Find a Roofer you can trust in Selkirkshire.

One of the most popular choices for roofing materials are roof slates. There is a number of advantages that a roof slate has, hey can be aesthetically pleasing, they can also increase the potential selling value of the house and many more. Slate is a sturdy and resilient material that delivers waterproofing physical characteristics to a pitched roof. Unlike other roof materials which absorb water slates do not. Therefore, slate is the most resistant towards freezing and water damage.

Find out the pitch of your roof

Before beginning with the fitting procedure, you need to figure out the pitch of your roof. The roof pitch commands how much overlap is essential with each slate. This has been made a lot easier than the early days with the advancement of technology.

Find out the required overlap

Once you’ve found out the exact pitch of your roof accurately, take a look at the slate producer’s description. Each manufacturer will propose the obligatory overlap in order to form a firm and safe slate roof.

Roll out the roof membrane

Firstly, guarantee your joists or trusses are clean of any sheards or old nails that could harm the membrane. You will now have to roll the chosen roofing membrane along the roof trusses. It is always wise to start from one of the bottom corners and keep rolling it along to the other corner.

Secure the roof membrane

Once the membrane has been moved out, use thump nails to protect one edge. You will now have to pull the membrane taut and carefully fix it into position. Do this before adding any nails across the membrane at points of intersection with the trusses for extra stability.

Batten placement

This is done to find the proper assignment of the battens. For this, you will need two full-sized slates along with an under eaves slate. Carefully position the battens on the top of the roof on the top of the overlay. Make sure not to fix them down since it will be easier to move them around and make any adjustments.

The feasibility of this will depend on the roof’s strength, in particular its load bearing capabilities. This is simply because tiles are heavier than the metal sheeting. Normally a tiled roof will need to take a load capacity of 60kg per square metre. You will need a trusted roofing company to advise on this.

Ponding is where you see pools of water appearing on your flat roof. Unless your roof is leaking or showing other signs of damage, you don’t need to replace it. When you do have your flat roof replaced, tell the contractor so they can find out the cause of the ponding.

In general, no – you don’t need planning permission for a Velux window. The Planning Portal says that you don’t need to apply for planning permission to install a roof window if the following conditions are met:

• A roof window must not protrude more than 150 millimetres above the existing roof plane
No roof window or any other alteration can be higher than the highest part of the roof or stand out above the roof ridge
• Side-facing windows must have obscure glazing to protect privacy of neighbours and, if they open, they must be 1.7 metres above the floor of the room in which they are installed

You don’t need to apply for planning permission for a roof window because they are covered under permitted development rights. However, if you’re a leaseholder or you live in a building where your local authority has made an Article 4 Direction, you will have to apply. Usually, an Article 4 Direction is made when you live in a conservation area where any external home improvements could affect the character and look of the area. Luckily, there are special Velux windows that are designed to be more likely to be accepted by your local planning authority. They’re called conservation windows and, although there’s still no guarantee that they will be accepted, they are designed to look more traditional. Even if you don’t need planning permission for your roof window, you still need to follow any relevant building regulations for your local authority. The most important parts for Velux windows are section J and section L of building regulations, which refer to energy efficiency, thermal insulation and fire protection.

How To Clean A Roof?

If you’re planning to clean your roof, but don’t know where to start, you’ve come to the right place! There are different types of roofs available in the market today and the method used in cleaning one can be largely different from the other. As a result, we’re only going to look at one of the common types of roofs you’ll find in the UK - the Asphalt shingle roof tiles. This roof type is very common and for a good reason. Not only are they visually appealing but they’re also hugely versatile by design which enables them to be adaptable to varying shapes, angles as well as forms depending on your preference or needs. With all the benefits that can be derived from asphalt shingle, they however, need to be properly maintained to help retain their good looks.

To clean your asphalt shingles, you’ll most likely require some type of chemicals especially when dealing with algae stains and some other visual problems. Therefore, make sure you purchase a product marked safe to be used on this type of roof and not those only proven to remove moss and algae stains. Mix the chemical cleaner with a gallon of water and a quart of bleach or as instructed by the manufacturer. Pour the mixture inside a pump-style garden sprayer and mix thoroughly. When done, climb up on the roof and spray as good as you can. Upon completion of spraying the roof with the mixture, then allow to work its magic for some time - about 15 minutes or thereabout should be good.

After that, you can make use of a garden hose to spray down the roof and wash down the mixture entirely. If some stains remain, use a brush to gently wipe the tiles individually.

How To Clean And Maintain Metal Roofs

If you already have a metal roof or just planning to get one, you’d probably be interested in knowing the cleaning and maintenance procedures. Although, metal roof are widely known to be very easy to clean and maintain and also very durable and long lasting, it’s still strongly recommended that homeowners should do all in their power clean and to take care of their metal roof in order to ensure it they live up to their potentials. Cleaning your metal roofs regularly helps to minimize damaging element such as airborne dirt, pollen, organic material debris, pollution, mildew and lots more. If left unattended to, these unwanted elements can result in several negative issues over time as such as chalking. Due to fact that metal roofs normally features special coatings as well as paint, cleaning the roof is both easy and environmentally friendly, which removes the need to use toxic chemicals. With just plain water, you can effectively wash down dirt, dust and other debris from your metal roof.

While the cleaning process is quite simple, working at height can be incredibly dangerous. It requires skills and confidence, so if you lack either of these qualities, it’s advisable to call in a professional roof cleaning contractor for help. Below is a simple cleaning solution usful for most metal roofs.

✓ In the event whereby water alone isn’t enough, make a cleaning solution using a quarter cup detergent ( which should include car washing soap, mild laundry detergent, mild dish soap) for each gallon of water.

✓ Apply the mixture to the surface of the roof with a wash cloth and ensure to the application gently.

✓ After application, allow it sit for up to 15mins.

✓ Rinse the roof surface with plain water.

Keeping water away from your house is of great importance and hence, the installation of a roof guttering system to serve this purpose. However, in order to perform this task effectively and seamlessly, there’s a need to clear out the clogging dirt and debris from the gutter and ensure it’s free from water-blocking obstacles at all times. Although there are a number of ways to achieve this, but the major cause of concern for several home and property owners is having to work at heights or on top of a ladder to get the job done. This is a very dangerous endeavour especially if you do not have the confidence required to pull it off. As a result, we’d strongly recommend you hire the services of a reliable professional who possess the skills when it comes to working at heights and delivering a highly effective clean. Fortunately, there are a couple of ways you can get to clean your gutters without having to climb any ladders. Let’s take a look!

• Clean the gutter with a leaf blower. Several leaf blowers feature a nozzle attachment which is made to release a narrow stream of air which is suitable for cleaning of gutters. You don’t need a ladder to do the clean as a specialized attachment is available in order to increase the blower’s reach to your roof effortlessly. The final step would be to remove any lingering leaves or twigs using a hose.
• Clean the gutter with a wet or dry vacuum. For heavier debris, you can try out a wet or dry vacuum. To reach the obstructed gutters while standing on the ground, simply get curved attachments and hoses at a local home improvement store. You may, however, need to moisten some stubborn dirt before it can be properly vacuumed or removed.after completing the vacuuming process, simply flush the gutters with garden hose waters.