Find a Roofer you can trust in Bodorgan.

How To Replace Flat Roof Felt

Also referred to as tar paper, roofing felt is installed underneath the roof’s shingles to help deny water access to your home. Installing the roofing felt in overlapping layers builds a water barrier in situations whereby the weather damages or blows away the shingles. Although the application of a roofing felt on a flat roof is relatively easier and safer than working on a peaked roof, it’s advisable to take enough care and precautions. If you lack proper training and experience for this task, we’d recommend you employ a reliable professional to guarantee the best results and save you from further headaches especially in cases whereby unfortunate errors are made. This step by step guide will give you a good insight into the flat roof felt replacement process.

• Take a measurement of the width and length of the roof.

• Calculate the square footage by multiplying the numbers.

• Multiply the square footage gotten by three (it’s advisable to install three layers of roofing felt to create a really strong weather barrier).

• Use a claw hammer to remove the existing roofing felt.

• Use utility knife to cut the new felt to fit the length of the roof.

• Place the first piece along the roof’s edge and use a hammer tacker to tack the felt in place with staples or galvanized nails and hammer.

• Put the staples or nails at every 6 inches along the side touching the roof’s edge as well as down the short sides.

• Repeat the same process for the second piece, laying it out beside the first row of felt.

• Cut a piece of felt to the appropriate length using a utility knife to begin the second layer of roofing felt, and cutting it in half, lengthwise.

• Apply construction adhesive along the first row using a trowel.

• Press the first piece for the second layer onto the adhesive. Repeat this process until the roof is covered with a second layer

• Apply construction adhesive over the second layer to install the third layer. Begin with a full piece of felt without cutting it in half.

• Overlap each piece by 2 inches until you’ve completely installed the third layer.

In general, no – you don’t need planning permission for a Velux window. The Planning Portal says that you don’t need to apply for planning permission to install a roof window if the following conditions are met:

• A roof window must not protrude more than 150 millimetres above the existing roof plane
No roof window or any other alteration can be higher than the highest part of the roof or stand out above the roof ridge
• Side-facing windows must have obscure glazing to protect privacy of neighbours and, if they open, they must be 1.7 metres above the floor of the room in which they are installed

You don’t need to apply for planning permission for a roof window because they are covered under permitted development rights. However, if you’re a leaseholder or you live in a building where your local authority has made an Article 4 Direction, you will have to apply. Usually, an Article 4 Direction is made when you live in a conservation area where any external home improvements could affect the character and look of the area. Luckily, there are special Velux windows that are designed to be more likely to be accepted by your local planning authority. They’re called conservation windows and, although there’s still no guarantee that they will be accepted, they are designed to look more traditional. Even if you don’t need planning permission for your roof window, you still need to follow any relevant building regulations for your local authority. The most important parts for Velux windows are section J and section L of building regulations, which refer to energy efficiency, thermal insulation and fire protection.

A leaky flat roof is one of those things every home and property owner would rather prefer to avoid. Not only can it be extremely frustrating to deal with, but it can also have a grave impact on the overall integrity and value of your property especially when things are not done properly. Generally, all leaky roofs pose serious problems, however, a leak in a flat roof is even a lot more complicated. Ranging from the quite simple repairs to the incredibly complex fixes, flat roof repair (also known as low slope roof repair) is be seriously problematic and at times, can call for a reconstruction which involves complicated roof insurance as well as an experienced professional support.

Flat roof repair consists of many different types. Cap sheet roofs possess layers of material glued together with hot asphalt, including a roll of mineral surface glue using asphalt to the top rather than gravel. The tar and gravel roofs also possess layers of material glued together with the help of hot asphalt, with the use of asphalt on top as well as gravel included in the asphalt. A modified bitumen roof possesses more strength when compared to a cap sheet roof or the conventional tar and gravel roof. This can be 2 or 3 plies, smooth or with a mineral surface, torched on, mopped on or self adhering. What’s more? A TPO roof is a single ply roof which is usually heat welded together. A PVC roof is also a single ply roof that’s heat welded together while an EPDM is a single ply roof that’s glued together. The foam roofs as well as various coatings are incorporated to reflect the sun’s UV rays and also to maintain and seal the roof.

Fibreglass, or GRP, flat roofs are very durable and should last you years, but over time they can become brittle and you might see some cracks or holes forming. Luckily, you can repair a fibreglass flat roof and it doesn’t have to be too difficult. Cracks in a fibreglass flat roof If you notice long cracks in your fibreglass roof, you can often use a fibreglass crack sealant. Simply clean the area, squeeze the sealant into the crack, then smooth it off. If you want it to look neater, you could coat the entire roof with a restorative coating which will make it look new again. Hole in a fibreglass roof If you notice a hole in your fibreglass flat roof, you’ll want to get this repaired as soon as possible to avoid any rainwater getting into your home. There are lots of fibreglass roof hole repair kits on the market, both online and in DIY stores, so you shouldn’t have trouble picking one up. They usually contain a mouldable UV cured patch that you can stick onto the hole. It will harden and become instantly weatherproof, so is the perfect emergency repair solution. Fixing pin holes in a fibreglass flat roof Unfortunately, if you find pin holes in a fibreglass flat roof it’s often because the installer didn’t use enough resin during the fibreglassing process. Luckily, if you can’t get back in touch with the installer or you only notice after a few years, you can fix this yourself. Sand down the roof back to the clear resin layer. Clean the entire roof with acetone and reapply some GRP roofing resin. Ensure that all the pinholes are filled – you might need two coats.

Yes – you can repair a flat roof in the winter. Contractors will still be able to help you repair leaks, and it’s a myth that they will charge more. Most won’t have any additional costs just for coming out in the winter.

You'll have to wait for any snow and ice to melt before you can repair your flat roof. Depending on what type of flat roof you have, some repairs might have to wait until temperatures reach a certain level above freezing – some coating products won’t adhere (stick) in low temperatures, but a roofing professional will be able to advise you on what is best to use in the winter. If you have an EDPM rubber roof, most of the adhesives won’t mix in cold weather, so you might have to wait until temperatures rise to get a proper repair to your flat roof.

The best way to avoid needing to repair your flat roof in the winter is to inspect it at regular intervals. During the summer, even in the UK’s mild weather, the sun’s UV rays can damage and weaken flat roof surfaces, potentially causing cracks and holes. As autumn approaches, take a look at your flat roof and see if you notice anything untoward. If you do, speak to a reputable roofer who can repair your flat roof for you before winter arrives.

Velux windows actually refer to one brand of roof window, which are windows that sit in your roof space and allow light and ventilation into your loft. But how do you install a Velux window? If you’re a competent DIYer, it’s not as difficult as you might think.

You can normally install roof windows entirely from the inside, so you don’t need to get up on your roof or hire costly scaffolding. They come with detailed installation instructions, so as long as you follow them you shouldn’t have much trouble.

Before you start, you’ll need to read up on the Building Regulations and Planning Permission laws. Speak to your local Building Control department if you have any questions.

Firstly, prepare the opening by removing enough tiles or slates from the roof. There’s no need to go out on the roof – access them by cutting away the felt underneath which will give you access to the tiles and battens. Cut away one of the battens from under a tile, then you can slide all the tiles into the roof space. You’ll need to cut away the roof timbers to make the right size opening, then add more timbers to strengthen the ones that are left.

Next, remove the opening sash from the new roof window then fit the frame into the new opening using the brackets provided with the window. Then fit roof flashing between the new window and the roof so you don’t get any leaks. Then lay your tiles back in position around the new Velux window; you’ll probably have to cut some to shape which you can do with an angle grinder. Always cut them on the ground, not in position on the roof.

Lastly, fit the sash back onto the window and you’re done!

If this sounds like too much hard work, plenty of window installers will be able to help you fit a Velux window and will probably be able to provide a much cleaner finish.

Will My Roof Leak With Missing Ridge Tiles?

Your roof is the first line of defence against the elements. Therefore, if you want your home protected at all times, there’s a need to ensure a professional inspection of your home at least once a year. However, there are certain issues that you do not have to wait for a professional to be able to spot by yourself. And an example of this includes a missing ridge tile. This issue is noticeable from the ground level while some tiles may even fall off and notifying you in the process. If you’re currently facing this kind of challenge, you’d probably want to know if the missing ridge tiles can cause your roof to leak. In this article, we aim to answer this question and more. Let’s take a look!

Firstly, there are a number of causes of missing tiles or slates and the most obvious is the weather. When the wind or rain gets very high, it can pull your tiles out of place and even more more, if they weren’t properly installed in the first place. Secondly, there’s also a chance that the nails may wear away. These are the nails that holds your ridge tiles in place, they can rust and wear away, hence leading to missing ridge tiles.

Therefore, the short answer to the question is yes, missing ridge tiles can cause your roof to leak. Even if it doesn’t leave a visible gap in your roof’s covering, it’ll create a break in the roof which weather can easily penetrate. And allowing this to happen makes the other tiles more susceptible to damage which won’t be good for the entire house as well as your pocket. Hence, once you notice a missing ridge tile ensure to have it replaced as soon as possible.

It can be a huge headache, but cleaning of gutters is a task that needs to be done and even more so when it’s a stained white gutter. Nobody want to do it, but everybody has to. If you happen to lack the required confidence to pull this off as it has to do with working at heights, then we’d strongly recommend that you get in touch with a reliable professional who can guarantee the best results for help and also save you some time and money from potential costly errors. In this post, we’re going to show you some of effective way in which you can tackle stained white gutters effectively.

Firstly, you’ll have to take out the ladder with a pair of rubber gloves. Simply position the ladder safely, climb up the roof and start removing the leaves and other debris clogging up the gutters. You can also make use of a garden trowel to remove the very thick debris. Once done, spray the gutter using a garden hose to flush out the dirt as this will make the stains visible. Then prior to cleaning, ensure to cover the plants or landscape underneath with tarp or plastic sheet since the cleaning solution may negatively impact the vegetation.

Start to clean by spraying an all-purpose cleaner on the stains and srub them off using a scrub brush. You can also try a mixture of 1/4 of water with 1 cup of bleach and 1 teaspoon of dish soap. Dip your scrub brush in this solution to scrub off the stains. The bleach mixture is guaranteed to eliminate any mold or mildew that growing on your gutters with ease.