Find a Renewable Energy Specialist you can trust in Braintree.

In a similar way to other major home improvement projects, some specific requirements must be met to allow for the installation of solar panels. The main reason why these standards and regulations were established is to minimize the risk of the solar system becoming an issue or potential hazard in the unforeseeable future. So if you’re thinking about buying and fitting new solar panels, you’ll probably want to know whether or not you’ll require to submit a planning permission application for approval before you can proceed.

Generally, solar panels are covered under what’s called “Permitted Development” which gives you the freedom to install your solar panels without having to apply for a planning permission. However, there are some exceptions to this rule. These exceptions include if your house is a listed building or if your house is located within a conservation area. In these exceptional cases, it’s possible that you’ll need to apply for a planning permission, but this will largely depend on the discretion of your Local Planning Authority. What’s more? Solar panels are usually subjected to normal building regulations which includes examining the roof to make sure that it can support the additional weight. You can call in a MCS certified installer to carry out this check for you.

In order to install your solar PV on your roof, you must follow these guidelines:

✓ Your solar panels shouldn’t go beyond the highest point of the roof (excluding chimneys).

✓ The solar panels shouldn’t project beyond 200mm off the roof’s edge.

✓ The solar panels should be removed once they’re no longer used to produce electricity

✓ The solar panels should be installed such that the area and building’s appearance change is minimized.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

There are two main types of air source heat pump: air-to-water and air-to-air. They work in different ways and have different advantages and disadvantages. Make sure you do your research so you know which one is best for you. Alternatively a registered installer will be able to determine the best type for your property.

Air source heat pumps can be a really efficient way to generate heat. Although they require electricity to run, they generate much more heat than an electric heater that uses the same amount.

Air source heat pumps provide heat at a lower temperature than most other types of space heating. This means they’re most efficient when they’re left on for longer periods of time, and distribute heat through wet heating systems with large surface areas, like underfloor heating or big radiators.

Air source heat pumps can be much more efficient than oil and LPG boilers, and older electric heating systems. However, they’re only usually the most efficient option if your property is very well insulated.

Solar panels provide an alternative to paying expensive National Grid energy rates, so primarily their first major benefit is helping to reduce bills. Solar PV panels will produce free electricity, whilst solar thermal panels generate heat for hot water and space heating. There are also payment incentives known as the Feed-in Tariff scheme (FITs) (for solar PV) and the Renewable Heat Incentive (for solar thermal) which guarantee a tax-free income for 20 years.

First and foremost let’s look at the meaning of a ground source heat pump. A ground source heat pump is simply a renewable heating system which happens to absorb the low temperature solar energy stored in the ground or in water with the help of a pipework that’s submerged and converts this energy into a higher temperature through compression. A ground source heating pump is capable of supplying the entire heating and hot water needs of a building throughout a whole year regardless of the season. So how exactly does a ground source heat pump work? Let’s have a look!

In principle, a ground source heating pump makes use of a refrigeration system but in a reverse form as it extracts low temperature heat from one point or location which is the source and transfer a higher temperature heat to another point or location - the sink. The pumps are powered by electricity and the operational principle can also be incorporated at generating both heating and cooling energy.

Knowing fully well heat naturally flows from warmer to cooler places, the ground source heat pump takes advantage of this physics by distributing a cold fluid via ground array pipework either in the ground or in water. It’s able to extract low grade energy from external sources of heat which includes soil, rock, lakes as well as streams.

Once the absorbed energy has been released to the heat pump from the ground or water, the fluid proceeds with its circuit back to the pipework to start its cycle all over again. Some of the benefits of the ground source heat pumps includes low carbon emission and improved air quality, efficient and affordable heating, the use of free heat from the ground and lots more.

Unlike the photovoltaic (PV) power which works to turn a part of the electromagnetic radiation of the sun directly to electrons and electricity, a solar thermal can simply be referred to as the absorption of the sun’s heat for human use. As a result, the solar thermal has a wider range of uses than the PV does in several ways. This is due to the fact that the sun’s heat can be absorbed and transported via a medium and the stored energy incorporated for several great purposes such as to heat water, to heat and cool a home or living space, to prepare a meal as well as to generate electricity. All these functions are useful for both residential and commercial spaces.

There are generally three different ranges of solar thermal energy that are being used which includes the low temperature ( for heating, cooling as well as ventilation), the mid temperature ( used for preparing meals, heating hot water and the likes) as well as the high temperature ( used for generating electricity). To focus more on generating electricity, there are a wide array of ways through which the sun’s heat can be directed at creating electricity via a heat exchanger which operates to super heat water or inert gas to power an electricity- generating plant or to produce electricity via a Stirling engine.

In order to increase their output or make them more efficient, evacuated glass tubes are used to encircle the tubes which in turn helps them to collect more heat energy while also protecting them from re-radiating the heat energy absorbed. The trough are normal positioned north to south as well as to keep tabs on the travels of the sun throughout the day.

Air source heat pumps are a type of heating system that you can use to warm the air in your property. They’re a semi-renewable energy generator as, although they use electricity, they extract and use renewable heat from the air.

There are two main types of air source heat pump – air-to-water, and air-to-air. Air-to-water heat pumps are the most popular, and are best used to heat water that supplies underfloor heating systems or large radiators. Air-to-air pumps heat air, which is then dispersed round your property using fans.

Do you want a low carbon way of heating your home? Then, getting an air source heat pump is the way to go! What they do is pretty simple - they absorb the potential thermal energy present in the outside air and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. In other words, it functions by extracting heat from a cooler place and then uses it to raise the temperature inside a home or property. Being very similar to air conditioning units, the amount of heat they’re going to produce for your home or property will be dependent on the size you install. Therefore, the bigger the heat pump, the more the heat that’ll be generated.

Air source heat pumps have two main types which includes air to air and air to water. Air-to-water heat pumps works by absorbing heat from the outside air, then relays it directly into your home or property through the help of fans. In order to move the heat around your home, you’ll need a warm air circulation system. This type of air source heat pump are not eligible for the government’s Renewable Heat Incentive Payment as they can’t generate hot water. What’s more? They can function in reverse during the hot summer months.

Air-to-water heat pumps, on the other hand, operates by extracting heat from the outside air and transmitting it into the wet central heating system. Due to the fact that they’re able to generate heat that’s cooler than the one generated by a conventional gas or oil boiler, they happen to be a better fit for larger radiators or water underfloor heating.