Find a Roofer you can trust in Louth.

Fitting a Velux window into a slate roof is very similar to the way you’d install it in other roof types. All roof windows, whether a Velux-branded one or not, will come with detailed instructions for you to follow if you want to have a go at fitting it yourself. But here are some brief instructions to give you an idea of what’s involved in installing a Velux window into a slate roof:

1. After you’ve removed the Velux window from its packaging, remove the sash (the part that opens) from the frame, according to the manufacturer’s instructions.
2. Next, you need to prepare the opening for the window. You can often cut through the felt, remove one of the battens from under a slate, then slide all the slate tiles into the roof space. You should then make the cut 40-60mm wider than the window, cutting away roof timbers then replacing them with more around the opening to strengthen it.
3. The roof window’s bottom brackets need to be installed on one of the existing battens for the slate roof. One of the slate courses should line up 105mm below the top edge of the batten you use.
4. Then, measure from the top edge of the batten upwards to the height of the window plus 45mm. This is where the top installation batten should be installed, with an overhang of 100mm on each side.
5. Remove the course of slates below the window, trim any excess felt and fold it over the surrounding timber. This helps with waterproofing.
6. Add the insulation collar according to the Velux window manufacturer’s instructions.
7. Place the frame in the opening, adding the brackets according to the instructions. You’ll find that lots of roof windows have pre-drilled holes to make it easy for you.
8. Replace the sash and line up the hinges. Take a look at the opening at the bottom between the sash and the frame – it should be even along the entire width. Remove the sash again to fix the upper brackets according to instructions.
9. Add the underfelt collar for your roof window as instructed by the manufacturer, then replace any slates at the bottom. You might need to cut them to size.
10. Next, add the flashing according to the instructions, along with any parts that are not yet attached, including the hood section and top flashing piece.
11. Replace all the slates around the window, allowing 60-100mm of space between the course of slates above the window and the top of the window to allow for rainwater drainage. Then replace the sash into the frame again.
12. Add the vapour barrier on the inside of the window using the screws provided, then tape it to the existing vapour barrier to prevent moisture from reaching your roof structure.

And that’s it! If you think that sounds a bit complicated, ask a roofer or window installer to fit your roof window into a slate roof for you. You’ll get a better finish and you can be sure that you won’t get any leaks from a botched installation.

How To Clean A Fibreglass Roof?

If you have a dirty fibreglass roof or perhaps you’re just planning to have one installed on a newly constructed house, then you’d probably want to know the best way to have your fibreglass roof cleaned.

Generally, fibreglass roofs are of great quality and happens to be a lot more resistant to moisture, heat, water and even fire when compared to the other alternative flat roofing materials. As a result, they require just a little maintenance but this doesn’t mean they should be totally ignored. Truth be told, cleaning of a fibreglass roof is as easy as it get, however, when it comes to working at height, skill and confidence is paramount to guarantee your safety. If you lack any of these two qualities, then it’s highly recommended that you sought the services of a reliable roof cleaning contractor who can do the work safely and perfectly. If you’re able to clean and maintain your fibreglass roof as you should, you wouldn’t have to think about replacement for about 20 to 30 years.

Cleaning is simple and doesn’t take much time. Now let’s take a look at the process.

✓ Preparation. Hose down the vegetation around the area with water to protect them. Once done, mix a gallon of warm water with one quarter cup trisodium phosphate and 1 quart of bleach. Put this mixture into a garden sprayer and sweep any dirt or debris off the roof with a broom.

✓ Application. Spray the mixture over the fibreglass roof, ensuring that it gets to all the necessary corners where dirt may be hidden. Allow this applied solution to sit for up to 15 minutes to loosen the stubborn stains and dirts on the roof.

✓ Finishing. Spray cold water to wash down all the solutions. If there’s still some dirts, you can repeat the process till the fibreglass roof is entirely clean.

There is simply not one single answer when it comes to knowing how much would it cost to replace a commercial roof. Replacement costs is a variable which is dependent on several factors.

If you are looking to take a shot at guessing an estimate, you will first need to understand the what is need for the replacement.

YOUR COMMERCIAL ROOF IS AGEING

The first sign of replacement is definitely the age. Generally, roofs come with a warranty of twenty years. Based on your materials, the real lifespan for a commercial roof tends to be around 15 to 25 years. Depending on the maintenance and the materials, lifespan can be prolonged.

YOUR COMMERCIAL ROOF LOOKS TIRED

Compare your commercial property with other buildings in the area. If it looks pale and worn out in comparison, it is high time for replacement.

WATER DAMAGE

A sturdy roof should be able to withstand extreme weather conditions such as heavy rain or high winds. However, if a storm has caused significant damage to your roof, its structural integrity might be compromised. water damage is one of the most indicative signs for a roof replacement.

CRACKS AND HOLES IN ROOFING MATERIALS

Proper upkeep of the roofing materials is required for it to continue protecting your property. If you find any cracks or holes, bent tiles or sheets, replacing them is advisable.

SAGGING COMMERCIAL ROOF

Roof replacement is critical when your roof suffers from sagging or corrosion. Once sagging or corrosion begins, the structure becomes vulnerable to damage.

Keeping all the above factors in mind, replacing your commercial roof can range from anywhere around £10,900 to £44,000 depending on the materials you choose. Materials are available in the market from £35 to around £75 per square meter. If you chose higher or premium quality materials, price can range from £115 to £200 per square meter.

While it sounds like it could be difficult to plasterboard around a Velux window, it needn’t be. As long as you have the right tools and materials, you should be able to plasterboard around your roof window easily and make good ready to be skimmed. When you or a tradesperson has fitted your Velux window into your roof, you’ll probably need to plasterboard over it to create a good ceiling. To do this, you’ll need:

• Plasterboard sheets – make sure you measure your room so you know how much you’ll need
• Screws to secure the board in place
• Drill
• Hammer
• Straight edge and pen knife to score the board before trimming
• Fine toothed saw the cut the plasterboard

When you’re ready to plasterboard around your roof window, make sure you’ve cleared enough space to work in. Then you can begin by cutting your plasterboard to size using your straight edge and pen knife to score, then your saw to get a clean cut. A common way of plasterboarding around your Velux window is to use the groove on the window frame to hold one edge of the board, then screw the other edge to the battens on the ceiling. People often use drywall screws these days as they have a better grip of the plasterboard as they drive through. You’ll need to use a drill to screw these in. However, you could use plasterboard nails, which are galvanised to stop rusting. When you’ve done this, you can then skim the walls or ask a plasterer to do it for you. Plastering, while it looks easy, is a tricky skill so it’s always best to ask a professional to do it.

In general, no – you don’t need planning permission for a Velux window. The Planning Portal says that you don’t need to apply for planning permission to install a roof window if the following conditions are met:

• A roof window must not protrude more than 150 millimetres above the existing roof plane
No roof window or any other alteration can be higher than the highest part of the roof or stand out above the roof ridge
• Side-facing windows must have obscure glazing to protect privacy of neighbours and, if they open, they must be 1.7 metres above the floor of the room in which they are installed

You don’t need to apply for planning permission for a roof window because they are covered under permitted development rights. However, if you’re a leaseholder or you live in a building where your local authority has made an Article 4 Direction, you will have to apply. Usually, an Article 4 Direction is made when you live in a conservation area where any external home improvements could affect the character and look of the area. Luckily, there are special Velux windows that are designed to be more likely to be accepted by your local planning authority. They’re called conservation windows and, although there’s still no guarantee that they will be accepted, they are designed to look more traditional. Even if you don’t need planning permission for your roof window, you still need to follow any relevant building regulations for your local authority. The most important parts for Velux windows are section J and section L of building regulations, which refer to energy efficiency, thermal insulation and fire protection.

It can be easy to repair a felt flat roof depending on the problem. If you’ve got an old-style pour-and-roll felt flat roof, you might be starting to run into problems, but even if you have a newer torch-on felt roof, issues can occur. You might find cracks, lifting, leaking flashings or dips and hollows in the felt. Luckily, there are some easy fixes – but the best thing to do to prolong the life of your felt flat roof is to get a professional to look at it.

If your felt flat roof only needs a small repair, you might be able to get away with using a paint-on fix from a tin that you just brush on. However, if you want a more permanent fix, you’ll need a few more tools and supplies.

You can use a patch of torched-on roofing felt over the crack or leak, but if your flat roof is very damaged or wet it might not take it. You can also buy liquid systems for felt roofs, but again, there is a possibility that your roof might not take it. Also most of the high-quality liquid systems are only available for trade customers, so you might be better off asking a roofing pro to do it for you.

Chimney liners are a very important component of the chimney, but the fact is most home and property owners either continue to overlook them or aren’t even aware of their existence. This is, however, quite understandable given the fact that they usually last a long period of time – more than 50 years. To ensure that they last that long, the question that arises is, do chimney liners need to be swept and cleaned? The short and simple answer to this question is yes, chimney liners definitely needs to be cleaned on a frequent basis. A chimney liner happens to be an essential part of your chimney. When it’s not cleaned, it tends to accumulate dust, soot and dirt which can give rise to a number of problems you’d rather want to avoid. Chimney liner are able to provide adequate protection to your flue but even at that the water, creosote and other contaminant build up can make the liner to deteriorate, and making it unsafe for usage. In other words, contrary to several belief, chimney liners do need the same amount of cleaning as chimneys without liners. Failure to sweep your chimney liners can give rise to the following problems:

• Creosote buildup. If your main source of fire is wood, then you’ll definitely have creosote present in your chimney. This is highly combustible and its buildup may lead to fire outbreak.
• Carbon monoxide poisoning. Carbon monoxide is said to be on the rise by NCBI and its primarily generated from heating systems which are terribly ventilated as a result of uncleaned or dirty chimneys.

To find a commercial roofer near you, you could ask other tenants or property owners whether they can recommend a company. If you choose a company that’s been recommended to you, make sure you do your own research into them before you decide to engage them; you can check whether they have social media pages, reviews and examples of previous work. If the company has a Quotatis profile, you’ll find genuine reviews from their customers there, including photos of work they’ve completed.

Another option is to do your own search online. These days lots of companies will have their own website and you may be able to make an enquiry through there without even having to call them. Again, you should always check out their qualifications, previous work and reviews before deciding to go with them.

Or, you could let Quotatis do the work for you. Simply tell us about your commercial roofing project and where the property is and we’ll put you in touch with up to 4 reputable commercial roofers that will be able to offer you a free, no-obligation quote. You can check out their reviews, qualifications, insurance and photos of work on their profile which we’ll send to you in an email when we’ve matched you. The roofing companies should contact you first, but if they don’t we’ll give you all their details so you can introduce yourself.