Find a Shop Fitter you can trust in New Milton.

If your property is not connected to a gas main, oil boilers are a great alternative to gas boilers and more efficient than LPG alternatives. They can also be paired well with renewable sources. However, if your property is connected to the gas mains, there is generally no reason to switch to an oil boiler, as you will need to have oil delivered to an extra storage tank.

If you’re planning on adding a house extension to your property, you’d probably be worried about whether or not your proposed extension would require a planing permission. Well, it may be relieving to know that not every house extension project would require a formal consent, and in fact, several extensions are covered by the permitted development rights. Not only can this save you a considerable amount of time especially at the project’s planning phase, but it’ll also save you money on the application fee. In the UK, single storey extensions to the house’s rear can be 3 metres deep for both semi detached houses and terraces or 8 metres deep for detached homes.

So how do you know when you’d require a planning permission for your home extension? Well, if your extension plan fits these criteria explained below, then your project is most likely going to be allowable as a permitted development.

• Extensions, which includes previous additions, must not go beyond half of the original house’s total surrounding land area.

• The main elevation, or side elevation where it fronts the highway, must not be extended forward.

• For single storeys, the rear additions must not extend more than the original house’s rear by more than 3 metres in both semi attached homes and terraces (4 metres for detached houses).

• Extensions to the side must be a single storey with a height not exceeding 4 metres and not going beyond 50% of the original house’s width.

• Extensions hat within 2 metres of a boundary should have a eaves height not more than 3 metres.

• Multi storey addition must not extend beyond the original house’s rear wall by a maximum of 3 metres or 7 metres of the boundary opposite the rear wall.

• Permitted development rights do not apply in listed buildings or designated areas.

How to repair your flat garage roof will depend on what it’s made from. Lots of flat garage roofs are made from EDPM rubber, asphalt or felt. We’ll explain how to carry out repairs on your garage roof here. EDPM rubber flat roof repair EDPM rubber is an excellent choice for a flat garage roof and should need little maintenance. But if you do need to repair it, there are a few easy fixes. If it’s a small crack or tear, apply some lap sealant to the area, but don’t use too much. If you go for a more professional repair later, the sealant will need to be scraped off, so if there’s too much it might cost you more in labour. If you need to repair the flashing, buy some malleable flashing tape so you can form it into the right shape. Clean and dry the area that needs repairing, then apply an EDPM primer. When that’s touch dry, stick the patch of flashing tape down from the centre outwards with a roller. Repairing an asphalt flat garage roof Asphalt is also very hard-wearing, and when it does need fixing, the fixes often last a long time. So if you do get cracks or blisters, you can use a paint-on fix from a tin as a temporary repair. When it’s time for a more permanent fix, you can add a small patch of torched-on roofing felt or use a liquid system, but the high-quality ones are often only available to trade customers. How to repair a felt flat garage roof Felt can be repaired in a similar way to asphalt flat garage roofs. For small cracks or a temporary fix, try a paint-on treatment from a tin. But for something more permanent, use a patch of torched-on roofing felt or a liquid system. If these don’t stick, unfortunately it means it’s time for a new felt garage roof. If you do need a new flat garage roof, leave it to the professionals who will ensure that your new roof will last for years.

Solar thermal panels are panels that can be used to heat your hot water. The collectors, which are either evacuated tube panels or flat plate collectors, harness heat from the sun and transfer it to a heat transfer liquid that heats up water that is stored in a hot water cylinder. You can use a boiler or immersion heater as a back-up in the winter or to heat the water up further to reach the right temperature.

Evacuated tube panels involve a bank of glass tubes mounted on the roof tiles, and while they’re usually more expensive, they’re more efficient than flat plate collectors. They’re exactly what they sound like – flat panels that can be fixed onto your roof tiles or integrated into the roof.

Having a solar thermal system will reduce your energy bills since heat from the sun is free, so you won’t have to rely on your traditional heating as much. You’ll also be doing your bit for the environment – if you have a natural gas heating system, you could save up to 295kg of CO2 every year.

Another benefit to solar thermal panels is that you might be eligible for payments through the Renewable Heat Incentive (RHI), which is a Government scheme to encourage people to take up renewable heating technologies. As long as you have your system installed by an MCS-registered installer and you meet a few other requirements, you could receive payments of up to £525 per year for seven years. And since the average solar thermal panel system costs £5,500, you could pay off over half of your system just with these payments. That’s not even considering that you could save up to £60 a year on your energy bills if you have a gas system.

Thanks to its durability, resistance to moisture and stain as well as aesthetic appeal, ceramic tile is a popular material for floor installations. The same qualities that makes it stand out for both kitchen and bathroom floors also makes it a natural choice for walls.

Fitting of ceramic wall tile is a task that requires pre-planning and lots of patience. Generally, it’s usually not that difficult to do but it can be very easy to make mistakes here and there. And because you’ll have to attach a relatively heavy material to vertical surfaces, the project can be somewhat trickier than ceramic floor tile so more care and skill is required here. This can be done by any competent DIYer who is confident and also patient. If you lack any of these attributes, we’d recommend you call in a professional who can guarantee the best results for help. In this article, we’ll take you through the ceramic wall tiles fitting process. Let’s take a look!

✓ Prepare the room. This includes switching off power to electrical outlets, removing decorative wall plates and other accessories on the wall, protecting the surface and taking out the baseboard.

✓ Draw reference lines. Using a chalk line draw a reference line on the wall to be tiled.

✓ Spread the adhesive. Use a notched trowel to spread the tile adhesive

✓ Install the first tile. Use the reference line as a guide to fit the first tile near the centre of the wall, twisting it slightly so its firmly in place. Then check to ensure the tile is level and adjust if you deem fit.

✓ Install all tiles. Following similar technique to install the remaining tiles and use tile spacers to ensure even gaps

✓ Clear out excess adhesive and remove spacers.

✓ Apply grout. Dampen the grout with clean water before the grout application

✓ Caulk the joints. After like 10 days, use silicone sealer to caulk the expansion joints.

With the numerous benefits that comes with the installation of solar panels, it should not be an option for just a few just because of the size and/or pitch of their roof. A number of individuals with flat roofs decide against solar panels due to the fact that they believe that the panels can’t be installed due to the lack of direct sunlight. However, in truth, this thought is absolutely incorrect. This is because it is actually very possible to fit solar panels on flat roofs and you can also benefit from a good amount of electricity that’ll be generated over time. In this post, we’re going to look at the possibilities involved in the installation of commercial solar panels on a flat roof. Let’s get started!

In reality, flat roof solar systems are mostly found on commercial buildings as their roof is typically made to be flat. Although, it’s important to note that it’s absolutely possible for them to be fitted on domestic properties too. The type of solar array that’s installed makes use of the same type of solar panel as a conventional system, however, there are some considerations that’ll have to be made moving forward. The array must be able to self clean during the rainy season while also avoiding damage whenever there’s a strong wind. The installation company you choose should take the pitch of the system into account, so as to make sure that its able to capture as much energy from the sun as possible. And that’s exactly why you should consider the use of thin film solar cells which are very flexible and moves with the sun as the day goes by, securing as much sunlight as possible as its always in direct light.

Ultimately the double glazing company you use is responsible for the quality of work and to ensure your windows are of an excellent standard. This is why it’s important to get a warranty and use a Fensa registered installer. If problems emerge within a couple of years then it’s likely the installation was of a poor standard.Contact the double glazing company and have the issue repaired or new windows replaced. This doesn’t matter if you received a discount of free windows as part of the deal. As long as you entered into a contract the company is obliged to restore the windows.

Your LPG storage tank will need to go outside your property, possibly underground if you have limited space. There are planning rules that restrict where you can put your tank, especially if your property is listed or on designated land. Take a look at our planning permission article to find out more.