Find a Roofer you can trust in Newport-on-tay.

Tar and gravel flat roofs are popular because the gravel weighs down the surface of the roof so it doesn’t blow away and it also protects it from sun damage. The tar makes the roof watertight, so you won’t get any leaks. However, sometimes problems occur and you’ll get cracks and leaks. So how do you repair a tar and gravel flat roof?

If you notice leaking coming through your flat roof, try to find the source of the leak. Since water can travel easily, it might not be where you think it is. The first place to check is the flashing, then any parts of the roof with gravel missing. Once you’ve found the crack, sweep away any remaining gravel and clean the area.

Apply a primer to the area and allow it to dry. Then, apply a tar and gravel roof patch that you can get from most DIY shops. Patch 2-3 inches around the damaged area, creating layers, and ensuring that there aren’t any air bubbles or gaps. Then you should cover the entire patch with gravel.

Before you try to repair a tar and gravel flat roof yourself, consider how much of the roof needs repairing. Professionals often say that if cracks and faults make up 25% or more of the roof, then you should look to replace it. It might be tempting to try and replace your tar and gravel roof yourself, but it’s best left to the specialists. They will ensure that your new roof is watertight and strong enough to withstand sun damage and storms.

Ponding is where you see pools of water appearing on your flat roof. Unless your roof is leaking or showing other signs of damage, you don’t need to replace it. When you do have your flat roof replaced, tell the contractor so they can find out the cause of the ponding.

Chimneys are certainly on top of the commonly overlooked features when it comes to cleaning a house. This is quite understandable given the fact that they’re not readily accessible and not in plain sight, hence, home and property owners tend to overlook the relevance of any chimney cleaning effort. But this can be a grave mistake! The importance of having your chimney swept on a regular basis cannot be over emphasized and even more so if it happens to be on a wood burner. Not only can a dirty chimney constitute fire hazard, but when left uncleaned it can also give rise to blockages which can lead to carbon monoxide poisoning. In fact, from 2014 to 2018, one of the top factors contributing to about 25% of home heating fires is due to lack of cleaning, mainly from solid-fueled heating equipment, mostly chimneys. Therefore, sweeping your chimney regularly is a safety precaution and when they happen to be on a wood burner, this exercise becomes a lot more important. With that in mind, the question that arises is just how often is sweeping of a chimney on a would burner needed?

Well, it’s strongly advisable to sweep chimney on a wood burner at least twice a year by a qualified professional depending on the usage. If you happen to own an oil burning fireplace, the same also applies. In other words, this means that regardless of the type of chimney you possess, the cleaning must be done regularly. However, most chimney would only need to be swept once in a year by a qualified professional.

How you install commercial rubber roofing is similar to fitting it on a residential property, except that the area that’s covered is likely to be bigger. With commercial properties, you should always leave any maintenance and repair works to the professionals – whether you own or lease the property, you could invalidate any insurance if you try to install rubber roofing yourself. We’ll outline the steps roofers will take when installing rubber roofing on a commercial property.

Firstly, the installers will remove any existing coverings and clean and dry the surface thoroughly. This is vital in ensuring that the rubber will stick. They will then unwrap the EDPM rubber membrane and leave it to rest until it’s fully expanded. On a warm day this may take around half an hour.

Next, the roofers will work with half a sheet of rubber at a time and adhere it to the roof surface. They may use a water-based adhesive which they will spread onto the roof in sections, then roll the membrane onto the surface before moving onto the next section. If they’re using a bonded adhesive, they will apply it to both the roof and the rubber and leave it to dry until it’s tacky before extending the membrane.

Once the EDPM rubber is rolled out, the installers will brush the surface with a large broom to get rid of bubbles and provide a stronger bond. Then they will work of the edges, applying adhesive to roof and walls edges, sealing corners and creating watertight seals. They’ll also tidy up any excess membrane and seal all the trims.

As long as it’s installed correctly, your commercial rubber roofing should last you decades without any repairs needed. It’s always best to inspect your roof regularly to spot any damage before it becomes a bigger problem.

Roof tiles should be replaced as soon as possible to ensure that your roof stays waterproof. Use crawl boards when replacing them to avoid damaging other tiles, if not ask a qualified roofer to carry out the work, particularly if the tiles are higher up.

A roof serves as something which is so much more than just a top of a building. A roof delivers guard from the elements and precipitation, it also helps drain water from a structure, and helps to provide insulation to the structure allowing it to keep the interior of a building cool or warm, according to season.

There are several steps to building a roof

Mount the trusses.

This step requires the building’s wall frames to be completely level, square and plumb. If you are building the roof onto a building that is still a frame you must use ladders or scaffolding. Hoist the trusses onto the roof.

Install temporary braces.

You will need to install temporary braces that the trusses can rest on until the sheathing and permanent bracing are installed, this has to be done before you install the trusses. At the centre of the back wall, nail the bottom half of one two-by-six board that's 16 feet long to the top of the outside wall, making sure you fasten it to a stud.

Install the end trusses.

Install the two end trusses at the front and back of the building, making sure you affix them to the temporary bracing. The batten you take will have to be a bit longer than the distance will separate the trusses.

Install the standard trusses.

According to the instructions provided by the manufacturer, you will first need to install the first standard truss. You will also need to nail it to the batten from the first truss.

Sheath the roof.

Once your trusses permanently braced, you can begin with the sheathing of the roof. Starting from the bottom corner and moving across the bottom, the sheathing is installed lengthwise.

Install the roof cover.

Like the sheathing and underlayment procedures, the roof cover is installed lengthwise from the bottom up. The shingles should be staggered, and they should also overlap at the same time. You will need to work up to the ridge and use a ridge cap shingles to finish the ridge.

If your existing roof is still in good condition but the membrane is getting old, it’s often not worth exposing the structure to the weather whilst the contractor strips off the old membranes. The contractor will leave them in place to act as a base layer for a new roofing system. As long as there are no other problems with your roof, then overlaying is a good way to replace your flat roof.If you have any more questions about flat roofing that aren’t listed here, fill out our form to ask a contractor.

The roof is a particularly important part of the home, providing weather and water protection. Therefore, it’s important to regularly check your guttering system and clean out any debris that could cause blockages.Advice given is to consider having a mesh gutter guard to prevent the build-up of leaves and other debris, especially if you want to harvest rainwater.