Find a Plasterer you can trust in Warwick.

Also commonly referred to as drywall, plasterboard is an incredibly versatile product which features a sandwich of gypsum plaster between thick paper layers. It’s mainly used on both walls and ceilings due to the wide range of benefits it provides. Not only can plasterboard be made to be humidity resistant, fire resistant as well as noise resistant, but they’re also known to have a low environment impact, easy to repair and can be used to conceal stuff from plain sight. As a result of these benefits couple with the fact that they also happen to be quite affordable, plasterboard has grown to become a ubiquitous phenomenon in modern residential buildings.

When it comes to the installation of plasterboard on ceilings, one of the major sources of concern for several homeowners is the determination of the thickness required to ensure a durable and long-lasting project. If you’re planning to fit plasterboard on your ceiling and wondering the thickness that’ll be appropriate, then you’ve come to the right place. In this post, we’re going to give you a good insight on what plasterboard to use for ceilings. Let’s take a look!

First and foremost, the standard plasterboard sheet size is 120 cm in width and within the range of 180 cm to 360 cm in height. These sizes are designed to provide the much-needed support to the standard stud spacing which is 160 cm. Depending on the manufacturer, plasterboard can be in four different widths. Now talking about the thickness, there are two standard thicknesses of plasterboard - 9.5 mm and 12.5 mm. The sizes of plasterboard for ceilings are 9.5 mm or 10 mm. Most individuals tend to assume that the thicker the plasterboard the better, but this is absolutely false. A thicker plasterboard will only stick harder to the ceiling which will make it hard to seal joints if required.

Artex was originally made using white asbestos to make it stronger. However, this stopped in the mid-1980s, and the use of asbestos was banned in the UK in 1999, due to its extreme health risks. So, any artex you buy today won’t contain asbestos.

If you have an artex ceiling or wall that was created before 1999, it may have asbestos in it. This won’t be a health hazard if you leave it undisturbed, so it’s not necessary to remove it. However, if you want to get rid of or alter your artex ceiling or wall, you must get it tested to check if it has asbestos in or not first. If it does, you’ll need to hire a qualified professional to work on it.

Artex is a water based decorative surface coating is typically incorporated on both walls and ceilings so as to apply a pattern. During the peak of its popularity in the 1970’s, it was considered the height of fashion when it comes to interior wall designs however its major drawback remains the fact that it usually contains asbestos especially if it was manufactured before the laws governing the use of asbestos was changed in the year 2000. And asbestos, as we know it, can be deadly when disturbed and its fibres are inhaled.

If you have artex installed in your purchased property and you do not know when the artex walls were done, or perhaps you just want to change the aesthetic design of your home into something more modern and to your personal taste, then you may want to remove the existing artex from your property for good. If this is your wish then you’ve come to the right place.

To remove artex from your walls you can choose to do so using the steaming method or through the use of an external product.

Using the steaming method, you should know that it’ll be more labour intensive and time consuming. You need a lot of patience moving your steamer slow and steady because if left on a spot for too long can damage the wall behind the coating. Once the artex has been dampened with the steamer, you can then scrape them off with a handheld scraper.

A faster solution would be to use an external product to remove your artex.  For example, you can use X-Tex which is a water-based coating remover. All you need to do is paint the substance over your artex wall and leave to dry for about 30 to 60 minutes before peeling away the artex.

Artexing a ceiling can be a tricky job, but whether you’re considering hiring a professional or DIY, it’s helpful to know how it’s done.

Artex is available either in a paste or powder form. The paste is ideal if you’re making small repairs or additions to an existing ceiling. But, if you have a whole ceiling to cover, the powder is more cost effective. When you’re ready to get started, you’ll need to mix the powder up with cold water according to the instructions.

It’s possible to artex over plaster, plasterboard or paint. If you have a plasterboard surface, you should tape and fill any joints or cracks before you begin. Plaster and plasterboard both require a coat of sealant or primer first. You can usually artex straight over paint, but any gloss paint should be sanded down, and any dark paints covered with a layer of white.

Artexing can get quite messy, so make sure you empty the room you’re working in as much as possible, lay down sheets and wear protective clothing and glasses. You might want to practice on a piece of board before you start on the ceiling.

Start by using a brush or roller to cover a 500 square cm area with a generous layer of artex. Then use a brush, comb or roller to create your chosen texture. Every time you do a new section of ceiling, try to blend it with the other sections you’ve done. Don’t be tempted to cover the whole ceiling before you start adding texture – the artex will dry too quickly for you to do it all in time.

Artex usually needs 12-24 hours in a well-ventilated space to dry completely.

Installing a plasterboard to a ceiling is not the easiest of tasks, and even though it can be done by one person, it’s usually a lot easier when done by two people. If you’re an experienced DIYer, this task becomes a lot easier to undertake, with both confidence and patience needed to ensure a successful outcome. If you lack these essential attributes, we’d strongly recommend you call in a reliable professional who can guarantee the best results for help. In this guide, we’re going to take you through the processes involved to plasterboard your ceiling. Let’s take a look!

✓ Take a measurement of your ceiling. Knowing the length and width of your room is crucial here. You have nothing to worry about if it’s not a perfect square as that’ll only mean more cutting.

✓ Make the necessary plasterboard cuts. Cut the plasterboard sheet with a utility knife in accordance to ceiling space measured.

✓ Remove existing plaster. Once done, examine the trusses and beams to ensure they’re still in a great condition before you proceed. Also, make sure there’s no loose plaster that can compromise your new installation.

✓ Apply construction adhesive. For a better fit, you’d have to apply adhesive along the beams while also avoiding the edges as this could affect your screw placement.

✓ Start in a level corner. You have to start the installation from the most level corner.

✓ Work along the outside edges. Secure it using a screw along the outside edge. This will make your plasterboard held to your ceiling perfectly. It won’t bend or break as your proceed with the installation.

✓ Complete the installation. Install the plasterboard on your entire ceiling and complete the installation by taping the seams and plastering for a smooth surface.

The short and simple answer to this question is, it depends. Artex surface coating was manufactured with white abestos ( until the mid 1980’s ) in order to strengthen as well as harden it. In other words, this implies that all the ceilings and walls coverings made by Artex Ltd and other manufactures at the time are highly likely to contain asbestos. Although Artex Ltd stopped using asbestos as early as the mid 1980’s, there were still other manufacturers who continued using it until 1999 when the laws and regulations covering the use of asbestos changed in the year 2000.

Asbestos, however, is only harmful when disturbed and releases its deadly fibres. For instance, when it’s being sanded and removed as it usually poses no risks when left undisturbed. Since it’s not possible to identify Artex containing asbestos fibres with the naked eye, it’s strongly recommended that you hire the services of a qualified person or company to help determine if you have asbestos in your ceilings or walls especially if your house was constructed before the year 2000. The professionals will be able to advise you on the best course of action as well as if it’s dangerous.

To be sure if your Artex contains asbestos, you’ll need to have the artex sampled by an asbestos surveyor. If you’re planning to have a construction or maintenance work done on your property, and the artex is likely to be in the way or disturbed, there’s a need for you to have a refurbishment or demolition asbestos survey done. This will ensure that all the areas that’ll be disturbed by the work is properly tested to determine the presence or otherwise of asbestos. If found, the artex will have to be addressed and either removed or protected before any work can take place.

Artex simply refers to a surface coating that’s commonly incorporated for interior decorating. Although it’s usually found on ceilings but it can also be used on the walls as well. The surface coating enables the professional plasterer or decorator add both texture as well as patterns to it. Originally, the name “Artex is the trademark of a UK based company known as Artex Ltd. Over time, the Artex name has been used to refer to all textured coatings, although there are other businesses that manufacture and sell identical products.

You can find Artex on ceilings as well as walls of mainly residential properties. In the 70’s and 80’s, it was pretty much a trend to have either your wall or ceiling ( can be both ) covered with Artex. The surface coating can be incorporated to create raised, textured swirls as well as patterns on ceiling and walls. There are a number of different patterns that can be made using Artex and some of these includes the following: Broken leather, swirl, stipple, fan or shell as well as knifed plaster. It can also provide just a bobbly raised uneven patter appearance from top to bottom.

Artex is main put to use by mainly decorators ( mostly plasterers). This is a skilled job as it’s tedious to create uninformed patterns especially if you don’t know how or where to start. Although the skill of Artex is very much a trade that’s dying rapidly now, but it was pretty much in high demand especially in the 70’s and 80’s. Nowadays, homeowners now prefer smooth plastered finishes over Artex, as they can be easily painted or wallpapered.

Plasterboard or drywall is simply gypsum plaster covered from both sides by thick paper layers. It’s known to be a highly versatile product used on both interior walls and ceiling as a result of its numerous advantages. This popular material in residential buildings can be designed to be fire resistant, humidity resistant and noise resistant. They have a low impact on the environment, while also being quite easy to repair and perfect to hide stuffs from plain sight. Most home and property owners in the UK have this material installed in their space as despite the multiple benefits, they’re also quite affordable. However, if you’re thinking about installing a plasterboard on your ceiling, one challenge you’re likely to face is determining the appropriate plasterboard thickness to incorporate as this make or mar your entire project. In this post, we’re going to take a look at the right plasterboard thickness for ceiling so as to help you make an informed decision moving forward. Let’s take a look!

Firstly, let’s consider the size of the plasterboard sheet. The standard plasterboard sheet size is 120 cm in width and within the range of 180 cm to 360 cm in height. These sizes are designed to provide the much-needed support to the standard stud spacing which is 160 cm. Depending on the manufacturer, plasterboard can be in four different widths. Now talking about the thickness, there are two standard thicknesses of plasterboard - 9.5 mm and 12.5 mm. The sizes of plasterboard for ceilings are 9.5 mm or 10 mm. Most individuals tend to assume that the thicker the plasterboard the better, but this is absolutely false. A thicker plasterboard will only stick harder to the ceiling which will make it hard to seal joints if required.