Find a Renewable Energy Specialist you can trust in Lyndhurst.

If you look after your air source heat pump, it can last for over 20 years. Make sure you check it every year and get a registered or qualified installer to check it every 3-5 years to prolong its life. If in doubt, check the manufacturer’s maintenance instructions.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

The bigger the ground source heat pump, the better right? Wrong! And you’ll definitely be sorry to make such a huge mistake. When planning to install a heat pump, determining the size of the ground source heat pump is not as direct and straightforward as many homeowners would think. Here, you’ve got only a small margin for error. When the pump is too small, the heat pump will make use of the backup heater too often and in the event whereby the heat pump is too big, it’s going to short cycle. Both situations are preferably avoided as they’ll both leave you with an expensive and inefficient system.

To get the accurate size of a heat pump, there’s usually the need to hire the services of an expert and licensed heat pump installer who possesses a top notch design calculation software. In reality, the majority of inefficient systems are caused by a lack or poor understanding of the suitable design software.

There are many factors that can influence the calculation of a home’s heat pumps size. These includes

✓ Radiators and underfloor heating sizes

✓ Insulation, property fabric as well as heat loss

✓ The number of rooms in the property

✓ The types of rooms and their uses.

✓ The desired indoor temperature for varying rooms

✓ Seasonal temperature fluctuations.

Generally, a bigger house will require a bigger ground source heat pump. With an eye on the age of the property, heat loss as well as the types of the rooms, a house of about 100 square metre can require up to 4kW ground source heat pump. And for a house that’s about 200 square metre, the ground source heat pump also doubles to 8kW.

How Much To Install Solar Panels And Battery?

Are you thinking about installing solar panels and battery in your home and wondering how much the installation is going to cost? Well, you’re not alone. This is one of the most commonly asked questions in the solar world, but unfortunately a precise answer can not be provided. This is mainly due to the fact that solar panel systems come in varying sizes which is the main influencing factor that determines how much electricity that can be generated. In other words, the larger the system, the more the electricity that’ll be produced to your home’s benefit.

Generally, for a solar system size of 1kW, the average cost of the solar panel ranges between £1800 to £1850, 2kW is between £3600 to £3700, solar panel size of 3kW ranges between £5500 to £5600 and finally, 4kW is between £6000 to £6050. For example, with the aforementioned prices in mind, the cost of solar panels for a standard 3 bedroom house will range between £5520 to £6040 as the high electricity demands will need the installation of 3 to 4kW solar system size.

Meanwhile the installation cost of solar batteries is also dependent on a number of influencing factors like the size as well as the make of the battery. Generally, you can expect to spend within the range of £500 to £2000 to install your batteries depending on aforementioned factors. In the event whereby you’ll be retrofitting, you might also need to include an additional cost of £1000 for an inverter. However, it’s important to note that there are only quite a few hybrid systems which are able to combine a battery storage with an inverter.

If you happen to live in a quiet, serene environment ( or just cherish being in one) and wish to have an air source heat pump installed on your property, then you’d probably want to know just how noisy these renewable energy source are. In this post, we aim to provide answers to this question and more. Let’s take a look!

There is no short and direct answer to this question as air source heat pumps are available in varying shapes and sizes which makes the sound as well as volume of their noise different between models and manufacturers. However, as a result of government regulations, most of the contemporary air source heat pumps are able to function a lot quieter when compared to the older models. As you would have expected, modern air source heat pumps shouldn’t produce more than a low whirring sound provided they’re functioning as they should with no faults. On the other hand, the volume of the sound generated is largely dependent on the amount of work the air source heat pump is doing. This implies that a greater work load will generate a louder noise. This is due to the fan’s speed which works to absorb warm air into the compressor.

In order not to disturb the neighbours, noise pollution is normally determined at the design stage of the air source heat pump installation. The unit to be placed outdoor will typically be positioned as far from the neighbours property as possible and it’s also a great idea not to put the box directly under any windows. Overall, it’s always advisable to go for the newer models which tend to be better designed with thicker chassis and quieter fans.

If you’re thinking about the possibility of installing a ground source heat pump in your home, then it’s normal to consider how efficient they’re in heating up a house before going ahead to make a purchase decision. In this article, we are going to address this question to help you make an informed purchase decision.

We know you’d prefer a single, accurate answer to this question, but the fact is, there are several influencing factors that can play a key role in the efficiency of a ground source heat pump installation. These factors include whether or not the property is well insulated, the fitting of a well designed system and the quality of its installation, the heat source that’s being used as well as the heating distribution system and its size ( under floor heating or radiators ).

The Coefficient of Performance ( CoP) measurement is used to imply the efficiency of a heat pump. This is basically the ratio between the amount of heat energy generated by the ground source heat pump and the amount of electrical energy or fuel it consumes. Therefore, the Seasonal Coefficient of Performance ( SCoP) is usually taken as a realistic measurement to cover throughout the year as its based on CoP at varying conditions as well as a standardized climate.

You must, however, note that there is no established Coefficient of Performance for ground source heat pumps as they can be influenced by a lot of factors as well as testing conditions. When they’re properly fitted, ground source heat pumps can achieve a quite high Coefficient of Performance.

Generally, a ground source heat pump can generate about 3 to 4 kilowatts (kW) of heat for every 1 kilowatt to electricity or fuel it consumes. It’s able to achieve a higher efficiency when compared to its counterparts by using the freely available heat energy from the ground.

Air source heat pumps work by absorbing heat from the outside air and transferring it inside to heat up your property.

An air source heat pump has an outdoor unit containing a refrigerant. This absorbs heat from the air and passes into a compressor, where the temperature is increased. The heat then transfers either into water, which feeds into your wet heating system, or into air, which is dispersed around your property.

Air source heat pumps need electricity to run, but this is to power the compressor rather than directly generate heat.

If you’re thinking about getting a solar thermal system for your home, it’s normal to consider the possibility of using the system for central heating. So is this viable? In this article, you’ll learn how solar thermal panels can be incorporated for heating. Let’s have a closer look!

Heating and hot water systems, on the average, takes up a sizeable part ( up to 70 percent) of our energy bills. Now take a moment to imagine how cool it’ll be to generate your own hot water for free without having to depend on any supplier which in turn significantly reduces your energy bills. Well, this is exactly the work of central heating systems that are powered by solar. That’s super cool, right? Well, let’s have a look at how this works.

While solar panels generates electricity, solar thermal panels produces heat for hot water production. However, what’s important is the fact that they both make use of the sun’s natural energy to provide us with a free and renewable energy we can use in our homes. Here’s how it works.

Solar thermal panels directed at central heating incorporates the sun’s natural energy to heat water in a storage cylinder which is then available for use at home. These solar thermal panels are exposed to the sunlight by fitting them on the roof of the home. Generally, they’ll include tubes that contains liquid whose job is to collect the heat and then transfer it to a hot water cylinder that’s solar compatible in your home. The heat is generated for free and is also renewable. This is help you save lots of money on oil, gas and even electricity which you purchase to power the cylinder.