Find a Renewable Energy Specialist you can trust in Magherafelt.

Biomass boilers will work with existing central heating systems, presuming this is not decades old, whether they use radiators or under floor heating. A surveyor will check the existing system you have in place before quoting for or recommending a biomass boiler to you.

The bigger the ground source heat pump, the better right? Wrong! And you’ll definitely be sorry to make such a huge mistake. When planning to install a heat pump, determining the size of the ground source heat pump is not as direct and straightforward as many homeowners would think. Here, you’ve got only a small margin for error. When the pump is too small, the heat pump will make use of the backup heater too often and in the event whereby the heat pump is too big, it’s going to short cycle. Both situations are preferably avoided as they’ll both leave you with an expensive and inefficient system.

To get the accurate size of a heat pump, there’s usually the need to hire the services of an expert and licensed heat pump installer who possesses a top notch design calculation software. In reality, the majority of inefficient systems are caused by a lack or poor understanding of the suitable design software.

There are many factors that can influence the calculation of a home’s heat pumps size. These includes

✓ Radiators and underfloor heating sizes

✓ Insulation, property fabric as well as heat loss

✓ The number of rooms in the property

✓ The types of rooms and their uses.

✓ The desired indoor temperature for varying rooms

✓ Seasonal temperature fluctuations.

Generally, a bigger house will require a bigger ground source heat pump. With an eye on the age of the property, heat loss as well as the types of the rooms, a house of about 100 square metre can require up to 4kW ground source heat pump. And for a house that’s about 200 square metre, the ground source heat pump also doubles to 8kW.

First and foremost let’s look at the meaning of a ground source heat pump. A ground source heat pump is simply a renewable heating system which happens to absorb the low temperature solar energy stored in the ground or in water with the help of a pipework that’s submerged and converts this energy into a higher temperature through compression. A ground source heating pump is capable of supplying the entire heating and hot water needs of a building throughout a whole year regardless of the season. So how exactly does a ground source heat pump work? Let’s have a look!

In principle, a ground source heating pump makes use of a refrigeration system but in a reverse form as it extracts low temperature heat from one point or location which is the source and transfer a higher temperature heat to another point or location - the sink. The pumps are powered by electricity and the operational principle can also be incorporated at generating both heating and cooling energy.

Knowing fully well heat naturally flows from warmer to cooler places, the ground source heat pump takes advantage of this physics by distributing a cold fluid via ground array pipework either in the ground or in water. It’s able to extract low grade energy from external sources of heat which includes soil, rock, lakes as well as streams.

Once the absorbed energy has been released to the heat pump from the ground or water, the fluid proceeds with its circuit back to the pipework to start its cycle all over again. Some of the benefits of the ground source heat pumps includes low carbon emission and improved air quality, efficient and affordable heating, the use of free heat from the ground and lots more.

How Much To Install Solar Panels And Battery?

Are you thinking about installing solar panels and battery in your home and wondering how much the installation is going to cost? Well, you’re not alone. This is one of the most commonly asked questions in the solar world, but unfortunately a precise answer can not be provided. This is mainly due to the fact that solar panel systems come in varying sizes which is the main influencing factor that determines how much electricity that can be generated. In other words, the larger the system, the more the electricity that’ll be produced to your home’s benefit.

Generally, for a solar system size of 1kW, the average cost of the solar panel ranges between £1800 to £1850, 2kW is between £3600 to £3700, solar panel size of 3kW ranges between £5500 to £5600 and finally, 4kW is between £6000 to £6050. For example, with the aforementioned prices in mind, the cost of solar panels for a standard 3 bedroom house will range between £5520 to £6040 as the high electricity demands will need the installation of 3 to 4kW solar system size.

Meanwhile the installation cost of solar batteries is also dependent on a number of influencing factors like the size as well as the make of the battery. Generally, you can expect to spend within the range of £500 to £2000 to install your batteries depending on aforementioned factors. In the event whereby you’ll be retrofitting, you might also need to include an additional cost of £1000 for an inverter. However, it’s important to note that there are only quite a few hybrid systems which are able to combine a battery storage with an inverter.

Solar panels provide an alternative to paying expensive National Grid energy rates, so primarily their first major benefit is helping to reduce bills. Solar PV panels will produce free electricity, whilst solar thermal panels generate heat for hot water and space heating. There are also payment incentives known as the Feed-in Tariff scheme (FITs) (for solar PV) and the Renewable Heat Incentive (for solar thermal) which guarantee a tax-free income for 20 years.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

Tesla’s top-of-the-range battery storage system is still one of the most expensive on the market. It has a huge 13.5kWh usable capacity and can even keep you up and running during a power cut. But how long does a Tesla Powerwall battery last? And does this mean it’s worth investing in one?

The Tesla Powerwall 2.0 comes with a 10-year warranty. But Tesla says that it should last way beyond this – at least 5 years longer. The standard warranty says that it should work at 70% capacity for the full 10 years – so if it loses more than 30% of its storage capacity within that time, it should still be covered.

While the Tesla Powerwall does last a long time, it has a large capacity that most average households won’t require, and it’s a costly option. After installation, the Powerwall 2.0 will set you back between £6,500 and £9,000, so ideally you want it to last past its 10-year warranty.

Before you splash out, consider the size of the solar panel system you want to install or you already have. Will it generate enough electricity to make it worth storing in the Powerwall? If not, are you expecting to upgrade your solar panels to a larger system in the future? If you are, then it might be worth investing in a Powerwall. It might also be better to wait until you come to upgrade your solar panels – the solar battery price trend is going the same way as solar panels, so they will probably continue to decrease in price as more people adopt the technology.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.