Find a Shop Fitter you can trust in Rowland's Castle.

For most homeowners, rewiring a house is always a sore subject they’d prefer to avoid especially when they think of the expenses they’d have to incur or the mess and complexity that the project involves. However, this is a subject we’d all have to face sooner or later as an old wiring poses a lot of drawbacks, while an improper wiring can also prove to be more expensive and even cause more damage as it can lead to not only electrical shorts but also electrical fires. When a wire triggers a spark or a current overload, this can cause fire and the entire house may be down in ashes within a couple of minutes. Hence, one of the several reasons why house rewiring is just too important to ignore.

In this FAQ, we’re going to take you through the house rewiring process so as to ensure that your project is done to perfection. However, if you do not feel confident enough to pull this off, we’d strongly recommend you get in touch with a reliable electrical professional who can guarantee that a safe and effective work is done.

• Firstly, you’d have to upgrade the main service panel to a minimum of 100 amps
• Fit dedicated circuits in the service panel for all the home’s major appliances.
• Allow for a space of about 6 to 8 feet between electrical outlets throughout the house in order to cut out the need to run extension cords which could be a fire hazard.
• Install only three-prong type to avoid electrical shocks when fitting new outlets.
• Using ground fault circuit interrupters, fit outlets in the bathrooms, kitchen as well as outdoors. These outlets will shut themselves out so as to prevent electrical shock when wet.

What Size Of Electric Boiler Do I Need?

If you’re thinking about installing central heating in your home or property, you’ll be shocked by the plethora of options that’s currently available in the market as regards the boiler type that can be installed. Being a very good alternative to gas boilers or an oil or LPG boiler, electric boilers are here to stay. They usually feature different power outputs which tends to lead to one of the most frequently asked questions about electric heaters - what size of electric boiler do I need? Here, we’ll give you a good insight into sizes of electric boilers available to help you make the right decision.

The importance of getting the perfect size of electric boiler for your home can not be over-emphasized. If your electric boiler size is too small, it won’t be able to provide the level of heat and hot water required. And on the other hand, if it’s too big, it’ll definitely consume more electricity which would be a total waste of money.

To determine the correct size, if you have a wet central heating or water radiators in your home, you’ll need to calculate the boiler’s capacity required to operate them and allow 1.5kw per radiator. To be more accurate, it’s advisable to talk to a professional installer to avoid making a costly mistake. Every professional installer should have an idea of the appropriate size of electric boiler that’ll be needed given your special requirements and home size.

Generally, with a 12k kilowatt boiler, you should be able to operate up to 7 to 8 radiators which is good for smaller properties. For apartments and flats, getting a smaller electric boiler would be the best option.

The most basic fencing starts at about £27 per panel. But if you want something that’s more decorative and better quality, expect to budget £30-£40 per panel.If you choose to get a professional to help you put up your fencing, they’ll probably be able to get your panels at a cheaper rate.

It depends on the size and type of extension. Small porches or flat roof extensions are very reasonably priced. More substantial two storey extensions can be expensive. In general, the price is roughly proportional to the amount of space you add to your home.

The amount of maintenance will vary depending on the material of the gutter. However, all gutters should be cleaned regularly. Ideally cleaning should be carried out yearly, or more frequently if there are trees close to the guttering, this prevents overflows and problems elsewhere.

Home electrics can be extremely dangerous and it’s very unwise to try and carry out repair work or maintenance yourself without the necessary knowledge and skill. Therefore we would always recommend using a Part P registered electrician at all times.

This varies according to the quality of the conservatory and installation work. If these are both high quality, your conservatory should last at least 25 years. But obviously if you notice deterioration or leaks, then this could be an early warning sign that time is running out.

Tiling a porch roof is a very important but laborious and difficult task. A project of this magnitude will require a large investment in planning and preparation way before the actual installation process takes place. It can be a brand new porch roofing tile or a replacement of the existing one, either way it’s crucial to get the right technique. If you lack proper training or experience in this field, we’d recommend you hire the services of a reliable professional probably within your local area to guarantee the best results and to save yourself some time and money. This guide will give you a good insight into the porch roof tiling process. Let’s have a look!

• With the crown looking upwards, put the first tile on the batten and centre the tile from side to side.

• Hammer a 10d nail at the base of the tile and into the batten (make sure not to overdrive the nail).

• To provide a much needed support, apply a little mortar under the first tile.

• Identify the inner end of the first tile and place another tile on top. Take a measurement from the outer end and adjust the end of the second tile to fit.

• Just like you’ve done with the first tile, nail the second tile into the batten.

• Position two tiles at the both ends of the ridge and proceed with the installation just as you’ve done with the previous tiles.

• Take a measurement of the distance across the ridge from the first tile’s outer end. Once done, you can then calculate the number of tiles required by subtracting 16 inches from your measurement and divide the answer by 8.

• Beginning at the second tile on one end of the ridge, install the half the number of ridge tiles towards the centre of the ridge. Now install the remaining tiles working from the opposite end to the ridge’s centre. At the centre of ridge should be a key tile with mortar.