Find a Renewable Energy Specialist you can trust in Attleborough.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

There are a few factors that will determine whether it’s worth getting a solar battery. They involve how much electricity you use, how often you’re at home and whether you receive any export payments.

To work out whether it’s worth getting a solar battery, you need to work out how much of the electricity you generate you’re using already. If you’re able to run all your appliances during the day while your solar panels generate electricity, then it sounds like you’re already using your electricity well. It might not be worth you getting a solar battery in this case.

However, if you’re not at home for a lot of the day, then you’ll be missing out on the electricity your panels are generating while the sun’s shining. If you install a solar battery system, you can store the electricity that your panels generate in the battery and use it when you get home. This will help you cut your electricity bills even further.

You’ll also need to consider whether you’re getting paid to export your electricity. If you’re on the Feed-in Tariff scheme (FITs) or receive payments from the Smart Export Guarantee (SEG), you’ll get paid for every unit of electricity you export to the National Grid. Before you decide whether it’s worth getting a solar battery, you’ll need to weigh up whether you’d be better off carrying on exporting your unused electricity rather than storing it to use yourself. If you’re unsure, visit the Energy Saving Trust’s website or speak to an MCS-registered installer who will be able to help you work out which is more cost-effective.

When you’re about to transform from the standard electricity to solar energy, what determines your solar system’s size is the amount of solar that’s required. The amount of solar that you’ll need, on the other hand, requires considering the end goal, be it to increase money savings, reduce environmental contamination, maximize Returns On Investment ( ROI), or just to copy what the neighbour’s done.

In order the determine the number of solar panels that is needed, the first step would be to calculate the number of kWhs that’s currently being used. A kWh is what’s used to determine the amount of energy that has been incorporated over time which the utility uses to bill you. What’s strongly recommended to create a suitable range is a 6 to 12 months average of your household electricity bill. Other factors that can play a key role in the determination of the number of solar panel needed include the following:

✓ Sunlight exposure hours. In order to know just how much energy your solar panels will generate, there’s a need to know the number of direct sunlight hours you should expect on a daily basis. For example if you stay in a region that’s usually very sunny, then it’ll be reasonable to expect more energy production per panel than regions that are usually cloudy.

✓ Angle and size of the roof. Roofs with a lot of workable space may require to let go of some efficiency opting for larger and cost effective panels to achieve the targeted energy. However not all homeowners have sufficient roof space or shade coverage for the solar panel they actually want. Also, the degree at which the roof slants will also determine if the sunlight is hitting the panels well enough and the amount of energy that can be generated thereof.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

Air source heat pumps work by taking heat from the air and using it to heat your home. They absorb heat from the air into a fluid, which then goes to a compressor where it gets hotter. This heat is then used to warm up water or air, which is distributed around your home.

First and foremost, you should know that heat pump is simply a device whose primary function is the transmission of thermal energy from one spot to the other. A good example can be found in the refrigerators whereby the evaporation as well as cooling of a liquid is incorporated to lower the storage compartment’s temperature. In recent times, this whole technology is utilized to draw the potential thermal energy present in the air outside and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. This is exactly what an air source heat pump does as it absorbs heat from the air and convert it into a higher temperature using a compressor. How the air source heat pump works is really simple, it’s just like a refrigerator but in reverse. Let’s take a look!

• The air source heat pump extracts heat present in the outside air into a liquid refrigerant at a reduced temperature.
• The pump then compresses the liquid to increase its temperature with the help of electricity. Once done, it then compresses it back to liquid so as to free the heat stored.
• The heat released is then directed to the radiators or under floor heating, while the ones left would be stored in the hot water cylinder.
• The hot water that’s stored can be used for showers, baths as well as taps.

Overall, the air source heat pump is an efficient way to make your home warm. It makes use of electricity to function, but it should consume lower electrical energy than the heat it generates.