Find a Shop Fitter you can trust in Hillingdon.

A roof serves as something which is so much more than just a top of a building. A roof delivers guard from the elements and precipitation, it also helps drain water from a structure, and helps to provide insulation to the structure allowing it to keep the interior of a building cool or warm, according to season.

There are several steps to building a roof

Mount the trusses.

This step requires the building’s wall frames to be completely level, square and plumb. If you are building the roof onto a building that is still a frame you must use ladders or scaffolding. Hoist the trusses onto the roof.

Install temporary braces.

You will need to install temporary braces that the trusses can rest on until the sheathing and permanent bracing are installed, this has to be done before you install the trusses. At the centre of the back wall, nail the bottom half of one two-by-six board that's 16 feet long to the top of the outside wall, making sure you fasten it to a stud.

Install the end trusses.

Install the two end trusses at the front and back of the building, making sure you affix them to the temporary bracing. The batten you take will have to be a bit longer than the distance will separate the trusses.

Install the standard trusses.

According to the instructions provided by the manufacturer, you will first need to install the first standard truss. You will also need to nail it to the batten from the first truss.

Sheath the roof.

Once your trusses permanently braced, you can begin with the sheathing of the roof. Starting from the bottom corner and moving across the bottom, the sheathing is installed lengthwise.

Install the roof cover.

Like the sheathing and underlayment procedures, the roof cover is installed lengthwise from the bottom up. The shingles should be staggered, and they should also overlap at the same time. You will need to work up to the ridge and use a ridge cap shingles to finish the ridge.

There are several reasons why you may wish to plant a garden. To have a healthier environment, eat healthier, cook with fresh produce and lots more. Regardless of your purpose, one challenge faced by several home and property owners is exactly how to go about this and where to get started. If you’re having the same issues, then you’ve come to the right place. In this post, we’re going to take you through the process involved in planting a garden to ensure your project turns out a success. If you lack the confidence required to pull this off, we’d highly recommend you call in a professional who can guarantee the best results.

1. Start small. Being overly ambitious when planting a garden could be easiest way to a disastrous outcome. Give yourself a realistic goal and learn to plant healthy and productive plants by starting small.
2. Identify your site. To ensure a great garden, the plants need lots of sunlight. So, you can go for a space that gets about 6 to 8 hours of sunlight on a daily basis. Also, make sure that there’s a water source nearby to make it easy to give your plants water as required.
3. Choose you garden type. Decide how your garden will grow, be it in raised beds, in ground, in containers or a combination of styles. This will ensure that your garden is neat and orderly while also enhancing its curb appeal.
4. Make a list. Create a list of the plants you’d love to have in your garden.
5. Plan your planting. This involves spacing your plants as they’re going to grow bigger, deciding which plant goes where and identifying the best soil to grow them.
6. Get your plants.
7. Plant them.

Did you just purchase a double glazed window and confused about how to have it installed? Fitting the window yourself can be quite easy with the help of this step by step guide. However, if you lack proper training or experience, we’d recommend you reach out to a trustworthy professional who can guarantee the best results for help. That said, now let’s take a look at the process.

• Remove the old windows by detaching the old beading and glass window safely. Then make some interval cuts using a hand saw before using a crowbar to pry it out.

• Cut the external double glazed window seal. Once done, take a measurement of the window area’s width once empty. Then transfer the measurement to the window sil to face outside and cut using a handsaw.

• Seal the window sil. Add a bead of clear silicone along both inside lip as well as the centre to seal the sil.

• Screw the double glazed window to the sil. Position the window on the top of the lipped section that was siliconed. Then pre-drill them together and screw in three places. You should make sure the screws do not go totally to the sil’s bottom.

• Install the double glazed window. After successfully screwing the double glazed window to the sil, you can now fit in the double glazing. Make use of packers to make sure it’s even in the slot.

• Screw the uPVC window to the wall. If you’re happy and satisfied with the position of the window, you can then pre-drill through the frame of the window and the brick wall. Once done, simply screw it in place using masonry screws or Spax screw as they do not require crawl plugs in bricks.

• Seal around the window. To do this, simply fill any gaps with expanding foam, wipe out the excess and seal with silicone.

If a tap is leaking, it may simply be a loose valve or washer. However, if these appear to be sufficiently tight, you should contact a plumber, who will be able to investigate and rectify the leak. Do not attempt to fix leaking or damaged pipes, always call a plumber in straight away.

It depends on the material you use, but if your flat roof is installed correctly it should last for at least 10 years, and at least 20 if a material other than felt is used. Always question a roofing company when they quote to find out what materials they use and what guarantee's they offer.

While some small plumbing jobs can be completed yourself, it’s recommended that you use a certified plumber for bigger jobs. Installing toilets or sinks, repairing leaks, and replacing pipes are all jobs that qualified plumbers will be able to undertake.

Artex is a type of interior surface coating, similar to plaster. It’s used to create decorative textured finishes on ceilings and walls, so it takes longer to dry than plaster.

Artex is actually a brand name, but it’s used to refer to similar products made by other manufacturers too. It was particularly popular in the 1970s, but is still used to create attractive wall and ceiling finishes today.

Lean-to conservatories are often known as Mediterranean conservatories or sunrooms and are a great way to add more living space when you’ve only got a small amount of room to work with. They usually have clean lines, a rectangular shape and attach to the side or rear of your home, which makes them one of the easiest conservatory types to build yourself.

So how do you build a wooden lean-to conservatory? The first step is to decide what you want it to look like. Most lean-to conservatories are constructed of glass and the wood frame, but you can choose to have dwarf walls too. Dwarf walls are low brick walls that are useful if you’re planning to plumb in radiators, have air conditioning installed or put plug sockets in the conservatory.

When you’ve decided what your wooden lean-to conservatory is going to look like, you’ll need to get the materials. You’ll need to choose a hardy wood – oak is the most expensive but also the most durable – and source glass for the windows. You’ll also need to decide on a roof material and work out the correct pitch.

The first step to building your wooden lean-to conservatory is to dig the foundations. You’ll then need to level the earth, then add concrete to the correct height, which should be lower than your property’s existing damp course. Then, you’ll build up to the damp course, which will be your conservatory’s floor level. Don’t forget to make sure it’s even.

If you’re building a dwarf wall, start it from the base and build up to no more than 1 metre high. Once the cement is dry, place external sills on top of the dwarf wall. You’ll then need to secure the frames; start with the one that secures to your property, then do the same for the rest, connecting outwards until they meet from the two sides. Then put up your doors.

Now it’s time to build the roof. This should be simple if you’ve bought your own custom-made kit. Place the roof ridge on top of the frames, then add the roof rafters between the roof ridge and hip bars. Fit your glazing sheets and guttering – it’s important that your wooden conservatory roof has guttering just like your house, otherwise your conservatory roof won’t last very long and could even cause rainwater to rot your wooden frames.

Once you’ve built your wooden lean-to conservatory, all that’s left is to decide on how you want to decorate it. But if this all sounds like too much, get in touch with specialist wooden conservatory installers who will be able to give you a quote for building you a lean-to conservatory.