Find a Renewable Energy Specialist you can trust in Welwyn.

If you look after your air source heat pump, it can last for over 20 years. Make sure you check it every year and get a registered or qualified installer to check it every 3-5 years to prolong its life. If in doubt, check the manufacturer’s maintenance instructions.

If you’re thinking about the possibility of installing a ground source heat pump in your home, then it’s normal to consider how efficient they’re in heating up a house before going ahead to make a purchase decision. In this article, we are going to address this question to help you make an informed purchase decision.

We know you’d prefer a single, accurate answer to this question, but the fact is, there are several influencing factors that can play a key role in the efficiency of a ground source heat pump installation. These factors include whether or not the property is well insulated, the fitting of a well designed system and the quality of its installation, the heat source that’s being used as well as the heating distribution system and its size ( under floor heating or radiators ).

The Coefficient of Performance ( CoP) measurement is used to imply the efficiency of a heat pump. This is basically the ratio between the amount of heat energy generated by the ground source heat pump and the amount of electrical energy or fuel it consumes. Therefore, the Seasonal Coefficient of Performance ( SCoP) is usually taken as a realistic measurement to cover throughout the year as its based on CoP at varying conditions as well as a standardized climate.

You must, however, note that there is no established Coefficient of Performance for ground source heat pumps as they can be influenced by a lot of factors as well as testing conditions. When they’re properly fitted, ground source heat pumps can achieve a quite high Coefficient of Performance.

Generally, a ground source heat pump can generate about 3 to 4 kilowatts (kW) of heat for every 1 kilowatt to electricity or fuel it consumes. It’s able to achieve a higher efficiency when compared to its counterparts by using the freely available heat energy from the ground.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

It may be hard to believe with the summers we have in the UK, but there is more than enough sunlight to power solar panels. Solar PV (photovoltaic) panels operate in daylight, rather than needing direct rays from the sun so they’ll work throughout the year.

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

First and foremost let’s look at the meaning of a ground source heat pump. A ground source heat pump is simply a renewable heating system which happens to absorb the low temperature solar energy stored in the ground or in water with the help of a pipework that’s submerged and converts this energy into a higher temperature through compression. A ground source heating pump is capable of supplying the entire heating and hot water needs of a building throughout a whole year regardless of the season. So how exactly does a ground source heat pump work? Let’s have a look!

In principle, a ground source heating pump makes use of a refrigeration system but in a reverse form as it extracts low temperature heat from one point or location which is the source and transfer a higher temperature heat to another point or location - the sink. The pumps are powered by electricity and the operational principle can also be incorporated at generating both heating and cooling energy.

Knowing fully well heat naturally flows from warmer to cooler places, the ground source heat pump takes advantage of this physics by distributing a cold fluid via ground array pipework either in the ground or in water. It’s able to extract low grade energy from external sources of heat which includes soil, rock, lakes as well as streams.

Once the absorbed energy has been released to the heat pump from the ground or water, the fluid proceeds with its circuit back to the pipework to start its cycle all over again. Some of the benefits of the ground source heat pumps includes low carbon emission and improved air quality, efficient and affordable heating, the use of free heat from the ground and lots more.

Biomass boilers will work with existing central heating systems, presuming this is not decades old, whether they use radiators or under floor heating. A surveyor will check the existing system you have in place before quoting for or recommending a biomass boiler to you.