood is understood for being most resistant to woodworm invasion due to its thickness and lack of nutrients for woodworm larvae to live off.

Sealing timber with varnish - Varnish makes it harder for wood uninteresting pests to pass through a wood surface area. It is also toxic. Attempt to re-varnish or seal any surfaces that have actually deteriorated in time.

Very carefully looking for indications of woodworm when purchasing antique or used furnishings - Always inspect that you are not bringing anything infested right into your house, checking for the tell-tale indicators defined over.

Eliminating contaminated wood from your house - If you learn that a piece of lumber is infested, remove it simultaneously preferably.

Changing infected timbers - Once contaminated hardwood has actually been removed, make certain to replace it with brand-new lumber that is appropriately prepared with a protective surface and also dealt with.

Deal with the wood with a woodworm treatment - take the aggressive action to avoid problem as well as deal with hardwood with a woodworm awesome.

Using flytraps - Flytraps can be made use of in a preventative technique to catch and also consist of adult timber uninteresting beetles prior to they have a possibility to mate.

Ad hoc visits from your engineer to fix small issues with your heating system may actually seem cheaper and a lot more affordable, however when a boiler is ripe enough for a change these small issues are always never ending. Over some period of time, these small issues will inevitably get worse and the idea of “mend and make do will be an absolutely false economy. The best course of action in this sort of event is to find a replacement boiler to install as soon as possible. In this article, we’re going to give you some hints that’ll show you when your boiler needs to be replaced. Now let’s take a look!

✓ Insufficient hot water. Here, you’ll have to check the size of your hot water cylinder. It’s crucial to make sure that your boiler is rightly sized to power your heating as well as hot water circuit in line with your demands. You should always seek the advice of a heating expert who can recommend whether to fix or replace the boiler.

✓ Strange noises. It’s normal for components of the boiler to become worn or damaged over time. Replacing the particular component that’s causing the knocking or rattling may seem cost effective at first but more often than not, the noises usually signal a bigger issue which is likely to build up over time. Hence, it’ll be a lot more logical to replace the boiler itself.

✓ Regular repair of your boiler. It’s essential to have your heating system serviced by a Gas Safe engineer on an annual basis. However, when you have to call them more often than once a year for your yearly maintenance, it may be a wise decision to consider getting a replacement.

✓ Other events whereby you may need a new boiler includes when you can’t get the right temperature in your room, when the radiators don’t heat up as they should, when your boiler leaks and if your boiler still has a pilot light.

In several parts of the UK, air conditioning systems are a must especially in the warmer summer months. Fortunately, if your AC system isn’t functioning the way it’s supposed to, suffers frequent system breakdowns when overworked mostly during the hot summer days or perhaps you’re just tired of just having to manage with window units, the latest air conditioning units offers both features and performance that’s superior to the earlier models. And as you would have expected, each facet comes with a cost.

There are a number of factors that can determine the cost of an air conditioning unit. Out of all these factors, the size of your home happens to be the most significant factor that influences an air conditioning unit’s cost. Air conditioning systems are measured in tons, which is a measure of the amount of heat they’re able to remove from a home within an hour. As a rule of thumb, you’ll require about 1 ton of cooling per 500 to 600 square feet. Unfortunately, the square footage alone can’t be used to determine the tonnage. Other factors that’ll also play a significant role includes the efficiency of your most preferred AC unit, how well the home is insulated as well as the thermal nature of your home. On the average, a new air conditioning system for an average home should be within the range of £1000 to £3000 for a unit as well as the installation costs which can vary largely depending on the condition of your ducts. These figures may seem quite expensive, but when the hot summer days come, you’d be glad to have had one installed in your home.

Chimney liners are a very important component of the chimney, but the fact is most home and property owners either continue to overlook them or aren’t even aware of their existence. This is, however, quite understandable given the fact that they usually last a long period of time – more than 50 years. To ensure that they last that long, the question that arises is, do chimney liners need to be swept and cleaned? The short and simple answer to this question is yes, chimney liners definitely needs to be cleaned on a frequent basis. A chimney liner happens to be an essential part of your chimney. When it’s not cleaned, it tends to accumulate dust, soot and dirt which can give rise to a number of problems you’d rather want to avoid. Chimney liner are able to provide adequate protection to your flue but even at that the water, creosote and other contaminant build up can make the liner to deteriorate, and making it unsafe for usage. In other words, contrary to several belief, chimney liners do need the same amount of cleaning as chimneys without liners. Failure to sweep your chimney liners can give rise to the following problems:

• Creosote buildup. If your main source of fire is wood, then you’ll definitely have creosote present in your chimney. This is highly combustible and its buildup may lead to fire outbreak.
• Carbon monoxide poisoning. Carbon monoxide is said to be on the rise by NCBI and its primarily generated from heating systems which are terribly ventilated as a result of uncleaned or dirty chimneys.

If you’re not an expert floor installer who would take wall tile installation as merely being a vertical floor, you are advised to be very cautious when tackling the project. The installation of wall tiles follow some set of rules which you’d better not break if you really wish to protect your investment. And worst of all, a wall tile done wrong is a lifetime penalty of having to look at it. So how can you get it right? Well, probably by reaching out to a wall tile installation professional for a good quality solution that’ll save you time, money and effort. However, we’ve put together this guide to help give you an insight of how it works and also to help you avoid some unnecessary expenses. Let’s have a look!

• Hang a batten board

✓ Start your rows of tiles or bottom-most course with a batten board which works to prevent spillage of tiles.

✓ Position the batten board at 3/4 of the tiles’ height. Ensure not to start at the floor.

• Form A Pyramid Shape With The Tiles

✓ If you’ve reached the bottom row of tile, then arrange the tile in a pyramid shape. To achieve this, you’d have to install the tiles one through four as instructed. Each following row will be draped over the pyramid.

• Examine The Floor For Level & Walls For Plumb

✓ If your floor level or plumb is off by a maximum of a half-inch over the course of 8 feet, add extra baseboards and trim to cover up the problem.

• The Least Size Of Tiles To Be Used Is Half-Wide

✓ Ensure that no “silvers (tiles that are lower than half the width of the tile in question) are incorporated in the project.

It’s always a good idea to be sure of how you’re going to keep the annoying gravel spillage off your driveway way before its installation, however, if you’ve already done so, it’s better late than never. We all know how great a gravel driveway can look when the gravels manage to stay in place. When gravel is used on a driveway it provides a great transition from the normal hardness of a driveway to the organic softness of the lawn which doesn’t retain water or gush runoff during irrigation or rainfall. Unfortunately, the sad thing here is gravel don’t just like to stay put. Before long, if ignored, you’d realize your hard surfaces will almost be covered with gravel coming in from the side. So what’s the solution to this rather annoying situation?

Here, we’ll show you just how you can keep your gravel in place in your driveway. Let’s take a look!

The solution here is simple - simply make use of Pour On. With Pour On, you won’t have to think about of clearing out your gravel features to put an end to the issue of loose rocks spilling on your hard surfaces. With Pour On, you’ll be able to hold your gravel in place for several years to come. And even more importantly, it’s able to achieve this objective while also protecting the integrity the existing permeability of your driveway. What’s more? It also goes a long way to retain the natural look provided by your gravel driveway which makes it the perfect solution to the annoying gravel spillage issues.