Find a Shop Fitter you can trust in Treharris.

Aeration, like scarification, is another vital step to keeping your lawn looking healthy and vibrant. It involves making small holes in the soil to allow air, water and nutrients to get into the grass roots, helping them to grow deeply, and produce a much stronger lawn. It also helps to relieve compaction from the soil, which stops nutrients and air from circulating. But how do you aerate your lawn?

Before you start to aerate your lawn, it’s a good idea to scarify it first to get rid of any moss, dead grass and thatch. This involves vigorously raking your lawn to get all the organic matter up, then transferring it to your compost heap or disposing of it. Light scarification is best in the spring but you can heavily scarify it in the autumn.

If you’ve got a small lawn, you can use a hand-held hollow tine aerator or even a normal garden fork. Dig deep into your lawn’s surface with the fork, or push the aerator into the ground which will pull plugs, or cores, of soil out of the ground to create air holes. You can let the cores dry and then go over them with a lawn mower or rake to spread them evenly across your lawn. This will recycle all the nutrients in those parts of the soil and stimulate bacterial activity to break down unwanted thatch. Don’t leave them, because they will make your lawn look bumpy over time.

If you’ve got a larger lawn, you might find it easier to see if you can hire a petrol aerator. But there are also rolling aerators that have spikes on a cylinder and you just push along, or even aerator sandals that you can wear and just go to town on your grass!

What Is The Smallest Opening For Bifold Doors?

Generally, bifold doors comes in a wide range of sizes and configurations. So if you’re looking to install them in your home, the opening size required will depend on multiple influencing factors. However, the question we’re going to look at here is the smallest opening for bifold doors.

First and foremost, let’s consider the size of bifold doors as learning about how big or small bifold doors can play a key role in helping you determine the size of bifold door you’ll need. Generally, the size of bifold doors will vary largely depending on the manufacturer, but they are usually within the range of 6.8 feet and 7 feet in height. The width, however, will be determined by the number of door panels you’d like to use but several configurations are designed in such a way that they can be installed in openings of about 1.8m and above. For each door panel, the size are usually between 500 and 1000mm in width. As a result, if you decide to opt for door panels with a width of 700mm, you’ll need to get about 3 of the door panels in order to install in an aperture that’s wider than 1.8m. What’s more? Door panels can also be custom made especially if the size you need isn’t available.

So with that in mind, what’s the smallest opening for bifold doors? The bifold door’s minimum width is 1400mm. And in order to install a bifold door to fill this size, you’ll require two individual door panels that’s 700mm in width. Building them any smaller than the minimum width will be unwise as this will make them bind when closing.

Do you have a busy household or a thriving business? When you have a carpeted stairs faced with a high traffic on a regular basis, you know its going to take quite a beating over time. As a result, the carpet tends to start looking tired and worn out almost immediately especially if it isn’t designed to withstand such an heavy usage. Hence, the importance of taking an extra little time when deciding on which new stair carpet or stair runners to purchase and install so as to identify those with sturdier properties which are designed to last and also durable. This way, regardless of the amount of traffic it faces on a regular basis, it’ll always stay looking smart and healthy with good maintenance efforts. In this post, we’re going to consider the best carpet for stairs with a high foot traffic. Let’s take a look!

When looking for a good carpet for a heavy traffic stairs, you need to be able to identify hard-wearing stair carpet runners most of which will be clearly labelled as such. These carpets are designed to handle a high level of footfalls primarily because of the way they’re manufactured and materials incorporated. These materials include sisal (one of the best materials to look out for when you’re shopping for a hard-wearing stair carpet) and polypropylene which is an extremely popular material used in hard-wearing carpets due to its incredible features.

Apart from the materials incorporated, a lot of the strength and resilience also comes from the way in which the fibres are constructed and woven. The most reliable types of carpet weaves to look out for when choosing a high traffic stair carpet runner includes flatweave, wilton weave as well as needlepunch.

Have you laid your tile and left it to set? If yes, then the next step is to start grouting. Before you get started there’s a need to make ready the right grout for the type of your grout as well as background material. If you’re not certain of the right grout you can reach out to the grout manufacturer for help. Grouting of floor tiles is not the easiest and tasks and should be left to a reputable professional in order to avoid costly mistakes and unnecessary costs. In this post, we’re going to take you through the processes involved in grouting of floor tiles in order to put you on the right track. Let’s take a look!

1. Depending on the adhesive used to lay your tiles, make sure you leave enough time for the tiles to fully set.
2. Get a mixing bucket and mix grout powder and water as instructed on the packaging. Ensure not to make too much as this will make it solidify quickly and unstable.
3. Apply some grout on the tiles - hold the grout float at 45 degree angle and apply the grout to fill all of the joints.
4. Once you’re done grouting all of the joints between the tiles, leave it for up to 10 to 15 minutes to dry before wiping down the tile surface using a damp sponge. Ensure not to apply too much pressure on the grout joints.
5. Let the tiles rest for about an hour so as to allow the grout solidify and harden a bit more. Once done, proceed to take off the excess grout and smooth it off.
6. Wipe down the tiles until they’re totally clean using a clean cloth.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

Composite front doors offer a wide range of benefits which includes numerous style and colour options, increased security, personalization options, durability as well as low maintenance requirements. However, with so many options available in the market, it’s also expected that the prices would vary greatly depending on many factors. These factors include the colour, style of the composite door, glazing option, door furniture as well as security locks.

• Colour - More popular and basic colours like white, blue and brown black are manufactured in mass, making them a bit lesser than the unusual colours as they usually go through an expensive colour mixing process.

• Style Of The Door - The most common and popular door styles are manufactured in large quantities and consequently, the cheaper option than the more complex styles. A good example is the six panel door that features two frosted glass inlays will definitely cost more than the four panel plain white composite door.

• Glazing Option - The glass type, design and panel size all play a huge role in determining the price. The more complex your glazing option is, the more money you’ll have to pay.

• Door Furniture - Several composite doors come with bespoke handles, letterplates and knockers to achieve your desired finish. The furniture additions on door can also play a huge role in influencing the overall cost of your composite door.

• Security Locks - Multi point locks typically comes as a standard. However, you might need to determine the type required by your as the quality and type can vary considerably.

Generally, to have a basic style composite door installed, you’ll have spend about £850 and above. And depending on the design requirements and glazing features you select, this price can increase significantly.

• The rules only apply to houses – flats and maisonettes are not included
• Only 50% of the area of land around the original house can be covered by extensions, including conservatories, and other buildings
• You mustn’t build the conservatory higher than the highest part of the original roof
• Where the wooden conservatory comes within 2 metres of the boundary, the height at the eaves can’t exceed 3 metres
• A rear wooden conservatory can’t extend beyond the rear wall of the original house by more than 4 metres if it’s a detached house, or more than 3 metres for any other type of house
• For side extensions, for example a lean-to wooden conservatory, it can’t exceed 4 metres in height and can only be up to half the width of the original house

How To Replace Flat Roof Fascia

Whatever makes you decide to install your flat roof fascia by yourself and not a professional company, then you must have a clear idea of what to do and do it appropriately. If you lack proper training and experience, we’d recommend you employ a reliable professional to help with the task for the best results and save you some time and money. This step-by-step guide will give a clear insight on how to go about the replacement of your flat roof fascia.

The tools to be incorporated includes the fascia boards, table saw, plane, crimper, clamps, power nailer, compound saw and chalkline.

• Prepare and get all the necessary tools to complete the task before commencing as this would save you time from stopping and going back and forth looking for the next tool needed,

• Install the sheathing and board.

• Fix white fascias with at least 600mm centres ( a foiled fascia needs just 40mm centre) using a marine grade stainless steel plastic headed nails.

• Make a space of up to 10mm between the joints for possible building expansion, using super glue to secure the joints to just a side of the fascia.

• Place this directly on the fascia board’s top (if you’ll be installing ventilation) to create an air pathway.

• Take note that the type of roof to be installed will determine how you’ll have to install the fascia board. For instance, a hip roof permits you to attach the fascia board onto the roof in a quick fashion, whereas a gabled roof may need you to make markings on the board to achieve the right fit.

• Consider the depth of the fascia board as it also play a huge role in the installation of the fascia board. For instance, there’ll be additional weights on tiled roofs that will push up against the board. Therefore, if you do not get the appropriate amount of depth, it could eventually collapse.