Find a Renewable Energy Specialist you can trust in West Sussex.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

Most people want to connect solar panels to a battery when they’re not at home all day to use the electricity they generate, or generate more than they consume over a day. Solar batteries are a great way to maximise the savings on your energy bills since you can use every unit of electricity you generate.

If you want to connect your solar panels to a battery, the best – and safest – way is to ask an MCS-registered company to do it for you. They’ve had lots of training and hold qualifications in handling electricity and installing solar batteries, so they will be able to recommend the best battery for your solar panels and for the among of electricity you use. Some of the brands they might recommend include Tesla, SolarEdge and SolaX, but there are many more to choose from. If you want to send electricity to the grid from your battery to receive Smart Export Guarantee (SEG) payments, it’s also worth leaving installation up to a registered installer. This is because you might not be eligible for payments if your battery wasn’t installed by an MCS-registered company.

However, if you do want to have a go at connecting your solar panels to a battery, it’s worth finding out whether your system is ‘storage ready’. Most relatively new systems will be, since batteries are becoming more commonplace. If your solar panels are storage ready, they will have an inverter that can easily have a battery added to it. If this is the case, then you should be able to buy the solar battery you want and follow the manufacturer's instructions to install it.

But it’s worth remembering that electricity is extremely dangerous when handled improperly. If you don’t get the solar battery connected properly and something goes wrong, it could cause a fire or you could electrocute yourself. If a fire breaks out due to your battery, it’s unlikely that your home insurance company would pay out since you connected the battery yourself. That’s why it’s always worth speaking to a registered installer to install a solar battery storage system for you.

Unlike the photovoltaic (PV) power which works to turn a part of the electromagnetic radiation of the sun directly to electrons and electricity, a solar thermal can simply be referred to as the absorption of the sun’s heat for human use. As a result, the solar thermal has a wider range of uses than the PV does in several ways. This is due to the fact that the sun’s heat can be absorbed and transported via a medium and the stored energy incorporated for several great purposes such as to heat water, to heat and cool a home or living space, to prepare a meal as well as to generate electricity. All these functions are useful for both residential and commercial spaces.

There are generally three different ranges of solar thermal energy that are being used which includes the low temperature ( for heating, cooling as well as ventilation), the mid temperature ( used for preparing meals, heating hot water and the likes) as well as the high temperature ( used for generating electricity). To focus more on generating electricity, there are a wide array of ways through which the sun’s heat can be directed at creating electricity via a heat exchanger which operates to super heat water or inert gas to power an electricity- generating plant or to produce electricity via a Stirling engine.

In order to increase their output or make them more efficient, evacuated glass tubes are used to encircle the tubes which in turn helps them to collect more heat energy while also protecting them from re-radiating the heat energy absorbed. The trough are normal positioned north to south as well as to keep tabs on the travels of the sun throughout the day.

If you look after your air source heat pump, it can last for over 20 years. Make sure you check it every year and get a registered or qualified installer to check it every 3-5 years to prolong its life. If in doubt, check the manufacturer’s maintenance instructions.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.

If you’re considering getting a solar thermal system, one of the first things that comes to mind is the possibility of the system functioning properly during the cold months. The short and simple answer to this question is yes, a solar thermal system works in the winter. However, the downside here is that it’ll be a lot less efficient when compared to how it operates during the warmer months or summer. As a result of this fact, you’ll likely need to rely more on your boiler, immersion heater or any other backup heating system during this period as your solar thermal system will fail to contribute as much as it does during the warmer months. So what exactly is the reason why solar thermal is less effective and less efficient in the winter period? Let’s have a look!

As you know, solar thermal system banks on the sun’s energy to heat the water for your home’s use. During the cold months or winter, the sunlight becomes a lot less available when compared to the warmer months, as a result, there’s less sunlight that’s available to be used for its solar energy. And even more so at the periods when the days are shorter or skies are clearly overcast.

Also having a great impact on a solar thermal system’s output is heavy snow. Flat plate collectors normally have the capacity to cope better during snowy conditions as the light that’s able to travel through the snow will heat up the absorber plate - thereby making the snow slide off more quickly. However, the case is contrary with evacuated tube collectors which possesses a form of vacuum insulation that’s crafted to minimize the loss of heat, meaning they can’t generate heat to melt and cause the snow to slide off in a similar way.

Air source heat pumps are a type of heating system that you can use to warm the air in your property. They’re a semi-renewable energy generator as, although they use electricity, they extract and use renewable heat from the air.

There are two main types of air source heat pump – air-to-water, and air-to-air. Air-to-water heat pumps are the most popular, and are best used to heat water that supplies underfloor heating systems or large radiators. Air-to-air pumps heat air, which is then dispersed round your property using fans.

Do you want a low carbon way of heating your home? Then, getting an air source heat pump is the way to go! What they do is pretty simple - they absorb the potential thermal energy present in the outside air and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. In other words, it functions by extracting heat from a cooler place and then uses it to raise the temperature inside a home or property. Being very similar to air conditioning units, the amount of heat they’re going to produce for your home or property will be dependent on the size you install. Therefore, the bigger the heat pump, the more the heat that’ll be generated.

Air source heat pumps have two main types which includes air to air and air to water. Air-to-water heat pumps works by absorbing heat from the outside air, then relays it directly into your home or property through the help of fans. In order to move the heat around your home, you’ll need a warm air circulation system. This type of air source heat pump are not eligible for the government’s Renewable Heat Incentive Payment as they can’t generate hot water. What’s more? They can function in reverse during the hot summer months.

Air-to-water heat pumps, on the other hand, operates by extracting heat from the outside air and transmitting it into the wet central heating system. Due to the fact that they’re able to generate heat that’s cooler than the one generated by a conventional gas or oil boiler, they happen to be a better fit for larger radiators or water underfloor heating.

You shouldn’t need to maintain your solar panels much at all as long as there’s nothing piled up on top of the panels that could block out the sun. They are installed at an angle, so when it rains the water runs off them and gives them a clean. However, if this doesn’t quite cut it, you can spray them with a hose a few times a year.