Find a Shop Fitter you can trust in Fife.

Kitchen floor tiles are a very popular choice for several reasons. They’re durable, visually appealing, resistant to moisture and stain and also relatively easy to maintain and install especially when compare to wall tiles. This is a task that can be done by any competent DIYer but requires a lot of patience as well as confidence. If you lack these attributes, then we’d recommend that you hire a professional floor tiler who can guarantee the best results the first time. In this article we’ll take you through the kitchen floor tiling process. Let’s get started!

• Prepare The Subfloor

✓ Ensure the subfloor is very secure to support both the tile and the people working across it.

✓ If necessary, you can strengthen the kitchen floor with the help of a vinyl, heavy felt or any other good backer board.

✓ After successfully securing the floor, proceed to clear out all dust and dirt.

• Mix The Mortar

✓ Mix a thinset mortar be referring to the instructions on the package. ( Mix only the quantity you can apply within 30 minutes).

✓ Once the mixture looks similar to the thickness of mayonnaise, allow it to rest for about 10 minutes before application.

• Apply The Mortar

✓ Apply a thin layer of mortar

✓ Do not cover extensive areas as the mortar can become very dry.

✓ Spread the mortar with a trowel in curved patterns to make it flat on the floor.

• Set The Tile

✓ Set down the tile slowly, apply a little pressure until its holds firmly to the surface. ( Apply a consistent amount of pressure throughout to ensure equal heights for all the tiles)

✓ Continue with the process until all full tiles are well positioned

• Cut The Tiles

✓ Once all the full tile pieces are in place, start cutting to cover the edges requiring smaller tile pieces.

✓ Take accurate measurements of the outer edges needing smaller tile pieces.

✓ Cut the tile pieces to fit the measurement taken with the help of a wet saw or hand tile cutter.

• Grouting

✓ Remove all spacers and mortar residues and lay the grout

✓ Apply the grout along the tiles’ seams with a grout float

✓ Clean out excess grout with a damp sponge after leaving it to dry for about 30 minutes

✓ Once the grout is fully dried, apply the sealer (the drying process normally takes within 3 to 4 days).

Are you about to replace your old windows and wondering just how much it’ll cost to have a new one fitted? If yes, then you’ve come to the right place! The question is a very straight forward one, however a direct answer can not be provided as determining window prices for a replacement project can be a very tricky challenge. With a plethora of influencing factors that can play a key role in the price of both materials and labour to be used, it could be extremely hard for a window installer to provide a cost estimate without paying you a visit beforehand.

The factors that can go a long way in determining the price of your new window includes the size of the window, frame material, style chosen, your location, rates charged by the window installer (these rates can be different from an installer to an installer, so it’ll probably be in your best interest to compare quotes to identify the most competitive price) as well as the type of glass required.

Generally, for a small flat featuring four windows, the average cost for new windows would be between the range of £2,100 to £2,300. This range provided covers the cost of double glazed uPVC casement windows as well as the installation price. In the same tone, a home with up to 8 windows will have an average cost for window replacement between the range of £4,400 to £4,600, wile also taking into account the installation price. Whereas a house comprising 10 windows could begin at an average cost of window replacement between the the range of £5,200 to £5,500, and a 15 window home will be between the range of £8,400 to £8,600. it should be noted that the aforementioned figures only include the standard number of windows with a uPVC frame and the installation cost.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

How Wooden Conservatories Add Value To My Home?

Wooden conservatories does not only offer a bright and exciting way to increase both your entertainment and living space, but can also go a long to add immense value to your home. If you recruit master craftsmen to utilize superior quality wooden materials to build your conservatory, it can boost the value of your property by 5 percent - ranging between £13,000 to £15,000.

Like many other construction projects, the amount of value that’ll be generated by a wooden conservatory depends largely on the quality of the materials and construction utilized. A higher quality wood like an Oak or Iroko will definitely add a greater value to your home than woods of a lesser quality.

Below are some good points you can put to use to ensure you get the best return on investment.

• Do not alter your home’s style

If you have a modern home, building a traditional conservatory would not only make your home have an inconsistent appearance, but also reduce its value. Ensure that your wooden conservatory has a similar style to your home to derive maximum value.

• A great looking and professionally done wooden conservatory equals a great value

To maximize the possible benefits from your wooden conservatory, it is essential to use a reputable company with a fantastic portfolio.

• Strike a balance between garden space and your conservatory size

A big or moderate outdoor space is just as valuable as your wooden conservatory. So when building your conservatory, do ensure to take the outdoor space into consideration, as a little garden space can imply a negative ROI.

• Consult a local estate agent

The size, style and construction of your wooden conservatory can greatly impact its value. A local estate agent can assist you to determine the potential ROI.

Click here to learn more about wooden conservatories

The energy efficiency of windows is measured using ratings, varying from A, the most efficient, to G, the least efficient. This scheme is run by the British Fenestration Council (BFRC). To comply with Building Regulations you’ll need windows of energy efficiency at least level C.

If you’re considering laying gravel on your driveway, then you’d probably want to know the amount of gravel you’ll need to complete the project. When you are calculating the amount of gravel you’ll require to cover your driveway, there’s an important factor you’ll need to consider and that is the type of gravel you opt for such as a crushed or pea gravel. There are varying grades which are found in particles from fine to course, with a size ranging from 2mm to 64mm. Therefore, there’s a need to estimate the volume of the gravel while also having the rock’s size in mind. Also, there’s a need to select your most preferred gravel which you’ll like to use before proceeding to dig the depth of your driveway and subsequently determine the amount of gravel that’ll be needed using these excellent tips.

✓ Determine the size and coverage. As you would have expected, the smaller the gravel is, the bigger the coverage will be, and gravels should be at least 4 inches deep. However, if the rocks happen to be a bit large then you can allow for an extra 1/2 inch.

✓ Measure the driveway. Multiply the width by the length and depth to get the size of the driveway in cubic feet. Meanwhile for cubic yards, you can divide the total cubic feet by 27. This is due to the fact that one cubic feet is same as 1.13 tons.

✓ Working with gravel. Here, you’ll have to calculate an underlay measurements differently. You can use 2 inches of road base that’ll be overlaid with 2 inches of gravel.