Find a Roofer you can trust in Leiston.

Velux windows actually refer to one brand of roof window, which are windows that sit in your roof space and allow light and ventilation into your loft. But how do you install a Velux window? If you’re a competent DIYer, it’s not as difficult as you might think.

You can normally install roof windows entirely from the inside, so you don’t need to get up on your roof or hire costly scaffolding. They come with detailed installation instructions, so as long as you follow them you shouldn’t have much trouble.

Before you start, you’ll need to read up on the Building Regulations and Planning Permission laws. Speak to your local Building Control department if you have any questions.

Firstly, prepare the opening by removing enough tiles or slates from the roof. There’s no need to go out on the roof – access them by cutting away the felt underneath which will give you access to the tiles and battens. Cut away one of the battens from under a tile, then you can slide all the tiles into the roof space. You’ll need to cut away the roof timbers to make the right size opening, then add more timbers to strengthen the ones that are left.

Next, remove the opening sash from the new roof window then fit the frame into the new opening using the brackets provided with the window. Then fit roof flashing between the new window and the roof so you don’t get any leaks. Then lay your tiles back in position around the new Velux window; you’ll probably have to cut some to shape which you can do with an angle grinder. Always cut them on the ground, not in position on the roof.

Lastly, fit the sash back onto the window and you’re done!

If this sounds like too much hard work, plenty of window installers will be able to help you fit a Velux window and will probably be able to provide a much cleaner finish.

Whether you’re liable for a leaking roof in a commercial property will depend on your ownership status and any contracts. Of course, if you own a standalone commercial property, it would make it your responsibility to repair to leaking roof. But if you own an office within a building, you should check your paperwork to see whether you are responsible for some or all of a leaking roof.

If you’re a tenant in a commercial property, things get a bit more complicated. Lots of commercial leases are FRI, or Full Repairing and Insuring leases, which means that the tenant is responsible for all external and internal maintenance and insuring the building. It means that it’s vital that you read through your tenancy agreement in full before signing it and seek legal advice if you think you need it. If your lease is an FRI lease, you are liable for a leaking roof in your commercial property.

It’s important to ensure that you have a schedule of condition for the property, which will mean that you only have to restore the commercial property back to the condition that it was in when you took over. It’s also worth getting the roof inspected before you sign the lease, as if there is any damage before you sign the landlord may be responsible.

The best way to avoid having to pay for a leaking roof in a commercial property is prevention. If you are liable for repairs and maintenance, make sure you have the roof inspected regularly by a reputable company to avoid having to pay for costly repairs when disaster strikes.

Blisters are most common on membrane roofing systems. Lots of contractors will tell you that if there are no signs of further damage, there might not be any need to repair flat roof blisters. They form when pockets of air or water get trapped between layers of the roof’s membrane or between the membrane and the frame. When the sun is out and it heats the pockets expand and stretch the membrane. If you do want to repair your flat roof blisters, there are a few ways to go about it.

If you have a membrane flat roof, cut away the membrane until you reach a place where the membrane is still stuck tightly to the roof. Reapply as many new membrane layers as you cut away over the blistered area. You might even need to do more. To make sure your patch remains watertight, you’ll need to leave at least 6 inches around the edges of the blister.

If you’ve got a felt roof, you can cut an X shape through the blister. Peel back the triangles that you’ve made and let the timber frame dry for a while (so don’t do this when rain is forecast!). Then, coat the area with lots of bitumen adhesive and leave it to dry until it feels tacky. Then press down the triangles of felt firmly into the adhesive.

After that, you’ll need to add more bitumen adhesive to the cuts you made. If you’ve got any spare roofing felt, cut a square that’s about 100mm bigger than the cuts then lay this over the adhesive. If you’ve not got any felt, it’s cheaper to use a self-adhesive flashing strip. Once you’ve laid the strip or patch over, seal the edges with more bitumen adhesive.

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

Tar and gravel flat roofs are popular because the gravel weighs down the surface of the roof so it doesn’t blow away and it also protects it from sun damage. The tar makes the roof watertight, so you won’t get any leaks. However, sometimes problems occur and you’ll get cracks and leaks. So how do you repair a tar and gravel flat roof?

If you notice leaking coming through your flat roof, try to find the source of the leak. Since water can travel easily, it might not be where you think it is. The first place to check is the flashing, then any parts of the roof with gravel missing. Once you’ve found the crack, sweep away any remaining gravel and clean the area.

Apply a primer to the area and allow it to dry. Then, apply a tar and gravel roof patch that you can get from most DIY shops. Patch 2-3 inches around the damaged area, creating layers, and ensuring that there aren’t any air bubbles or gaps. Then you should cover the entire patch with gravel.

Before you try to repair a tar and gravel flat roof yourself, consider how much of the roof needs repairing. Professionals often say that if cracks and faults make up 25% or more of the roof, then you should look to replace it. It might be tempting to try and replace your tar and gravel roof yourself, but it’s best left to the specialists. They will ensure that your new roof is watertight and strong enough to withstand sun damage and storms.

How To Clean Algae Off Roof Shingles

Stains and dirt on asphalt shingles can only make your entire house look shabby which can go a long way to hide away the true value of your building. In some cases, dirts and stains on asphalt roofing shingles are nothing more than a cosmetic issue. However, there are also times in which it goes far beyond this - when the stains are indicators of a problem that if ignored, can result in a serious roof damage and ultimately, roof failure. In most cases, it’s usually hard to distinguish these stains and hence, the more reason why your asphalt roofing shingles should be regularly cleaned and maintained. In this article, we’re going to look at how you can get rid of algae of your roof shingles.

Algae growth on roof usually have either blue, green or black stains. They normally begin with little spots which will develop into streaks overtime. These stains are mostly mistaken for moss or mildew and aren’t harmful to any other thing than the roof shingles. However, the look it gives the entire house is something nobody enjoys.

It should be noted that this is a task that deals with working at height and requires skills and confidence to pull off. If you lack any of these qualities, simply reach out to a professional for help.

✓ Safety first. Put on protective clothing.

✓ Apply a bleach solution with a garden sprayer and let it sit for up to 20 minutes

✓ Rinse the roof thereafter with the stream from the hose (do not use a pressure washer as it can damage the roof shingles)

✓ If there are still algae left after rinsing with water, you can make use of a brush with medium-stiff bristles to gently scrub the stains off. If some stains are still left, simply let the roof dry before repeating the process again.

How to repair a flat roof depends on the type of flat roof you have. We’ll talk about how to repair felt, asphalt, fibreglass and EDPM flat roofs yourself. But ultimately if you want the best finish, it’s best to ask a professional to repair your flat roof for you. Repairing a flat roof Whether you’ve got an old pour-and-roll type felt roof or a newer torch-on felt flat roof, you can get cracks, lifting around joints, leaks or dips. As a temporary measure, you can buy a special paint that you paint over cracks. For a more permanent repair, you can add a patch of torched-on felt or add a layer on top. Asphalt flat roof repair As your asphalt flat roof gets older, you may notice blisters, cracks or shrinkage and sagging around flashings. Again, you can use a paint on fix from a tin as a temporary repair, or add heat-applied flashing tape around flashing. For a more permanent fix you can use a liquid system, but many are only available to the trade market. You can also add a patch of torched-on roofing felt over a crack. How to repair a fibreglass (GRP) flat roof Fibreglass flat roofs are usually excellent, but problems can involve leaking flashing and cracks near upstands, trims or board joints. You can add acrylic sealant to cracks or holes for a good DIY repair, but a flashing problem is more difficult to fix. You’ll need to clean and sand the affected area of flashing, then laminate a 600g chopped strand mat into place, cure it and add a topcoat colour to match the roof. That sounds like a job better left to a specialist. EDPM rubber flat roof repair Rubber roofs often suffer from shrinkage when mechanical fixings haven’t been used near upstands, flashing leaks or holes or cuts. If you’ve got a small tear that you want to repair, you can add some lap sealant to the area – but use it sparingly. For a more permanent repair to flashing, buy some self-adhesive flashing that will mould into shape easily. Clean the area you want to repair, add EDPM primer, then stick the patch of flashing on from the centre outwards with a hard roller. You can add lap sealant around the edges if you want more protection from water.