Find a Shop Fitter you can trust in Newtownabbey.

How To Lay Block Paving

Do you wish to know how to install block paving? We’ve got you covered! Here, you’ll find a useful step by step guide that’ll provide you with all the necessary information to lay a wide range of block paving products available in the market today. You must, however, note that the installation of block paving can be a tricky affair and should not be attempted unless you have undergone a proper training or have a good experience in the field. If otherwise, we’d advise you to leave the task for a reliable block laying professional to guarantee the best results and also avoid making costly mistakes.

lDesign

• Draw up a design to perfectly suits your needs.

• Decide on the type of block as well as colour.

lExcavation

• Use a mini excavator or a JCB ( depending on the size of the job) to excavate the driveway.

• Identify and mark out the area to be excavated.

• Dug out the area until you reach a suitable level

• Ensure that the proposed finish level is 150mm underneath the damp proof course in any of the adjoining building’s brick.

lEdge Restraints

• Build a 100mm depth-thick concrete foundation with the help of a concrete mixer, 1 part cement and 6 parts ballast.

• Position the kerb unit on top of the level with a string line and spirit level.

• Use a trowel and rubber mallet to mortar the kerb unit to the foundation.

• Haunch the back of the kerb units in such a way that the concrete reach half way up the kerb’s rear.

lSubbase

• Put the crushed concrete in the edge restraints and ensure it’s at the desired level of 50mm.

• Use a vibrating plate to compact and level

lScreeding

• Apply a layer of sharp sand (to 50mm depth) and campact it using a vibrating plate.

• Apply second layer of sharp sand (to 20mm depth) on top of the first layer.

• Level the second layer to the correct falls.

lInstallation Of Paving

• Lay the block paving starting from the bottom of a slope.

• Ensure the blocks are placed at about 10mm to 15mm above the required finish level.

• Make sure the blocks used are between 3-5 packs as you proceed with your desired pattern. You may need to cut smaller block pieces to fill smaller gaps.

lFinishing Touches

• Clear out the area to ensure no debris is left on the blocks.

• Put kiln dried sand and brush across the whole of the area, ensuring the sands falls between the blocks’ joints.

• Compact the drive with the vibrating plate.

• Brush more kiln dried sand over the area and compact again

• Repeat the process until the joints are full of sand.

The quick and simple answer to this question is yes, you can definitely spray upvc window with a different colour. In fact, this represents a much more cost effective mean of changing the upvc windows colour. Back in the days people used to simply replace their upvc windows, doors, fascias, gutters, garage door conservatories and the likes which is actually a much costlier option.

Generally, upvc window frames are known to have a lengthy lifespan, however the common misconception is that the colour you pick originally and install is the colour you’d have to keep till you have them replaced. Typically, people will have white upvc windows, however in recent times there has been more colours coming on in the market such as anthracite grey, black, brown and many more when it comes to replacing. However, replacing your upvc window frames come with a greater associated expenses, building works, a lot of hassle as well as mess. As a result, there has been a significant increase in the number of people looking for upvc painting and recoloring as this costs a lot less than replacing existing frames up to 80% in several cases. From the savings that’ll be made by spraying and painting upvc window frames, it makes absolutely little sense replacing the frames. Therefore, it’s highly recommended to have your upvc windows sprayed and painted by an experienced professional who can guarantee the best results the first time.

1. Remove fascias and trims Unscrew or prise off the screws and nails fixing the trims and fascias to your shed.
2. Take off doors and remove windows Unscrew hinges from doors and take them off. Remove all metalwork once the door is off. If you’ve got frames on your windows, unscrew these, and remove the panes. Be extra careful if your windows are made of glass.
3. Take off the roof Prise off the tacks from the roofing felt and take the felt off – you can’t reuse it, so you’ll need to throw it away. Unscrew the screws on the roof boards and slide them off the shed’s frame – you might need a friend to help you do this.
4. Take out the roof brace (optional) If your roof has a brace, unscrew the brackets that hold it to the side of the shed. Remember not to lean on anything once you’ve taken the brace off as the walls might be wobbly.
5. Unscrew the frame from the floor Remove all the screws that are holding the shed to the base, remembering not to lean on the walls.
6. Unscrew the frame corners Starting at the corner of the front gable, remove the screws where the panels meet. Once a panel is free, lift it carefully out of the way so you can carry on with the others.

To ensure that your boiler is safe and operating efficiently, it’s essential to have it serviced on a regular basis.

Generally, a boiler service will deliver a wide array of benefits which includes the opportunity to identify safety issues like a possible leak of carbon monoxide, efficient use of energy and reduction in energy bills, prevention of breakdowns, a valid warranty when the boiler is serviced regularly by a qualified engineer as well as an extended lifespan. So what exactly does a boiler service cover? This guide will give you a good insight as to what happens during that service.

Before we get started, it’s very important to note that the work done is always as good as the engineer you employ. Therefore, it’s advisable to make sure your preferred engineer is qualified before proceeding with the service. Below are some of the basic practices the engineer may perform during their visit.

• Thorough Inspection

During the visit, the engineer will carry out a detailed examination of your boiler to ensure it still meets the current standards while also making sure that there are no leaks or corrosion. What’s more? They’ll also examine the boiler’s flame for any faults.

• Boiler Casing Removal

The boiler casing will be detached to check all components and ensure they’re free from all forms of dirt and see to it that they’re all working just as they should. This will include examination of the heat exchanger, main injector, burner and spark probe.

• Flue Examination

The engineer will inspect the flue terminals to make sure there are no form of obstructions and it’s also safely installed.

• Gas Pressure Examination

This is done to make sure the heating system is operating at the right pressure.

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

Aluminium windows have a range of benefits that make them a great alternative to uPVC windows. Developments in technology have meant that modern aluminium windows now have the same energy efficiency levels as uPVC. Plus, their strength and flexibility make them a more attractive choice to many homeowners, particularly for more modern buildings.

Aluminium frames are typically much thinner than uPVC frames, allowing more light in and wider views. The metal can also be moulded to suit custom shapes, making it ideal for unusually shaped windows. Aluminium windows are available in lots of different colours, so can be designed to suit a wide range of interiors and exteriors.

You’d have probably heard of the positive impact of air conditioning systems in work environment, but if you’ve never experienced it or reaped the benefits as a business owner then it’s possible to remain unconvinced. If you’re a business owner thinking about making an investment in heating and cooling systems, then you’ve come to the right place! The short and simple answer to this question is yes, an air conditioning system will definitely help improve staff productivity.

In this post, we’re going to consider a number of ways in which an AC system can help improve the efficiency and productivity of employees in a work environment. Let’s take a look!

• It saves time. One of the biggest factors resulting in reduced employees’ productivity is wasted time. For instance, when the office is hot the workers tend to spend more time adjusting fans to cool off or getting water which implies less time to get the daily tasks done. Installing an AC system can help buy you back hours of productive work from your staff.
• It keeps them focused. When the temperature is too hot, employees tend to get both physically and mentally sluggish. Consequently, they’d have problems focusing on the job at hand which leads to silly mistakes and hard times solving basic issues. With an air conditioning system, you can help your employees increase their speed while also enabling them to think, move and work efficiently.
• It helps to decrease stress levels. In the modern era where the work environment is ever-dynamic and fast-paced, there’s the need to help your staff cool off if you wish to get the best output from them and that’s where an air conditioning system comes in.

Should A Professional Replace My Conservatory Roof?

As your first and primary line of defence against the harsh weather conditions or elements, there’s the need for your conservatory roof to be in pristine condition at all times. This will enable it to keep your conservatory safe and dry, while also helping to protect its structural integrity. When you have a reliable roof over your head, your conservatory will be free of any weather-related damage. Consequently, highlighting the importance of regular maintenance of your conservatory roof.

However, over the years, there’ll come a time whereby maintenance and repairs will no longer be a wise decision. When this occurs, you know it’s high time you replace your conservatory roof to continue enjoying the structure’s numerous benefits all year round. Getting a professional to replace your conservatory roof is crucial for several reasons, let’s have a look!

✓ Knowledge and expertise. Conservatory roof installation experts are well trained and also possesses the required knowledge to work at height while also being able to guarantee the best results which will save you both time and money.

✓ Giving your conservatory a new look. Replacing a conservatory roof isn’t as simple as it seems. Trying a DIY without prior experience and knowledge can end up disastrous and making the new roof even more unsafe and unappealing than the old roof. When done by a professional who knows his way around the roof, you can be rest assured that your new conservatory roof will come out picture perfect.

✓ Saves you money and time. What would take a professional just a couple of days to complete is most likely to take a DIYer several weeks to get done and more often than not, end up with a disastrous result. To save yourself the stress, time and money, calling in a professional is your best bet.