Find a Shop Fitter you can trust in Bacup.

If you’re considering laying gravel on your driveway, then you’d probably want to know the amount of gravel you’ll need to complete the project. When you are calculating the amount of gravel you’ll require to cover your driveway, there’s an important factor you’ll need to consider and that is the type of gravel you opt for such as a crushed or pea gravel. There are varying grades which are found in particles from fine to course, with a size ranging from 2mm to 64mm. Therefore, there’s a need to estimate the volume of the gravel while also having the rock’s size in mind. Also, there’s a need to select your most preferred gravel which you’ll like to use before proceeding to dig the depth of your driveway and subsequently determine the amount of gravel that’ll be needed using these excellent tips.

✓ Determine the size and coverage. As you would have expected, the smaller the gravel is, the bigger the coverage will be, and gravels should be at least 4 inches deep. However, if the rocks happen to be a bit large then you can allow for an extra 1/2 inch.

✓ Measure the driveway. Multiply the width by the length and depth to get the size of the driveway in cubic feet. Meanwhile for cubic yards, you can divide the total cubic feet by 27. This is due to the fact that one cubic feet is same as 1.13 tons.

✓ Working with gravel. Here, you’ll have to calculate an underlay measurements differently. You can use 2 inches of road base that’ll be overlaid with 2 inches of gravel.

If your boiler is making strange noises or smells, or doesn’t seem to be working properly, it may need replacing. Boilers usually last about 10-15 years. Even if your boiler is working normally, it’s worth replacing when it gets this old. An annual check will establish if there are terminal problems with a boiler that cannot be fixed.

You should replace your soffits and fascias if you are having problems. Soffits and fascias can degrade and rot away over time, and this can cause leaks, faulty guttering, or even allow pests entry to the roof space. If any of these problems occur, you should speak to an experienced roofline company to discuss replacing your soffits and fascias.

Do I Need Planning Permission For A Wooden Conservatory?

The addition of a conservatory to your home is classified as a “permitted development and according to the 2008 legislation, you do not need to apply for a planning permission to add a wooden conservatory to your home so far you are within some particular limits. These regulations are summarized below:

• All extensions must not be more than one storey and the height must be lower or equal to the existing building’s roof or 4m at the maximum.

• There are multiple limitations on the extent you can extend from your existing property depending on a few factors such as the type of your house as well as the location of the extension, be it at the rear or side of the building.

• If your wooden conservatory is to be constructed at the rear, it must not go beyond 3 metres from the attached house’s original property and 4 metres in a detached house. Also, the wooden conservatory mustn’t go beyond half the space around the property.

• The wooden conservatory must not go beyond half the size of the original house. Similar conditions govern that of the space around the existing building.

• Extensions that are not covered by the permitting rights are the ones constructed in front of the property or those directly facing the main street or road.

• Listed Building content may be needed in the event whereby there’s a Listed Building proposed work.

This is just a brief of the conditions that applies, however, the fact remains most property owners can have a wooden conservatory installed without having to apply for planning permission. It is advisable to consult your local planning office before you construct an extension. In certain cases, all work may require planning permission if there’s a permitted development rights removal. Click here to learn more about wooden conservatories

Several individuals think that the the way their air conditioning system works is simply by pumping hot air out of their homes or offices, blowing a cool air in return. This is absolutely wrong! The hot air is, in fact, cycled back in as cold air and this process continues until the thermostats gets dropped down to the required or set temperature. The air conditioning system manages this in a similar way to how the refrigerator manages to stay cold and of course, excluding the insulated box.

The short and simple answer to the question of what gas an air conditioning use is Freon. This is a non inflammable gas which is subjected to the evaporation process over and over again in most refrigerators to keep the temperature at a low level. This same process is repeated in air conditioning systems. Now let’s take a look at how the Freon gas is incorporated in AC systems.

The cold Freon gas is firstly compressed by a compressor in the air conditioner. The gas is then combined with a little quantity of oil in order to lubricate the compressor. When Freon gas is compressed, the pressure is increased which makes it incredibly hot. It then moves through a couple of coils which works to lowering the heat and turning it to liquid. This Freon liquid will then be transmitted via an expansion valve which causes it to cool down until evaporation takes place. The outcome of this is a low pressure cold Freon gas which is then transmitted via another set of coils allowing the gas to collect the heat and lower the air within the room.

The air conditioner now filters the air and clears out the dust, smoke, pollen and other kinds of air pollutants. The system also absorbs excess liquid from the air too which it uses to cool down the system and pump it through a hose.

Patios do not require lots of maintenance. They will only need occasional cleaning to make sure that the material keeps its original appearance. It's always best to clean your patio with a pressure washer and occasionally tap each slab or brick just to check the sand underneath hasn't washed away.

If you’re considering getting a solar thermal system, one of the first things that comes to mind is the possibility of the system functioning properly during the cold months. The short and simple answer to this question is yes, a solar thermal system works in the winter. However, the downside here is that it’ll be a lot less efficient when compared to how it operates during the warmer months or summer. As a result of this fact, you’ll likely need to rely more on your boiler, immersion heater or any other backup heating system during this period as your solar thermal system will fail to contribute as much as it does during the warmer months. So what exactly is the reason why solar thermal is less effective and less efficient in the winter period? Let’s have a look!

As you know, solar thermal system banks on the sun’s energy to heat the water for your home’s use. During the cold months or winter, the sunlight becomes a lot less available when compared to the warmer months, as a result, there’s less sunlight that’s available to be used for its solar energy. And even more so at the periods when the days are shorter or skies are clearly overcast.

Also having a great impact on a solar thermal system’s output is heavy snow. Flat plate collectors normally have the capacity to cope better during snowy conditions as the light that’s able to travel through the snow will heat up the absorber plate - thereby making the snow slide off more quickly. However, the case is contrary with evacuated tube collectors which possesses a form of vacuum insulation that’s crafted to minimize the loss of heat, meaning they can’t generate heat to melt and cause the snow to slide off in a similar way.

In many instances tree surgery work can still be carried out on trees that are protected by Tree Preservation Orders (TPOs). Tree surgeons will be able to file the needed forms with the local authority to arrange such work, and advise you throughout the entire process.