Find a Roofer you can trust in Huddersfield.

How to repair a flat roof depends on the type of flat roof you have. We’ll talk about how to repair felt, asphalt, fibreglass and EDPM flat roofs yourself. But ultimately if you want the best finish, it’s best to ask a professional to repair your flat roof for you. Repairing a flat roof Whether you’ve got an old pour-and-roll type felt roof or a newer torch-on felt flat roof, you can get cracks, lifting around joints, leaks or dips. As a temporary measure, you can buy a special paint that you paint over cracks. For a more permanent repair, you can add a patch of torched-on felt or add a layer on top. Asphalt flat roof repair As your asphalt flat roof gets older, you may notice blisters, cracks or shrinkage and sagging around flashings. Again, you can use a paint on fix from a tin as a temporary repair, or add heat-applied flashing tape around flashing. For a more permanent fix you can use a liquid system, but many are only available to the trade market. You can also add a patch of torched-on roofing felt over a crack. How to repair a fibreglass (GRP) flat roof Fibreglass flat roofs are usually excellent, but problems can involve leaking flashing and cracks near upstands, trims or board joints. You can add acrylic sealant to cracks or holes for a good DIY repair, but a flashing problem is more difficult to fix. You’ll need to clean and sand the affected area of flashing, then laminate a 600g chopped strand mat into place, cure it and add a topcoat colour to match the roof. That sounds like a job better left to a specialist. EDPM rubber flat roof repair Rubber roofs often suffer from shrinkage when mechanical fixings haven’t been used near upstands, flashing leaks or holes or cuts. If you’ve got a small tear that you want to repair, you can add some lap sealant to the area – but use it sparingly. For a more permanent repair to flashing, buy some self-adhesive flashing that will mould into shape easily. Clean the area you want to repair, add EDPM primer, then stick the patch of flashing on from the centre outwards with a hard roller. You can add lap sealant around the edges if you want more protection from water.

The cost for a sun tunnel is affected by 5 key factors:

1. Tube size: Small areas or stairways can gain from a 10-inch size tube, whilst bigger rooms will require a bigger tube. The higher television size, the greater the price.
2. Kind of tunnel and also roof type: You can pick from stiff or flexible tunnels and also domed or flat roofing system panels. Each choice will have a different price.
3. Place: Where you stay in the country will certainly impact the price of your sun tunnel installation. Generally, the higher the living prices in your location, the greater the price of employing an expert will certainly be.
4. Length of the tunnel: Longer tunnels will be charged at a greater price than their shorter equivalents so whether the tunnel runs from the roof to the 2nd or very first flooring will certainly impact the sun tunnel price.
5. Ease of gain access to: Flexible tubes are fantastic for homes where sun tunnels do not run in a straight line from roofing to ceiling. The tubes can then be fitted around challenges in your loft space. Frustratingly, these alternatives do not allow as much light as stiff tubes and also due to their hard setup can be much more expensive.

A pitched roof is a type of roof that is defined to have a sloping surface that has an angle that is greater than 20 degrees. Pitched roofs offer a more classical appearance. They remain the most communal and effective answer in wet and cold weathers to guarantee all-out protection.

Eaves

In the roof, the lower part of the inclined roof which is prominent outside the external face of the wall. The chief purpose of eaves is to pour the rainwater from the roof straight on the exterior wall. It also provides protection from sunlight. Eaves are sometimes decorated to an architectural beauty.

Gable

The Three-sided higher part of the wall at the end of a ridge roof.

Flashing

A band of impermeable material, typically metal, used to eliminate water from the intersection between a roof covering and another part of the structure. Flashings are provided to stop moisture from inflowing the wall and roof through joints in copings, parapet wall, and other infiltrations through the roof plane.

Hip

The Hip is defined as the exterior angle, which is generally greater than 180 degrees, which is formed at the inclined ridge of the roof slopes.

Ridge

The ridge is defined as the horizontal intersection made by the rising roof surfaces that are inclined in opposite directions.

Purlins

Purlins are the horizontal members which are laid on the principal rafters which help to support the common rafter of a roof. This is usually done when the span is large. Purlins are made from wood or steel. The top surfaces of the purlins intend to be unvarying and plane.

Fascia

This is the wooden board that is fixed to the feet of the common rafter at eaves. The Fascia helps the lowest ends of the roof covering material to rest on it.

Rafter

One of the major structural components of a pitched roof is a rafter. The rafter generally begins for the support of the roof to the ridge or hip. The purlin is supported by equally spaced rafters used side by side.

How Much Does Roof Repair Cost?

With the typical British weather, the roof is always subjected to enough battering every single day. With that type of events, you’d expect to find some chimney pots on the floor or roof tiles to go missing every once in a while. When these minor roof issues occur, a professional roofer is always in hand to easily resolve these problems. However, there are times in which the roof will be in a terrible condition with persistent leaks which is beyond the capacity of a roofer to resolve. In such cases, you may have to consider having the roof replaced as the best choice.

If you’re currently facing some issues with your roof and you need it repaired, then you’d probably want to know just how much it’ll cost to complete the project. In the UK, a roof repair cost can be within the range of £100 to £12,000 based on a number of influencing factors such as where the property is located as well as the size of the property. For instance, if you happen to stay in London where the demand is higher and there’s also the high cost of living, roof repair costs tend to be a bit more costly.

Let’s look at a simple breakdown of some roof repair jobs. These includes the following:

✓ Cost of renovating the roof on a detached four bedroom house using slate ( two story house) will range between £6300 to £12000.

✓ Cost of renovating the roof on a two story semi detached house using slate will range between £5000 to £7400.

✓ Cost of renovating full roof on a two bedroom bungalow using slate will range between £4000 to £5900.

How To Replace Flat Roof Felt

Also referred to as tar paper, roofing felt is installed underneath the roof’s shingles to help deny water access to your home. Installing the roofing felt in overlapping layers builds a water barrier in situations whereby the weather damages or blows away the shingles. Although the application of a roofing felt on a flat roof is relatively easier and safer than working on a peaked roof, it’s advisable to take enough care and precautions. If you lack proper training and experience for this task, we’d recommend you employ a reliable professional to guarantee the best results and save you from further headaches especially in cases whereby unfortunate errors are made. This step by step guide will give you a good insight into the flat roof felt replacement process.

• Take a measurement of the width and length of the roof.

• Calculate the square footage by multiplying the numbers.

• Multiply the square footage gotten by three (it’s advisable to install three layers of roofing felt to create a really strong weather barrier).

• Use a claw hammer to remove the existing roofing felt.

• Use utility knife to cut the new felt to fit the length of the roof.

• Place the first piece along the roof’s edge and use a hammer tacker to tack the felt in place with staples or galvanized nails and hammer.

• Put the staples or nails at every 6 inches along the side touching the roof’s edge as well as down the short sides.

• Repeat the same process for the second piece, laying it out beside the first row of felt.

• Cut a piece of felt to the appropriate length using a utility knife to begin the second layer of roofing felt, and cutting it in half, lengthwise.

• Apply construction adhesive along the first row using a trowel.

• Press the first piece for the second layer onto the adhesive. Repeat this process until the roof is covered with a second layer

• Apply construction adhesive over the second layer to install the third layer. Begin with a full piece of felt without cutting it in half.

• Overlap each piece by 2 inches until you’ve completely installed the third layer.

How To Clean And Maintain Metal Roofs

If you already have a metal roof or just planning to get one, you’d probably be interested in knowing the cleaning and maintenance procedures. Although, metal roof are widely known to be very easy to clean and maintain and also very durable and long lasting, it’s still strongly recommended that homeowners should do all in their power clean and to take care of their metal roof in order to ensure it they live up to their potentials. Cleaning your metal roofs regularly helps to minimize damaging element such as airborne dirt, pollen, organic material debris, pollution, mildew and lots more. If left unattended to, these unwanted elements can result in several negative issues over time as such as chalking. Due to fact that metal roofs normally features special coatings as well as paint, cleaning the roof is both easy and environmentally friendly, which removes the need to use toxic chemicals. With just plain water, you can effectively wash down dirt, dust and other debris from your metal roof.

While the cleaning process is quite simple, working at height can be incredibly dangerous. It requires skills and confidence, so if you lack either of these qualities, it’s advisable to call in a professional roof cleaning contractor for help. Below is a simple cleaning solution usful for most metal roofs.

✓ In the event whereby water alone isn’t enough, make a cleaning solution using a quarter cup detergent ( which should include car washing soap, mild laundry detergent, mild dish soap) for each gallon of water.

✓ Apply the mixture to the surface of the roof with a wash cloth and ensure to the application gently.

✓ After application, allow it sit for up to 15mins.

✓ Rinse the roof surface with plain water.

A Velux window is a brand of roof window, but the brand is so popular that people often use the name to describe the entire type of window. They are windows that are installed at the same orientation and ‘in plane’ with the surrounding roof, and they’re usually installed at a minimum of a 15-degree pitch. You can buy roof windows that offer completely frameless internal views for a really clean look in your loft conversion, while some come with built-in shutters.

Velux windows aren’t to be confused with rooflights which usually refers to a glazed unit that’s installed on a flat roof. It might also mean a window that’s been installed on a pitched roof out of plane with the level of the tiling.

People also confuse roof windows with skylights, which normally can’t be opened or closed and are usually smaller than Velux windows. Skylights, therefore, only let daylight into the room whereas roof windows also help with ventilation.

If you’re using your loft as a room in your home rather than simply for storage, you must have a roof window installed. Skylights won’t be enough as they don’t allow for ventilation. It doesn’t have to be a Velux window – it can be any type of roof window. Luckily, they tend to come in standard sizes and they must be CE marked if they’re sold as a roof window, so they should be easy to find.

How To Replace A Broken Roof Tile?

If you have a broken roof tile on your property, the next logical step to take is having it replaced as soon as you can. However, this is not the simplest of tasks so you might need some guidance if you wish to do it yourself. If you lack the confidence needed to pull this off as it involves working at height, then we’d strongly recommend you hire the services of a reliable roofing contractor or company who can guarantee the best results for help. In this guide, we’re going to walk you through the processes involved in the replacement of broken tiles. Let’s have a look!

✓ Match your roof tiles perfectly. The most frequently used roof tiles are concrete and terracotta. They may look all similar but they can actually vary in shapes, length as well as thickness. To replace a broken tile, you must first make sure that it’s the same type of tile so it doesn’t interfere with the flow of your roof which can lead to further damage.

✓ Climb on to the roof. Make use of a strong and stable ladder to do this. If you’re not comfortable with heights, simply call in a professional. Falling of the roof would be more expensive.

✓ Remove the broken tile. Lift up the overlapping tile next to the broken tile in such a way to enable an easy removal of the broken one. If you’re not able to life them, then they probably have nails securing them in place. Remove these nails to proceed.

✓ Replace the broken tile with the new one. To do this, simply lift up the bottom tiles from the above row and then slide the new tile back in place. If the tiles have been nailed, make sure you also drive a nail through the hole in the new tile into the timber roof batten.