Find a Roofer you can trust in Sandbach.

Velux windows, or roof windows, are very easy to clean. Regular cleaning helps to keep them looking bright and shiny for years to come. So how should you clean Velux windows?

If you want to clean the air filter, you can remove it and wash it with your normal household cleaners. Velux windows have a cleaning position, so rotate and secure it into this position then remove the filter. You should be able to buy new filters from the manufacturer of your roof window.

To clean the outer pane, there’s no need to lean out of the window and risk falling out. Simply rotate the sash (the opening part) 180 degrees and secure it into position. Then you can clean the pane with a soft, lint-free cloth, sponge or squeegee and clean water. If you live in a hard water area, add some detergent to the water and wipe the window dry when you’re finished. You can also use normal non-abrasive household cleaners.

It’s recommended that you clean the flashing around your roof window at least once a year. You can use a brush to do this. This will allow rainwater to flow freely and stop any leaves from collecting.

If you’re in any doubt about using certain cleaners on your Velux windows, get in touch with the manufacturer who should be able to help. You can also do a patch test on an inconspicuous area if you’re unsure.

Blisters are most common on membrane roofing systems. Lots of contractors will tell you that if there are no signs of further damage, there might not be any need to repair flat roof blisters. They form when pockets of air or water get trapped between layers of the roof’s membrane or between the membrane and the frame. When the sun is out and it heats the pockets expand and stretch the membrane. If you do want to repair your flat roof blisters, there are a few ways to go about it.

If you have a membrane flat roof, cut away the membrane until you reach a place where the membrane is still stuck tightly to the roof. Reapply as many new membrane layers as you cut away over the blistered area. You might even need to do more. To make sure your patch remains watertight, you’ll need to leave at least 6 inches around the edges of the blister.

If you’ve got a felt roof, you can cut an X shape through the blister. Peel back the triangles that you’ve made and let the timber frame dry for a while (so don’t do this when rain is forecast!). Then, coat the area with lots of bitumen adhesive and leave it to dry until it feels tacky. Then press down the triangles of felt firmly into the adhesive.

After that, you’ll need to add more bitumen adhesive to the cuts you made. If you’ve got any spare roofing felt, cut a square that’s about 100mm bigger than the cuts then lay this over the adhesive. If you’ve not got any felt, it’s cheaper to use a self-adhesive flashing strip. Once you’ve laid the strip or patch over, seal the edges with more bitumen adhesive.

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

How to repair a flat roof depends on the type of flat roof you have. We’ll talk about how to repair felt, asphalt, fibreglass and EDPM flat roofs yourself. But ultimately if you want the best finish, it’s best to ask a professional to repair your flat roof for you. Repairing a flat roof Whether you’ve got an old pour-and-roll type felt roof or a newer torch-on felt flat roof, you can get cracks, lifting around joints, leaks or dips. As a temporary measure, you can buy a special paint that you paint over cracks. For a more permanent repair, you can add a patch of torched-on felt or add a layer on top. Asphalt flat roof repair As your asphalt flat roof gets older, you may notice blisters, cracks or shrinkage and sagging around flashings. Again, you can use a paint on fix from a tin as a temporary repair, or add heat-applied flashing tape around flashing. For a more permanent fix you can use a liquid system, but many are only available to the trade market. You can also add a patch of torched-on roofing felt over a crack. How to repair a fibreglass (GRP) flat roof Fibreglass flat roofs are usually excellent, but problems can involve leaking flashing and cracks near upstands, trims or board joints. You can add acrylic sealant to cracks or holes for a good DIY repair, but a flashing problem is more difficult to fix. You’ll need to clean and sand the affected area of flashing, then laminate a 600g chopped strand mat into place, cure it and add a topcoat colour to match the roof. That sounds like a job better left to a specialist. EDPM rubber flat roof repair Rubber roofs often suffer from shrinkage when mechanical fixings haven’t been used near upstands, flashing leaks or holes or cuts. If you’ve got a small tear that you want to repair, you can add some lap sealant to the area – but use it sparingly. For a more permanent repair to flashing, buy some self-adhesive flashing that will mould into shape easily. Clean the area you want to repair, add EDPM primer, then stick the patch of flashing on from the centre outwards with a hard roller. You can add lap sealant around the edges if you want more protection from water.

It can be easy to repair a felt flat roof depending on the problem. If you’ve got an old-style pour-and-roll felt flat roof, you might be starting to run into problems, but even if you have a newer torch-on felt roof, issues can occur. You might find cracks, lifting, leaking flashings or dips and hollows in the felt. Luckily, there are some easy fixes – but the best thing to do to prolong the life of your felt flat roof is to get a professional to look at it.

If your felt flat roof only needs a small repair, you might be able to get away with using a paint-on fix from a tin that you just brush on. However, if you want a more permanent fix, you’ll need a few more tools and supplies.

You can use a patch of torched-on roofing felt over the crack or leak, but if your flat roof is very damaged or wet it might not take it. You can also buy liquid systems for felt roofs, but again, there is a possibility that your roof might not take it. Also most of the high-quality liquid systems are only available for trade customers, so you might be better off asking a roofing pro to do it for you.

How much a flat roof costs to repair depends on a few factors. Is your flat roof on a garage or an extension? What is the flat roof made from? It’s always best to get a few quotes to compare prices, but we’ll give you a rough idea here. If your flat roof was installed in the 1990s or earlier, it’s likely that you’ll see some leaks or damage soon. Felt flat roofs used to be installed completely flat, which meant that water couldn’t run off. That means that water pools and can create moss and damp. Sun exposure can also damage the felt, causing damage and eventually holes that lead to leaks. If you’re lucky enough to have got away with just needing a flat roof repair, this should set you back an average of £100 per square metre. If your roof is sagging due to the weight of it putting pressure on the timber frame, you might need additional joists – which could cost anywhere between £1,000 and £2,000, depending on how many you need. But if the problem is due to the internal part of the roof system becoming waterlogged, you could be looking at over £5,000. If your roof is severely leaking or the timber joists are rotting, it might be more cost effective to replace your flat roof. If you keep forking out for repairs, it will eventually be cheaper just to replace the whole thing, which could cost around £2,000.

Ponding is where you see pools of water appearing on your flat roof. Unless your roof is leaking or showing other signs of damage, you don’t need to replace it. When you do have your flat roof replaced, tell the contractor so they can find out the cause of the ponding.

If you’ve never had Velux windows before, you might be wondering how to open them. If you’ve got very high ceilings and your roof windows are set high up in the pitch of the roof, you might not even be able to reach them. So how do you open them in this case?

When Velux windows are installed so high that they’re out of reach, the installers will often recommend that they install an electric switch for you to open and close your windows. They often come with a rain sensor, so you don’t need to rush up to the top of the house if there’s a sudden downpour – they will close automatically. You can also choose to have a remote so you can open and close your roof windows wherever you are in the room.

If you don’t have an electric switch, but you still can’t reach to open and close your Velux windows, you should be supplied with a telescopic pole when they’re installed. If you weren’t or you’ve moved into a home with roof windows and there isn’t one, you can buy them online. They have a hook on the end and can be extended to the correct length so you can hook it over the handle of the window and pull or push to open it.

If you’ve got a top-hung Velux window that can also be opened in a centre-pivot position, it’s easy to switch between the two. Simply ensure the window is completely closed before you start, then open the handle up – but don’t push it out. Then pull the vent bar down until the sash is rotated 180 degrees. Then secure the position by sliding the barrel bolts into the holes at either side of the bottom of the frame. Easy!