Find a Renewable Energy Specialist you can trust in Galston.

If you’re thinking about the possibility of installing a ground source heat pump in your home, then it’s normal to consider how efficient they’re in heating up a house before going ahead to make a purchase decision. In this article, we are going to address this question to help you make an informed purchase decision.

We know you’d prefer a single, accurate answer to this question, but the fact is, there are several influencing factors that can play a key role in the efficiency of a ground source heat pump installation. These factors include whether or not the property is well insulated, the fitting of a well designed system and the quality of its installation, the heat source that’s being used as well as the heating distribution system and its size ( under floor heating or radiators ).

The Coefficient of Performance ( CoP) measurement is used to imply the efficiency of a heat pump. This is basically the ratio between the amount of heat energy generated by the ground source heat pump and the amount of electrical energy or fuel it consumes. Therefore, the Seasonal Coefficient of Performance ( SCoP) is usually taken as a realistic measurement to cover throughout the year as its based on CoP at varying conditions as well as a standardized climate.

You must, however, note that there is no established Coefficient of Performance for ground source heat pumps as they can be influenced by a lot of factors as well as testing conditions. When they’re properly fitted, ground source heat pumps can achieve a quite high Coefficient of Performance.

Generally, a ground source heat pump can generate about 3 to 4 kilowatts (kW) of heat for every 1 kilowatt to electricity or fuel it consumes. It’s able to achieve a higher efficiency when compared to its counterparts by using the freely available heat energy from the ground.

Air source heat pumps are a type of heating system that you can use to warm the air in your property. They’re a semi-renewable energy generator as, although they use electricity, they extract and use renewable heat from the air.

There are two main types of air source heat pump – air-to-water, and air-to-air. Air-to-water heat pumps are the most popular, and are best used to heat water that supplies underfloor heating systems or large radiators. Air-to-air pumps heat air, which is then dispersed round your property using fans.

Do you want a low carbon way of heating your home? Then, getting an air source heat pump is the way to go! What they do is pretty simple - they absorb the potential thermal energy present in the outside air and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. In other words, it functions by extracting heat from a cooler place and then uses it to raise the temperature inside a home or property. Being very similar to air conditioning units, the amount of heat they’re going to produce for your home or property will be dependent on the size you install. Therefore, the bigger the heat pump, the more the heat that’ll be generated.

Air source heat pumps have two main types which includes air to air and air to water. Air-to-water heat pumps works by absorbing heat from the outside air, then relays it directly into your home or property through the help of fans. In order to move the heat around your home, you’ll need a warm air circulation system. This type of air source heat pump are not eligible for the government’s Renewable Heat Incentive Payment as they can’t generate hot water. What’s more? They can function in reverse during the hot summer months.

Air-to-water heat pumps, on the other hand, operates by extracting heat from the outside air and transmitting it into the wet central heating system. Due to the fact that they’re able to generate heat that’s cooler than the one generated by a conventional gas or oil boiler, they happen to be a better fit for larger radiators or water underfloor heating.

There are a few factors that will determine whether it’s worth getting a solar battery. They involve how much electricity you use, how often you’re at home and whether you receive any export payments.

To work out whether it’s worth getting a solar battery, you need to work out how much of the electricity you generate you’re using already. If you’re able to run all your appliances during the day while your solar panels generate electricity, then it sounds like you’re already using your electricity well. It might not be worth you getting a solar battery in this case.

However, if you’re not at home for a lot of the day, then you’ll be missing out on the electricity your panels are generating while the sun’s shining. If you install a solar battery system, you can store the electricity that your panels generate in the battery and use it when you get home. This will help you cut your electricity bills even further.

You’ll also need to consider whether you’re getting paid to export your electricity. If you’re on the Feed-in Tariff scheme (FITs) or receive payments from the Smart Export Guarantee (SEG), you’ll get paid for every unit of electricity you export to the National Grid. Before you decide whether it’s worth getting a solar battery, you’ll need to weigh up whether you’d be better off carrying on exporting your unused electricity rather than storing it to use yourself. If you’re unsure, visit the Energy Saving Trust’s website or speak to an MCS-registered installer who will be able to help you work out which is more cost-effective.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

Air source heat pumps work by taking heat from the air and using it to heat your home. They absorb heat from the air into a fluid, which then goes to a compressor where it gets hotter. This heat is then used to warm up water or air, which is distributed around your home.

First and foremost, you should know that heat pump is simply a device whose primary function is the transmission of thermal energy from one spot to the other. A good example can be found in the refrigerators whereby the evaporation as well as cooling of a liquid is incorporated to lower the storage compartment’s temperature. In recent times, this whole technology is utilized to draw the potential thermal energy present in the air outside and transmit it directly to the home or property where it’s going to be compressed and the heat transferred with the help of a number of coils. This is exactly what an air source heat pump does as it absorbs heat from the air and convert it into a higher temperature using a compressor. How the air source heat pump works is really simple, it’s just like a refrigerator but in reverse. Let’s take a look!

• The air source heat pump extracts heat present in the outside air into a liquid refrigerant at a reduced temperature.
• The pump then compresses the liquid to increase its temperature with the help of electricity. Once done, it then compresses it back to liquid so as to free the heat stored.
• The heat released is then directed to the radiators or under floor heating, while the ones left would be stored in the hot water cylinder.
• The hot water that’s stored can be used for showers, baths as well as taps.

Overall, the air source heat pump is an efficient way to make your home warm. It makes use of electricity to function, but it should consume lower electrical energy than the heat it generates.

• The power of your solar panel system – there's no point buying a higher capacity battery if your system will never generate enough electricity to charge it
• How often you think you will need to charge your battery
• Your budget
• Whether you care about having the latest technology and a recognisable brand name

When you’re about to transform from the standard electricity to solar energy, what determines your solar system’s size is the amount of solar that’s required. The amount of solar that you’ll need, on the other hand, requires considering the end goal, be it to increase money savings, reduce environmental contamination, maximize Returns On Investment ( ROI), or just to copy what the neighbour’s done.

In order the determine the number of solar panels that is needed, the first step would be to calculate the number of kWhs that’s currently being used. A kWh is what’s used to determine the amount of energy that has been incorporated over time which the utility uses to bill you. What’s strongly recommended to create a suitable range is a 6 to 12 months average of your household electricity bill. Other factors that can play a key role in the determination of the number of solar panel needed include the following:

✓ Sunlight exposure hours. In order to know just how much energy your solar panels will generate, there’s a need to know the number of direct sunlight hours you should expect on a daily basis. For example if you stay in a region that’s usually very sunny, then it’ll be reasonable to expect more energy production per panel than regions that are usually cloudy.

✓ Angle and size of the roof. Roofs with a lot of workable space may require to let go of some efficiency opting for larger and cost effective panels to achieve the targeted energy. However not all homeowners have sufficient roof space or shade coverage for the solar panel they actually want. Also, the degree at which the roof slants will also determine if the sunlight is hitting the panels well enough and the amount of energy that can be generated thereof.

If you’re looking to purchase and install a solar system for your home or property, then knowing the amount of energy a solar panel can produce can go a long way to help you determine just how much solar panels that’ll be needed to power your entire house. In this article, we’ll give you an idea of the amount of energy that can be generated by a solar panel to help you make informed decisions going ahead.

First and foremost, you should note that each and every solar panel is rated by how much direct current power they’re able to generate under standard testing conditions. The output of a solar panel is given in watts units (W) and it stands for the theoretical power generation of the panel under direct sunlight as well as temperature conditions. Generally, several domestic solar panels possesses power output ratings which ranges from 250 watts to 400 watts. And as you would have expected, the higher power ratings are preferable when compared to the lower power ratings. What’s more? The total wattage of your solar panels will greatly influence a major part of your overall solar system cost.

Assuming you’re able to get just about 5 hours of direct sunlight every day, you can determine the output of your solar panel in this way - 5 hours x 290 watts ( wattage example of a premium solar panel) = 1450 watts-hours or approximately 1.5 kilowatts per hour (kWh). hence, the individual solar panel output in your array should be able to generate about 500 to 550 kWh of energy every year. This is sufficient energy to power some small appliances without problems.