Find a Renewable Energy Specialist you can trust in Gillingham.

Solar thermal panels work by capturing heat directly from the sun and using it to heat water. This hot water is then passed through a coil to heat the water for your central heating system. Solar thermal systems are compatible with many existing conventional boilers with hot water tanks, and can be set up to feed in to your existing heating system.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

It may be hard to believe with the summers we have in the UK, but there is more than enough sunlight to power solar panels. Solar PV (photovoltaic) panels operate in daylight, rather than needing direct rays from the sun so they’ll work throughout the year.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

Air source heat pumps work by absorbing heat from the outside air and transferring it inside to heat up your property.

An air source heat pump has an outdoor unit containing a refrigerant. This absorbs heat from the air and passes into a compressor, where the temperature is increased. The heat then transfers either into water, which feeds into your wet heating system, or into air, which is dispersed around your property.

Air source heat pumps need electricity to run, but this is to power the compressor rather than directly generate heat.

Air source heat pumps are a type of heating system that you can use to warm the air in your property. They’re a semi-renewable energy generator as, although they use electricity, they extract and use renewable heat from the air.

There are two main types of air source heat pump – air-to-water, and air-to-air. Air-to-water heat pumps are the most popular, and are best used to heat water that supplies underfloor heating systems or large radiators. Air-to-air pumps heat air, which is then dispersed round your property using fans.

Do you want a low carbon way of heating your home? Then, getting an air source heat pump is the way to go! What they do is pretty simple - they absorb the potential thermal energy present in the outside air and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. In other words, it functions by extracting heat from a cooler place and then uses it to raise the temperature inside a home or property. Being very similar to air conditioning units, the amount of heat they’re going to produce for your home or property will be dependent on the size you install. Therefore, the bigger the heat pump, the more the heat that’ll be generated.

Air source heat pumps have two main types which includes air to air and air to water. Air-to-water heat pumps works by absorbing heat from the outside air, then relays it directly into your home or property through the help of fans. In order to move the heat around your home, you’ll need a warm air circulation system. This type of air source heat pump are not eligible for the government’s Renewable Heat Incentive Payment as they can’t generate hot water. What’s more? They can function in reverse during the hot summer months.

Air-to-water heat pumps, on the other hand, operates by extracting heat from the outside air and transmitting it into the wet central heating system. Due to the fact that they’re able to generate heat that’s cooler than the one generated by a conventional gas or oil boiler, they happen to be a better fit for larger radiators or water underfloor heating.