Find a Shop Fitter you can trust in Isle Of Eigg.

Many doors are made to measure. If you require a non-standard door width, ask a professional door installation company to measure your aperture and manufacture a door to fit. It could be that a small amont of brickwork is needed to accomodate the new door.

Does your old TV aerial cable have a cut or tear in line? Well, good news is, you don’t have to discard it. When such problems occur, they can lead to loss of conductivity or interference which results in weak or poor reception or even none at all. With a few easily accessible coaxial repair tools which can be obtained from local stores, repairing your aerial cable can require a much less effort than you think. In this post, we’re going to take you through the TV aerial cable repairing process. Let’s take a look!

• Identify the part of your coaxial cable that needs to be repaired. Incorporate wire cutters to make a clean cut across the damaged cable portion.
• Close the RG-6 labeled groove of the crimping tool an inch down the cable and make a complete cut around the exterior part of the cable.
• Cut the exposed aluminum braiding around the insulation to leave the copper filament above the cut portion which is usually surrounded by a white PVC insulation.
• Using the part of the stripping tool labeled “inner, cut between the insulation down to around 1/3 inch. Once done, twist the stripper around the section to get a clean cut and take off the portion that is cut.
• Identify the copper filament positioned at the middle of the cable and surrounded by insulation and thread it through the twist-on connector’s base.
• Strip the damaged coax cable’s other end and add a twist-on connector to it.
• Use a coupler to connect the two repaired cables. To do this, simply screw one end of the first cable to one side of the cable coupler and do the same to the second cable to the other side of the coupler

Properly erected fences shouldn’t require a great deal of maintenance. Any rotting boards can usually be replaced without replacing the whole panel. Timber fencing should be stained every 2-3 years. General maintenance is something you can carry out yourself, however, larger works may need a qualified professional to come in.

The A-G scale refers to the energy efficiency of your boiler. G-rated boilers are the least efficient, and give you less heat and hot water for your money. Installing an A-rated boiler will reduce your energy bills and carbon emissions. Don't compromise on cheaper, lower rated boilers, you will save yourself more money longer term with an A-rated model.

Most domestic solar thermal panels do not need planning permission and are covered by permitted development rights. There are restrictions on the size and location of these systems. If you live in a conservation area or listed building, or want to install a very large solar thermal system, check with your local authority to see if you will need planning permission.

It may be hard to believe with the summers we have in the UK, but there is more than enough sunlight to power solar panels. Solar PV (photovoltaic) panels operate in daylight, rather than needing direct rays from the sun so they’ll work throughout the year.

Are you having weed problems on your carefully picked out block pavings? After spending huge bucks to install the block pavings, the last thing any homeowner would want to discover is weed taking over the prized asset. Fortunately, this is a problem that can be effectively handled in a few simple steps provided in this article.

Basically, sealing of block paving is all about prevention of weed growth in the area by total weed removal, putting of sand between the block paving joints and sealing with a good quality sealant. This is a task that’s best left for a reliable professional to guarantee the best results especially if you lack proper training and experience. This guide will give a good insight into the process.

Here are the equipment you’ll need to get started: pressure washer, weed killer, bin bag, broom, small brush, protective gear, sealing roller, spueegee, jointing sand and sealer and DIY sprayer.

lRemove The Weed

• Put on a protective clothing and gloves

• Get a weed disposal bag to clean while you go.

• Apply the selected weed killer on both areas where weeds are present and the absent ones to prevent any growing.

lPressure Washing

• Angle your pressure washer between the gaps. This is done to remove all weeds and debris that are still lying around as well as removing all possible chemical residues to create a thorough clean between the paving slab.

• Leave the washed area to dry.

l Sand The Joints

• Check the weather forecast to ensure there’s about 24 to 48 hours of dryness as its important for both sand and sealant to do a perfect job.

• Put sand between the gaps and push it down with your small brush until its levelled.

lSeal The Gaps

• The sealing process should be done immediately and sanding.

• Clean up the patio

• Perform a test using a small area

• Apply the sealant

• Apply the second of sealant

• Leave to dry for about 2 to 3 hours.

With the numerous benefits that comes with the installation of solar panels, it should not be an option for just a few just because of the size and/or pitch of their roof. A number of individuals with flat roofs decide against solar panels due to the fact that they believe that the panels can’t be installed due to the lack of direct sunlight. However, in truth, this thought is absolutely incorrect. This is because it is actually very possible to fit solar panels on flat roofs and you can also benefit from a good amount of electricity that’ll be generated over time. In this post, we’re going to look at the possibilities involved in the installation of commercial solar panels on a flat roof. Let’s get started!

In reality, flat roof solar systems are mostly found on commercial buildings as their roof is typically made to be flat. Although, it’s important to note that it’s absolutely possible for them to be fitted on domestic properties too. The type of solar array that’s installed makes use of the same type of solar panel as a conventional system, however, there are some considerations that’ll have to be made moving forward. The array must be able to self clean during the rainy season while also avoiding damage whenever there’s a strong wind. The installation company you choose should take the pitch of the system into account, so as to make sure that its able to capture as much energy from the sun as possible. And that’s exactly why you should consider the use of thin film solar cells which are very flexible and moves with the sun as the day goes by, securing as much sunlight as possible as its always in direct light.