Find a Renewable Energy Specialist you can trust in Durham.

So do you wish to take advantage of the heat generated by the ground to warm up your home by getting a ground source heating pump? If yes, then you’d also probably be wondering how much a ground source heat pump is going to cost so you can set a budget and start planning.

Installing and running ground source heat pump can cost between the range of £600 to £700 to run on an annual basis, meanwhile it can cost you within a range of £13,000 to £19,000 to have installed. However, you should take note that these prices can be by varying influencing factors such as the size of the installation as well as any other extra work that may needed to complete the job.

When it comes to estimating the time it takes to recover the initial cost of the system via energy savings, nothing is certain as this can be very hard to determine or predict. The main reason for this is due to the fact that it’s dependent on the efficiency of your heating system, the type of system you’re replacing ( whether or not you qualify for Renewable Heat Incentive -RHI payments ), the efficiency of your home’s insulation, how efficiently the system’s controls are being used and how the heat generated from the ground source heat pump would be put to use. However, to figure out how much you’ll save, the type of fuel replacing is perhaps the most essential. For a four bedroom detached house, you can save between a range of £1,200 to £1,300 for a LPG fuel replaced, £1,400 to £1,500 for an electricity fuel replaced, £600 to £700 for an oil fuel replaced and finally, £200 to £300 for a solid fuel replaced.

Not only will you reduce your electricity bill by generating your own electricity with solar panels, but you can also earn money through the SEG which is offered by large energy suppliers. They’ll pay you for the electricity you export back to the grid. You’ll also reduce your carbon footprint, lessening your impact on the environment.

Whether installing an air source heat pump will help you save money depends on your property, how long you expect to live there, and the type of heat pump you get.

Air source heat pumps are initially quite expensive to install. However, if you get an air-to-water air source heat pump, you’re eligible for money from the Renewable Heat Incentive [https://www.energysavingtrust.org.uk/scotland/grants-loans/renewables/renewable-heat-incentive] (RHI). This is a UK government scheme that gives you quarterly cash payments over seven years if you install an eligible renewable heating technology (air-to-air air source heat pumps aren’t included).

All this means that if you have long-term plans to stay in your property, then an air-to-water air source heat pump can be a great way to save money on your heating bills. However, if you’re planning on moving out of your property relatively soon, or are a considering an air-to-air air source heat pump, it may not be the best financial option for you.

It’s important to remember that air source heat pumps are at their most efficient when installed in very well insulated properties. If your property’s not very energy efficient, you may find that a heat pump won’t help you save money.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

Solar panels provide an alternative to paying expensive National Grid energy rates, so primarily their first major benefit is helping to reduce bills. Solar PV panels will produce free electricity, whilst solar thermal panels generate heat for hot water and space heating. There are also payment incentives known as the Feed-in Tariff scheme (FITs) (for solar PV) and the Renewable Heat Incentive (for solar thermal) which guarantee a tax-free income for 20 years.

How To Install Solar Panels And Batteries

Have you decide to purchase a solar system for your home and wondering how to go about the installation? If yes, then we’ve got you covered! In recent times, it’ll be totally safe to say that solar panels and batteries for home use in the UK has now become more of a necessity than a luxury considering the numerous benefits the system offers. However, with the cost of having the system installed, you might be forced to think about the doing the installation yourself.

If you lack proper training and experience in the solar system installation process, it’s advisable to hire the services of a qualified technician who can guarantee the best results the first time and help you save time and extra costs that may result from possible costly errors. Here, we’ll give you a good insight into the installation process.

• Mount the solar panel and ensure it’s properly screwed to your roof. Try to position in such a way that it faces direct sun rays to have enough solar power generated.

• Connect your charge controller. The current that’s being generated by the solar panels will not be stable all day long. As a result, it’s important to avoid connecting solar photo voltaic modules directly to your better, if you don’t want it damaged. To control the current received from the solar panels, the charge controller is required. It has three connecting points - one for the battery, one for the solar panels and the last for Direct Current (DC) identify the one for solar panels and connect accordingly.

• Connect the battery to charge controller. The charge controller possess two terminals for the battery - the positive and negative terminals. Connect the positive terminal to the positive of the battery and also do the same for the negative.

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.