Find a Shop Fitter you can trust in Dunbartonshire.

How Much Are Bifold Doors?

Are you considering installing bifold doors for your home or property? If yes, then you’d probably want to know how much it would cost so you can prepare a budget and start planning. The cost of bifold doors, however, is dependent on a wide array of factors which includes the number of panels, size of the bifold doors, internal or external installation, material used in making the bifold doors, type of the glass as well as upgrading the locking mechanisms.

Of all these factors, the most significant influences are both the material and the number of panels to be used. For bifold doors with 3 panels, the potential cost will range from £1,200 to £2,500 depending on the materials used, be it aluminium, timber or uPVC. For a 4 panel bifold door, the price will range between £1,400 to £2,800 depending on the either of the three aforementioned materials. And finally, for a 5 panel bifold door, the cost will be between £2,500 to £5,500, also depending on the three materials.

When calculating the cost of bifold doors, it’s also important to factor in the cost of installation as the task requires specialized skills and tools, therefore it’s not advisable to be made a DIY project. The cost of installing a bifold door will also be influenced by multiple factors such as the bifold door material, the number of panels, your location in the UK, the installer of your choice as well as whether or not there’s an existing opening that’s suitable for bifold doors. The price will ultimately boil down to the installer you hire, so it’s advisable to contact multiple professionals and compare their services and quotes. For the easiest installation where there’s an existing opening in the wall, the price will range between £150 to £500. However, for more complicated installations, the price could be above £500.

How much a flat roof costs to repair depends on a few factors. Is your flat roof on a garage or an extension? What is the flat roof made from? It’s always best to get a few quotes to compare prices, but we’ll give you a rough idea here. If your flat roof was installed in the 1990s or earlier, it’s likely that you’ll see some leaks or damage soon. Felt flat roofs used to be installed completely flat, which meant that water couldn’t run off. That means that water pools and can create moss and damp. Sun exposure can also damage the felt, causing damage and eventually holes that lead to leaks. If you’re lucky enough to have got away with just needing a flat roof repair, this should set you back an average of £100 per square metre. If your roof is sagging due to the weight of it putting pressure on the timber frame, you might need additional joists – which could cost anywhere between £1,000 and £2,000, depending on how many you need. But if the problem is due to the internal part of the roof system becoming waterlogged, you could be looking at over £5,000. If your roof is severely leaking or the timber joists are rotting, it might be more cost effective to replace your flat roof. If you keep forking out for repairs, it will eventually be cheaper just to replace the whole thing, which could cost around £2,000.

How To Build A Conservatory

Conservatories are a perfect means of creating an extra living space within your home. They can serve various purposes which includes serving as an avenue to entertain guests, a playroom for the kids and can even be used as a home office, they’re able to open up your property without having to break the bank for the highly expensive renovations. So if you wish have a conservatory constructed in your home, it’s either you do it yourself or hire a professional. Doing it yourself will help you save some money but can also end up disastrous. So if you lack the confidence to undertake this project by yourself, then it’s strongly recommended that you hire a professional who can guarantee the best results. In this guide, you’ll discover all steps required to build your own conservatory.

✓ The Base. Due to its durability and cost, concrete happens to be the most used material for conservatory’s base. Firstly, measure the enough area to accommodate the conservatory. Dig at least 1 metre deep and ensure it’s level. Fill with damp membrane and pour your concrete mixture in evenly till it reaches level ground. Once done, make sure that the base is totally dry before erecting the conservatory

✓ Building. Basically you can start by constructing the walls and ensure that they’re sturdy and secure, putting into consideration their measurement.

✓ Roofing. Good news here is, DIY conservatories will already come with the roofing in place, so you won’t have to bother about this stage when building. They usually come with an acrylic roof which is easy to install and maintain.

✓ Flooring & Finishings. Starting from the roof, ensure that there’s sealant on all areas where air can pass through. For the flooring, you’ll have to choose your patio slabs or tiles to go outside of the structure. You can apply these with a thin layer of concrete or onto screed flooring.

How to repair a flat roof depends on the type of flat roof you have. We’ll talk about how to repair felt, asphalt, fibreglass and EDPM flat roofs yourself. But ultimately if you want the best finish, it’s best to ask a professional to repair your flat roof for you. Repairing a flat roof Whether you’ve got an old pour-and-roll type felt roof or a newer torch-on felt flat roof, you can get cracks, lifting around joints, leaks or dips. As a temporary measure, you can buy a special paint that you paint over cracks. For a more permanent repair, you can add a patch of torched-on felt or add a layer on top. Asphalt flat roof repair As your asphalt flat roof gets older, you may notice blisters, cracks or shrinkage and sagging around flashings. Again, you can use a paint on fix from a tin as a temporary repair, or add heat-applied flashing tape around flashing. For a more permanent fix you can use a liquid system, but many are only available to the trade market. You can also add a patch of torched-on roofing felt over a crack. How to repair a fibreglass (GRP) flat roof Fibreglass flat roofs are usually excellent, but problems can involve leaking flashing and cracks near upstands, trims or board joints. You can add acrylic sealant to cracks or holes for a good DIY repair, but a flashing problem is more difficult to fix. You’ll need to clean and sand the affected area of flashing, then laminate a 600g chopped strand mat into place, cure it and add a topcoat colour to match the roof. That sounds like a job better left to a specialist. EDPM rubber flat roof repair Rubber roofs often suffer from shrinkage when mechanical fixings haven’t been used near upstands, flashing leaks or holes or cuts. If you’ve got a small tear that you want to repair, you can add some lap sealant to the area – but use it sparingly. For a more permanent repair to flashing, buy some self-adhesive flashing that will mould into shape easily. Clean the area you want to repair, add EDPM primer, then stick the patch of flashing on from the centre outwards with a hard roller. You can add lap sealant around the edges if you want more protection from water.

There’ll certainly come a time in which even the neatest and tidiest of homes will do just fine with a good deep cleaning. As a pretty tedious task which can easily become overwhelming, it’s always helpful to break the tasks into smaller and more manageable tasks. This guide will show you the best approach to take to have your residential property deep cleaned. However, if you are not confident enough to pull this off, we’d strongly advise that you get in touch with a professional domestic cleaners who can help guarantee the best results and also save you some time as well as money that could result from costly errors or accidents.

• Dust your house. Dust each and every single room of your house, including the topsides of all furnitures, the undersides of the shelves as well as the handrails, picture frames, TV screens and knickknacks. It’s always better and easier to dry dust, but you can also dampen a microfibre cloth with warm water to get rid of stubborn stains.
• Clean furniture fabric. Neaten the pillows and furniture blankets, strip and remake beds. Also, brush the furniture surfaces using a vacuum extension as required.
• Clean the mirrors and glass. Use a soft and clean cloth (both wet and dry) to wipe down mirrors and windows throughout the house.
• Clean surfaces. Wipe all surfaces throughout the house and disinfect as needed. Ensure to clean all surfaces that the fingers touch like door handles, light swtiches, TV remotes and the likes.
• Clean the kitchen and bathroom. Spray cleaner on sinks, tubs and toilets and leave for some minutes before coming back to scrub. Wipe down the microwave, cabinet and appliance doors in the kitchen.
• Clean floors. Sweep and mop or scrub the floors as required.
• Vacuum the house. Make sure that all the necessary areas are well vacuumed.

If your solar panels are mounted on your roof and you require a ladder to reach them we would always recommend you get a professional to do the work for your own safety.

Generally, 4-yard skips are basically designed for small clean or clear out projects or residential use. If you want to carry out a small renovation task or to clear out your home, you simply can not ignore the disposal of your unwanted waste. You’ll save yourself some time, money and potential accidents by hiring a 4-yard skip that will do the job effectively. We are all aware how time consuming it is making several trips to the local waste disposal centre.

When talking about the size of a 4-yard skip, it runs beyond its capacity. Skips of small sizes can be easily accommodated in not too large spaces which can be in the garden or driveway which saves you the stress and money of having to acquire skip hire permits.

If you’d like to know the the size of a 4 yard skip in metres, we’ve got you fully covered for both imperial and metric! The answer is provided below:

Imperial - Width 4’3, Height 3’2

Metric - Width 1.29m, Height 0.972m

It is, however, important to take note that when hiring a skip the measurement might be a bit tricky. The ‘4 yard’ term implies the capacity of the skip and not the length. The actual length of a 4 yard skip is only 6 feet or 2 yards. As a result, before you hire a skip, there’s the need to be clear as to the measurement you’re looking for. Otherwise, you might end up hiring the wrong skip and having to get another. Not good for your pocket, right? Well, that’s why we’ve provided this answer to help you in the best possible way! Click here to learn more about skips.

It depends on the style and size of the conversion, but in general, a loft conversion will take between 1-2 months. A loft conversion is a substantial building project, and plans will need to be drawn up. This may add to the time it takes to complete your loft conversion.