Find a Shop Fitter you can trust in Scarborough.

Asbestos refers to a group of minerals made up of tiny fibres. If you become exposed to these fibres and breathe them in, you’re at risk of contracting a dangerous lung-related disease.

Asbestos is strong and a good insulator, which means it was previously used to insulate and reinforce parts of buildings, like ceilings, roofs and guttering. Its use has been banned in the UK since 2000, but it is still present in lots of domestic and commercial buildings today.

Asbestos usually only poses a health risk if the material it’s contained in is damaged and its fibres are released into the air.

Air source heat pumps work by absorbing heat from the outside air and transferring it inside to heat up your property.

An air source heat pump has an outdoor unit containing a refrigerant. This absorbs heat from the air and passes into a compressor, where the temperature is increased. The heat then transfers either into water, which feeds into your wet heating system, or into air, which is dispersed around your property.

Air source heat pumps need electricity to run, but this is to power the compressor rather than directly generate heat.

Prior to removing artex on your ceiling, it’s always crucial to determine whether or not the surface coating material contains asbestos. Asides from this, you may also wish to know how much you’re going to have the asbestos artex ceiling removed. If yes, then you’ve come to the right place! In order to help you make the best informed decision possible, this post was written to help give you an idea of the price it’s going to cost to remove asbestos artex ceiling in the UK.

Unfortunately, as simple as it seems, there’s no single straightforward answer to this question as there are many factors that can affect the cost of hiring an asbestos artex removal professional. These factors include the project’s scale, the complexity of the area which needs to be removed as well as the need for extra materials. Generally, professional artex removal companies charge a standard rate for their labour. As a result, you can always predict that the tradesperson’s labour will be more costly based on the extent of the job. Therefore, the more costly the labour fees will be if the job takes longer time to complete.

On the average, a tradesperson will charge within the range of £250 to £400 on a daily basis to undertake the project for you. And of course, you can expect these rates to vary based on the company hired as well as the area you live in. For rxample, you can expect that a tradesperson’s charges would be higher in an area such as Central London, as opposed to other areas which are more rural.

Using a designer to professionally design your new bathroom will mean that you know you’re getting the best style of bathroom to fit your room. They can advise you on the best layout, styles, and colours to turn your bathroom into a beautiful space to relax.

It always an exciting decision to extend your home, be it adding to an existing room or building a new one all together. However, the problem starts when you realize there are so many options giving you a tricky challenge of knowing which to choose or where to start. There are great differences in renovations between homes, but a common question that remains is whether to go for a conservatory or an orangery.

There are large array of differences between the styles and knowing a thing or two about the special attributes is definitely a great way to get started. Let’s have a look!

• Orangeries are generally best suited to traditional-styled homes or with older property making use of matching stone or brick in construction. Meanwhile for a more recent or modern property, a conservatory will be the better option to add the flair to your property.

• Conservatories tend to be larger than orangeries, therefore if you want a smaller extension, an orangery would be your best bet.

• Orangeries are typically rectangular in shape and is traditionally a more regular building meanwhile a conservatory can be shaped to suit your needs. With an conservatory, you can get a T-shaped, L-shaped, curved, double ended and lean-to extensions to suit your preference.

• An orangery usually possess a flat roof at the edges with a glazed lantern section right at the centre. You can also find more luxurious orangeries having two or more lantern sections. However, when it comes to the roofing, conservatories generally have more options. Some are gabled or pitched, others are lean-to with a plethora of choice to finish off the roof.

• Due to the fact that orangeries are made of more brick than glass when compared to conservatories, they usually provide more insulation than their counterpart. If your goal is to use the extension during the winter months, then constructing an orangery is the best bet.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

Patios are suitable for many gardens. If you do not have a flat area already, consider having some landscaping work done to create one. If your garden is on a very extreme slope, you could have a multi-layered (terraced) patio with steps between each layer. Ask for advice and get quotes if you're not sure.

Are you having weed problems on your carefully picked out block pavings? After spending huge bucks to install the block pavings, the last thing any homeowner would want to discover is weed taking over the prized asset. Fortunately, this is a problem that can be effectively handled in a few simple steps provided in this article.

Basically, sealing of block paving is all about prevention of weed growth in the area by total weed removal, putting of sand between the block paving joints and sealing with a good quality sealant. This is a task that’s best left for a reliable professional to guarantee the best results especially if you lack proper training and experience. This guide will give a good insight into the process.

Here are the equipment you’ll need to get started: pressure washer, weed killer, bin bag, broom, small brush, protective gear, sealing roller, spueegee, jointing sand and sealer and DIY sprayer.

lRemove The Weed

• Put on a protective clothing and gloves

• Get a weed disposal bag to clean while you go.

• Apply the selected weed killer on both areas where weeds are present and the absent ones to prevent any growing.

lPressure Washing

• Angle your pressure washer between the gaps. This is done to remove all weeds and debris that are still lying around as well as removing all possible chemical residues to create a thorough clean between the paving slab.

• Leave the washed area to dry.

l Sand The Joints

• Check the weather forecast to ensure there’s about 24 to 48 hours of dryness as its important for both sand and sealant to do a perfect job.

• Put sand between the gaps and push it down with your small brush until its levelled.

lSeal The Gaps

• The sealing process should be done immediately and sanding.

• Clean up the patio

• Perform a test using a small area

• Apply the sealant

• Apply the second of sealant

• Leave to dry for about 2 to 3 hours.