Find a Shop Fitter you can trust in Etchingham.

Depending on the size and location of the blockage, a blocked drain may be fixed by simply removing the build-up. This can be done either by using drain cleaner or physically removing the blockage. If the blockage is very serious or located within the pipes themselves, you will need to contact a plumber.

It depends on a few factors whether a new double glazed window will look different to existing ones. If your existing windows are very old, perhaps 10 years or more, then it’s likely that there will be some small differences.

The first thing to remember is that your double glazing is exposed to the elements as soon as it’s installed. So over time, unless you’re very good at cleaning and maintaining your windows, they’re likely to look a bit dirty. Window frames that are south-facing may also become slightly discoloured from the sun, so if you install a new window right next to it you might notice a difference.

Also, there have been lots of technical advances in windows over the years. If your existing windows are significantly older, you might notice a difference in the handles on openers, and if your existing windows were installed before 2010 they might not have trickle vents, which is an extra strip on the inside of your window to keep air flowing through your home. While it’s not a legal requirement for replacement windows to have trickle vents if the original one didn’t, it’s a good idea to have them installed as they help prevent condensation and mould.

The only truly noticeably different elements to a new double glazed window compared with existing ones are likely to be on the inside, which might not be a problem for you if you only have one window in a room. However, if you know the brand of your existing windows, you can ask your window installer if they can source the same ones. Even if they’ve been updated slightly, the difference should be minimal.

When people think about heat pumps, they’ll automatically have the believe that a swimming pool will require a big heat pump. Since the swimming pool has a large volume of water, then warming such a volume will require a large ground source heat pump because that volume is much larger than the normal domestic hot water tank, right? Well, that point of reasoning does seem logical especially with the information almost everywhere that ground source heat pumps are usually less efficient when it comes to heating hot water for home’s use. However, the fact is there are also some things to put into consideration that also works in favour of the ground source heat pump.

First and foremost, you should know your domestic hot water will typically be heated to a much higher temperature when compared to your swimming pool. Since you wouldn’t be using the water to disinfect your bathroom or doing your dishes in your swimming pool, then the temperature can be much lower. In fact, it’s much more comfortable and enjoyable to heat to a typical “swimming pool temperature than having it at a hot bath temperature. If you’ve ever wandered into a really hot swimming pool, you wouldn’t need any introduction to the painful discomfort that comes next.

As a result of this low temperature, your “tiny heat pump can operate a in a more efficient way which makes the use of ground source heat pumps a viable swimming pool heating option. What’s more? The ground source heat pump works for a swimming pool just like any any other application - moving the heat from the region of a warmer temperature to the cooler temperature region.

If you’re looking to plaster your ceiling, one of the most essential parts of the process is cutting the plasterboard. Once you’re able to master this skill, the rest of the plastering is quite easy. This is a task that can be done by any competent DIYer but with a little bit of patience and confidence. If you lack any of these attributes, we’d strongly recommend you call in a reliable professional who can guarantee the best results for help. In this guide, we’re going to take you through the plasterboard ceiling cutting process. Let’s take a look!

To cut plasterboard ceiling, you don’t need any expensive tool which is usually not the case when it comes to carpentry. If you won’t be cutting a lot of plasterboard, all you really need would be just an old handsaw or plasterboard one, a Stanley knife as well as a straight edge. However, if you’ll be cutting lots of plasterboards, you’ll require the following to make your task a lot easier:

✓ An old handsaw

✓ A Stanley knife and many spare blades

✓ A straight edge like a long spirit level

✓ A surform

✓ A battery drill and oh2 screwdriver bits, with specific plasterboard screws.

To cut plasterboard to length, you’ll have to first score a line on the face side of the board with a straight edge and Stanley knife. Once done, simply lift the sheet off the ground and snap it along the score line. Then, you can run your knife down the other side of the board , cutting the back of the plasterboard backing sheet. Upon completion, your plasterboard is now ready to be fitted on your ceiling.

Most companies will make the building control application on your behalf and ensure that all the work is completed to the right standards. When a building inspector has inspected it, you’ll get a certificate. It usually takes around 6-8 weeks after completion to come.

With each year that passes, the amount of electric cars on the road keeps rising and with them comes a necessity to develop new infrastructures and also accessories like charging cables as well as connectors for easy sustainability. This concept is still pretty much new to the general public as most people still use vehicles that are fuelled by petrol and diesel. There are also some differences in design which asides from the lack of an engine underneath the vehicle’s bonnet, the way in which an electric car is filled up largely varies petrol or diesel powered vehicles. There’s a lot that people will have to learn about electric cars and even more so when it comes to their everyday use. One of the most common questions a lot of individuals ask about electric cars is whether all electrical vehicle chargers are the same. If you’re also looking for an answer to this question, then you’ve come to right place!

If you’re interested in getting an electric car, charging your vehicle at home may not generate any major concern but what about making use of the public charging system? This is when it gets a bit confusing because if you’ve never had to do it before you may worried about making use of the wrong charger on your car. So the question is, does every electric vehicles have the same plug? The answer is simple - there are different plugs and cables for varying electric vehicle brand as well as points of use. In general, you’d have to choose most suitable charging level for your electric vehicle.

There are a wide array of smart ring doorbells available in the market today and all coming with detailed installation instructions. Here, we’ll make it clearer to enable you get it done right, the right time and with little stress. With a properly installed ring video doorbell, you’ll be able to identify who’s at the door before opening and even chat with them via your table, PC or Smartphone. And to make it even more interesting, you can easily install a ring doorbell yourself and save some money.

Installation Steps

• Assemble the mounting bracket

Bring out the mounting bracket that comes with your ring video doorbell. You’ll discover a small level within the mounting bracket, put this on the bracket’s slot. Once done, gently line it up to the spot where you want to place your doorbell.

• Determine the pilot holes

Firstly, ensure the bubble found in the level is straight. Then, mark out where the screws will go through.

• Drill the identified pilot hole spots

When drilling, you’ll need not just your drill and drill bit (or a masonry bit, if its a brick), but also your eye and ear protection. Drill the marked out spots to create pilot holes and subsequently hammer in the plastic anchors that comes in the ring doorbell’s pack to help hold your screws in place. Once done, put the bracket on the top and tighten your screws.

• Scan the QR Code

With the use of your phone, scan the special QR code given behind your doorbell to ensure the ring doorbell is only accessible by you and your loved ones.

• Secure the doorbell

Ensure that the bracket is properly in place and attach your doorbell to the mounting bracket. Once done, you can make it safe by using smaller security screws to hold it. Upon completion, your ring doorbell is ready for use - it’s that easy!

The energy efficiency of windows is measured using ratings, varying from A, the most efficient, to G, the least efficient. This scheme is run by the British Fenestration Council (BFRC). To comply with Building Regulations you’ll need windows of energy efficiency at least level C.