Find a Renewable Energy Specialist you can trust in Belford.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

There are two main types of air source heat pump: air-to-water and air-to-air. They work in different ways and have different advantages and disadvantages. Make sure you do your research so you know which one is best for you. Alternatively a registered installer will be able to determine the best type for your property.

Unlike the photovoltaic (PV) power which works to turn a part of the electromagnetic radiation of the sun directly to electrons and electricity, a solar thermal can simply be referred to as the absorption of the sun’s heat for human use. As a result, the solar thermal has a wider range of uses than the PV does in several ways. This is due to the fact that the sun’s heat can be absorbed and transported via a medium and the stored energy incorporated for several great purposes such as to heat water, to heat and cool a home or living space, to prepare a meal as well as to generate electricity. All these functions are useful for both residential and commercial spaces.

There are generally three different ranges of solar thermal energy that are being used which includes the low temperature ( for heating, cooling as well as ventilation), the mid temperature ( used for preparing meals, heating hot water and the likes) as well as the high temperature ( used for generating electricity). To focus more on generating electricity, there are a wide array of ways through which the sun’s heat can be directed at creating electricity via a heat exchanger which operates to super heat water or inert gas to power an electricity- generating plant or to produce electricity via a Stirling engine.

In order to increase their output or make them more efficient, evacuated glass tubes are used to encircle the tubes which in turn helps them to collect more heat energy while also protecting them from re-radiating the heat energy absorbed. The trough are normal positioned north to south as well as to keep tabs on the travels of the sun throughout the day.

Solar thermal panels work by capturing heat directly from the sun and using it to heat water. This hot water is then passed through a coil to heat the water for your central heating system. Solar thermal systems are compatible with many existing conventional boilers with hot water tanks, and can be set up to feed in to your existing heating system.

You shouldn’t need to maintain your solar panels much at all as long as there’s nothing piled up on top of the panels that could block out the sun. They are installed at an angle, so when it rains the water runs off them and gives them a clean. However, if this doesn’t quite cut it, you can spray them with a hose a few times a year.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

Air source heat pumps work by taking heat from the air and using it to heat your home. They absorb heat from the air into a fluid, which then goes to a compressor where it gets hotter. This heat is then used to warm up water or air, which is distributed around your home.

First and foremost, you should know that heat pump is simply a device whose primary function is the transmission of thermal energy from one spot to the other. A good example can be found in the refrigerators whereby the evaporation as well as cooling of a liquid is incorporated to lower the storage compartment’s temperature. In recent times, this whole technology is utilized to draw the potential thermal energy present in the air outside and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. This is exactly what an air source heat pump does as it absorbs heat from the air and convert it into a higher temperature using a compressor. How the air source heat pump works is really simple, it’s just like a refrigerator but in reverse. Let’s take a look!

• The air source heat pump extracts heat present in the outside air into a liquid refrigerant at a reduced temperature.
• The pump then compresses the liquid to increase its temperature with the help of electricity. Once done, it then compresses it back to liquid so as to free the heat stored.
• The heat released is then directed to the radiators or under floor heating, while the ones left would be stored in the hot water cylinder.
• The hot water that’s stored can be used for showers, baths as well as taps.

Overall, the air source heat pump is an efficient way to make your home warm. It makes use of electricity to function, but it should consume lower electrical energy than the heat it generates.

If you’re thinking about installing a solar thermal system in your house, it’s always important to put into consideration numerous factors before you proceed. While some solar thermal systems are suitable for use at home, there are also some that are suitable for businesses or organizations which normally requires a big amount of hot water like hotels, restaurants, schools, hospitals and many more. You’ll also find some types available in the market that are suitable for communities to satisfy communal hot water demands.

It should, however, be noted that solar thermal systems do not have the capacity to produce all the hot water demand of a house. In the UK, an average household will need an annual water heating of between 3000kWh to 5000kWh. Whereas, a solar thermal system is only able to meet about 40 percent to 60 percent of this demand.

With that in mind, it’s also worth noting that during the summer months when the solar radiation is at its peak and hot water demand is relatively lower when compared to other seasons, a solar thermal system may be able to provide all of your household’s hot water needs. This implies that during this period you may not find the need to operate your boiler at all. However, during winter or colder months, when you have a higher hot water demands in contrary to a lower solar radiation, a solar thermal system will only be able to take care of about 20 percent of your household’s hot water needs. And that ultimately implies that during this period, you’ll need to rely more on a alternative or backup source of heat like gas, coal, electricity, oil or LPG.