Find a Roofer you can trust near you.

Chimneys are certainly on top of the commonly overlooked features when it comes to cleaning a house. This is quite understandable given the fact that they’re not readily accessible and not in plain sight, hence, home and property owners tend to overlook the relevance of any chimney cleaning effort. But this can be a grave mistake! The importance of having your chimney swept on a regular basis cannot be over emphasized and even more so if it happens to be on a wood burner. Not only can a dirty chimney constitute fire hazard, but when left uncleaned it can also give rise to blockages which can lead to carbon monoxide poisoning. In fact, from 2014 to 2018, one of the top factors contributing to about 25% of home heating fires is due to lack of cleaning, mainly from solid-fueled heating equipment, mostly chimneys. Therefore, sweeping your chimney regularly is a safety precaution and when they happen to be on a wood burner, this exercise becomes a lot more important. With that in mind, the question that arises is just how often is sweeping of a chimney on a would burner needed?

Well, it’s strongly advisable to sweep chimney on a wood burner at least twice a year by a qualified professional depending on the usage. If you happen to own an oil burning fireplace, the same also applies. In other words, this means that regardless of the type of chimney you possess, the cleaning must be done regularly. However, most chimney would only need to be swept once in a year by a qualified professional.

Yes – you can repair a flat roof in the winter. Contractors will still be able to help you repair leaks, and it’s a myth that they will charge more. Most won’t have any additional costs just for coming out in the winter.

You'll have to wait for any snow and ice to melt before you can repair your flat roof. Depending on what type of flat roof you have, some repairs might have to wait until temperatures reach a certain level above freezing – some coating products won’t adhere (stick) in low temperatures, but a roofing professional will be able to advise you on what is best to use in the winter. If you have an EDPM rubber roof, most of the adhesives won’t mix in cold weather, so you might have to wait until temperatures rise to get a proper repair to your flat roof.

The best way to avoid needing to repair your flat roof in the winter is to inspect it at regular intervals. During the summer, even in the UK’s mild weather, the sun’s UV rays can damage and weaken flat roof surfaces, potentially causing cracks and holes. As autumn approaches, take a look at your flat roof and see if you notice anything untoward. If you do, speak to a reputable roofer who can repair your flat roof for you before winter arrives.

How Often Do Flat Roofs Need Replacing?

When a flat roof needs to be replaced is determined by a number of factors which includes the roof’s exposure to the weather, the condition and age of the roofing materials as well as the construction of the roof. However, with proper maintenance and regular inspection, they should be used for nothing less than 50 years. There are some commonly used types of flat roofs which includes Felt flat roof as well as a GRP flat roof.

Felt Flat Roof

The lifespan of a felt flat roof also varies depending on the quality and grade of the felt roof incorporated. This can make the roof last within the range of 2 to 20 years. More often than not, felt flat roofs are usually installed in such a way to keep the costs down which implies the grades of felts that are mostly used are the economical ones implying a very short lifespan.

In the event whereby a premium grade of felt is incorporated in constructing a roof by professional contractors, will be guaranteed by the manufacturer to last between 10 to 20 years.

One of the major causes of a short lifespan in felts is leaks which should be regularly inspected and repaired once identified. If not, the roof will gradually deteriorate and become a lot weaker due to the action of the sun. However, when a felt roof starts to leak, it’s usually a sign that’s approaching the end of its lifespan and a replacement should be taken into account.

GRP Flat Roof

The GRP flat roof or fibreglass flat roof usually comes with a manufacturer’s guarantee of 20 years and is expected to have a lifespan of a minimum of an additional 10 years.

Unlike felt roofs, they’re more resistant to leaks. However, they should also be regularly inspected for leaks which are caused mostly as a result of installation error rather than the GRP roofing approaching the end of its useful life. If the GRP roof repair does not totally resolve the leak, you should start considering a replacement.

Fitting a Velux window into a slate roof is very similar to the way you’d install it in other roof types. All roof windows, whether a Velux-branded one or not, will come with detailed instructions for you to follow if you want to have a go at fitting it yourself. But here are some brief instructions to give you an idea of what’s involved in installing a Velux window into a slate roof:

1. After you’ve removed the Velux window from its packaging, remove the sash (the part that opens) from the frame, according to the manufacturer’s instructions.
2. Next, you need to prepare the opening for the window. You can often cut through the felt, remove one of the battens from under a slate, then slide all the slate tiles into the roof space. You should then make the cut 40-60mm wider than the window, cutting away roof timbers then replacing them with more around the opening to strengthen it.
3. The roof window’s bottom brackets need to be installed on one of the existing battens for the slate roof. One of the slate courses should line up 105mm below the top edge of the batten you use.
4. Then, measure from the top edge of the batten upwards to the height of the window plus 45mm. This is where the top installation batten should be installed, with an overhang of 100mm on each side.
5. Remove the course of slates below the window, trim any excess felt and fold it over the surrounding timber. This helps with waterproofing.
6. Add the insulation collar according to the Velux window manufacturer’s instructions.
7. Place the frame in the opening, adding the brackets according to the instructions. You’ll find that lots of roof windows have pre-drilled holes to make it easy for you.
8. Replace the sash and line up the hinges. Take a look at the opening at the bottom between the sash and the frame – it should be even along the entire width. Remove the sash again to fix the upper brackets according to instructions.
9. Add the underfelt collar for your roof window as instructed by the manufacturer, then replace any slates at the bottom. You might need to cut them to size.
10. Next, add the flashing according to the instructions, along with any parts that are not yet attached, including the hood section and top flashing piece.
11. Replace all the slates around the window, allowing 60-100mm of space between the course of slates above the window and the top of the window to allow for rainwater drainage. Then replace the sash into the frame again.
12. Add the vapour barrier on the inside of the window using the screws provided, then tape it to the existing vapour barrier to prevent moisture from reaching your roof structure.

And that’s it! If you think that sounds a bit complicated, ask a roofer or window installer to fit your roof window into a slate roof for you. You’ll get a better finish and you can be sure that you won’t get any leaks from a botched installation.

You should inspect your roof twice a year, ideally after rain or snow, to see if it’s draining properly. Also in the Spring to check for damage that may of been caused over the winter months that will need to be put right before the next winter. Have an inspection carried out if you are unsure.

Tar and gravel flat roofs are popular because the gravel weighs down the surface of the roof so it doesn’t blow away and it also protects it from sun damage. The tar makes the roof watertight, so you won’t get any leaks. However, sometimes problems occur and you’ll get cracks and leaks. So how do you repair a tar and gravel flat roof?

If you notice leaking coming through your flat roof, try to find the source of the leak. Since water can travel easily, it might not be where you think it is. The first place to check is the flashing, then any parts of the roof with gravel missing. Once you’ve found the crack, sweep away any remaining gravel and clean the area.

Apply a primer to the area and allow it to dry. Then, apply a tar and gravel roof patch that you can get from most DIY shops. Patch 2-3 inches around the damaged area, creating layers, and ensuring that there aren’t any air bubbles or gaps. Then you should cover the entire patch with gravel.

Before you try to repair a tar and gravel flat roof yourself, consider how much of the roof needs repairing. Professionals often say that if cracks and faults make up 25% or more of the roof, then you should look to replace it. It might be tempting to try and replace your tar and gravel roof yourself, but it’s best left to the specialists. They will ensure that your new roof is watertight and strong enough to withstand sun damage and storms.

Leaves, twigs and moss all have one thing in common which often annoys home and property owners - they are the three main materials that negatively impacts the proper functioning of a roof guttering system. The major cause of water drainage problems for most homes and buildings are these organic materials. Wondering how some leaves and few twigs can cause such a big problem? Over time there’ll be a gradual build up of the natural debris in your gutter system which starts to rot and turn  to a thick and muddy goo which obstructs the flow of water in your drainage. As a result, there’s the need to make sure that your gutters are thoroughly cleaned at least twice annually in order to prevent bigger issues that can be caused by the blockage of a drainage system.

So if you’re considering getting your gutters cleaned by a professional, you’d probably be interested in know just how it’s going to cost. Well, there’s not straightforward and simple answer to this question as there are a number of factors that contributes to the final cleaning cost of your gutters.

In general, in the UK, the average cost for cleaning of gutter is usually around £18 to about £25 per hour. However, you can also be quoted a day rate which is usually ranging between £150 to £200 per day.

The factors that can affect gutter cleaning price includes the type of your property (such as a terraced, end of terraced, detached and semi detached homes) which possesses a varying gutter cleaning price largely due to their size differences, the height of the building ( if you require the service for a property located on the second floor of a building, this would be a bit higher than if it were to be on the ground floor) as well as additional requests.

Clean of your conservatory gutter is probably not one of the most enjoyable chores you’d like to take on around the house. Not only is it messy and tedious, but it’s also time consuming and smelly. It’s a job every home and property owner would rather avoid, but unfortunately everyone has to do it. It’s a necessity due to the fact that neglect gutters holds and harbours mould, moss as well as plant debris. It would have been better if this is only disgusting, but the actual truth is that should be the least of your worries as this gradual build up of organic material in your conservatory gutters can minimize their drainage abilities, leading to leakages and spills that can damage your conservatory.

Cleaning of your conservatory gutter is a task that can be done regardless of your level of experience. However, it’s advisable to call in a professional for help especially if you lack the confidence required to pull it off.

• Use a ladder for a closer look. Cleaning your gutters from the ground by poking it with a hooked tool might seem the best way out, but in truth you risk damaging the gutters or brackets and marking the conservatory panes when you don’t see what you’re doing.
• Invest in specialist tools. For expert DIYers, taking off your downpipes from the wall to clean might be a pretty easy task. However, for most people it can be extremely frustrating. As a result, there’s the need to get hold of some flexible gutter brushes. With a bendable stem and stiff bristles, these are able to hook and dislodge dirt and leaves inside your downpipes with relative ease.