Find a Plasterer you can trust near you.

Artex simply refers to a surface coating that’s commonly incorporated for interior decorating. Although it’s usually found on ceilings but it can also be used on the walls as well. The surface coating enables the professional plasterer or decorator add both texture as well as patterns to it. Originally, the name “Artex is the trademark of a UK based company known as Artex Ltd. Over time, the Artex name has been used to refer to all textured coatings, although there are other businesses that manufacture and sell identical products.

You can find Artex on ceilings as well as walls of mainly residential properties. In the 70’s and 80’s, it was pretty much a trend to have either your wall or ceiling ( can be both ) covered with Artex. The surface coating can be incorporated to create raised, textured swirls as well as patterns on ceiling and walls. There are a number of different patterns that can be made using Artex and some of these includes the following: Broken leather, swirl, stipple, fan or shell as well as knifed plaster. It can also provide just a bobbly raised uneven patter appearance from top to bottom.

Artex is main put to use by mainly decorators ( mostly plasterers). This is a skilled job as it’s tedious to create uninformed patterns especially if you don’t know how or where to start. Although the skill of Artex is very much a trade that’s dying rapidly now, but it was pretty much in high demand especially in the 70’s and 80’s. Nowadays, homeowners now prefer smooth plastered finishes over Artex, as they can be easily painted or wallpapered.

How To Plaster A Wall

In order to plaster your wall successfully, you’ll firstly need to get the appropriate tools and materials for the job in place. The tools you’ll need to have includes a trowel and bucket trowel, plasterer’s float, corner trowel, hawk board, two buckets, mixing stick or a paddle, adequate plaster, PVA , dust sheets, clean water, sandpaper, stilts or step ladder as well as a dust mask.

✓ Prepare the wall. You’d have to make sure that you lay down a dust sheet so as to protect your floor and also gather any possible spillage or debris of plaster, before you start working on the walls. Get rid of all the dirt, dust and debris as this is very important for the success of your project if you’re going to be plastering on a worn out and old wall. Also, cover the holes and cracks in the walls with a screen tape

✓ Apply PVA to the wall. This will help ensure the layer you’re using will not dry out at the same time.

✓ Mix the paster. Mix the plaster according to the instructions given in the manufacturer’s manual.

✓ Apply the plaster onto the wall. Upon cleaning of the walls and successful mixture of the plaster, the next step is to apply the mixture to the wall using the hawk board, trowels and a floating tool.

✓ Skim and smooth. After the the first coat has dried after waiting for about 30 minutes, the next step will be to wipe out the bumps and lumps using a trowel to smooth over the surface. Once this is done you can then scrape the wall with a devilling float.

✓ Apply the second coat of plaster

✓ Apply the finishing touches. This includes polishing your work by adding some water to the surface with a spray gun and using the trowel to further smoothen out the surface.

✓ Painting and wallpapering.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

✓ Firstly, you need to put the plasterboard sheet flat on a firm surface.

✓ Use the tape measurement to measure the cut you wish to make.

✓ With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

✓ Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

✓ Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

✓ The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

✓ Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

✓ Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

✓ Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

The short and simple answer to this question is, it depends. Artex surface coating was manufactured with white abestos ( until the mid 1980’s ) in order to strengthen as well as harden it. In other words, this implies that all the ceilings and walls coverings made by Artex Ltd and other manufactures at the time are highly likely to contain asbestos. Although Artex Ltd stopped using asbestos as early as the mid 1980’s, there were still other manufacturers who continued using it until 1999 when the laws and regulations covering the use of asbestos changed in the year 2000.

Asbestos, however, is only harmful when disturbed and releases its deadly fibres. For instance, when it’s being sanded and removed as it usually poses no risks when left undisturbed. Since it’s not possible to identify Artex containing asbestos fibres with the naked eye, it’s strongly recommended that you hire the services of a qualified person or company to help determine if you have asbestos in your ceilings or walls especially if your house was constructed before the year 2000. The professionals will be able to advise you on the best course of action as well as if it’s dangerous.

To be sure if your Artex contains asbestos, you’ll need to have the artex sampled by an asbestos surveyor. If you’re planning to have a construction or maintenance work done on your property, and the artex is likely to be in the way or disturbed, there’s a need for you to have a refurbishment or demolition asbestos survey done. This will ensure that all the areas that’ll be disturbed by the work is properly tested to determine the presence or otherwise of asbestos. If found, the artex will have to be addressed and either removed or protected before any work can take place.

Can You Plaster Over Artex?

The short and simple answer to this question is yes, you can plaster over Artex. However, you must also note that plastering over Artex may not be the best choice as Artex is porous and as such, you’d have to detach the stripping so as to get a smooth and even coating. In the event whereby your ceilings or walls have Artex on them, you’ll have to smooth the Artex in order to obtain a plaster of solid coat.

✓ Preparing Artex for plastering. First and foremost, you’ll have to detach any bumps before you can plaster over the Artex. Do note that you don’t have to completely remove the Artex, all that’s needed is just enough to get a coat of plaster. Make use of a scraper to get rid of the bumps on various Artex designs like swirl and bark. Once you’re through getting rid of as much bumps as possible, there’s the need to seal the Artex due to the fact that it can absorb the moisture out of the plaster which will cut the time to get a good finish to little or nothing. You can use a PVA and water mix to do the job!

✓ The PVA mix. This is done to seal off the porous Artex in order to stop it from absorbing moisture from your plaster which can make it start to crack and crumble. To do this, simply mix half PVA and half water, then use a brush to paint the mixture over the plastering area. Once done, you can give the plastering surface about two to three coats and wait for the solution to dry off within a hour or two.

Plastering over Artex is not as hard as it seems, but if you lack the confidence to complete the task, simply contact a professional for help.

Installing a plasterboard on your ceiling is a cool way to modernize your property. Over the past couple of decades, there has bee an increasing number of trends associated with plastering of both walls and ceilings such as rounded edges and textured plaster. However, in recent times, home and property owners are now looking to install more of sharp edges. If you’re planning to plaster your ceiling, you’d probably want to know just how much this project is going to cost. If yes, then you’ve come to the right place. In this article, we’ll give you a rough estimate of ceiling plastering costs.

There are a plethora of factors the can influence the price of plastering your ceiling. These pricing components includes the following:

✓ Size. As you would have expected, the larger the job, the more the overall cost. However, the price per square metre will reduce which means that the cost of plastering a small ceiling space will cost more per square metre than the cost of plastering a larger ceiling space per square metre.

✓ Materials. We have a wide range of plasterboard available in the market. If you need a fire retardant, acoustic or other types of specialist plasterboard, you can expect to pay higher than standard plasterboards.

✓ Location. Just like many other home improvement projects, the cost of plastering ceiling varies greatly throughout the UK. Places such as London and the South East have the highest prices due to the high standard of living as well as greater demands.

In general, to plaster a ceiling (small 2 m x 2 m) - overboard and plaster will cost within the range of £200 to about £300. Also, to plaster a ceiling (large 5 m x 6 m) - overboard and plaster will cost within the range of £400 to about £600. The average plasterer’s daily rate (including material) is about £180 to £300 and ceiling plastering cost per square metre ranges between £20 to £40.

Artex is a water based decorative surface coating is typically incorporated on both walls and ceilings so as to apply a pattern. During the peak of its popularity in the 1970’s, it was considered the height of fashion when it comes to interior wall designs however its major drawback remains the fact that it usually contains asbestos especially if it was manufactured before the laws governing the use of asbestos was changed in the year 2000. And asbestos, as we know it, can be deadly when disturbed and its fibres are inhaled.

If you have artex installed in your purchased property and you do not know when the artex walls were done, or perhaps you just want to change the aesthetic design of your home into something more modern and to your personal taste, then you may want to remove the existing artex from your property for good. If this is your wish then you’ve come to the right place.

To remove artex from your walls you can choose to do so using the steaming method or through the use of an external product.

Using the steaming method, you should know that it’ll be more labour intensive and time consuming. You need a lot of patience moving your steamer slow and steady because if left on a spot for too long can damage the wall behind the coating. Once the artex has been dampened with the steamer, you can then scrape them off with a handheld scraper.

A faster solution would be to use an external product to remove your artex.  For example, you can use X-Tex which is a water-based coating remover. All you need to do is paint the substance over your artex wall and leave to dry for about 30 to 60 minutes before peeling away the artex.

How Much Does Plastering Cost?

If your existing interior or exterior plaster is starting to show signs of needing to be refreshed or the painting never seems to last, then it’s probably time to have your plaster renewed to breathe in a new lease of life to your decorating efforts.

So if you’re giving wall plastering a thought, there’s a need to have a rough estimate of the cost a professional is likely to charge so you can set a budget and start planning. However a direct answer can not be provided for this question as there are so many factors that a professional will put into considering before coming up with a quote that’s unique to your specific requirements.

A lot of plasterers will come up with a quote for the job using the number of square metres of wall space that’s going to be covered. This is due to the number of plasterboards as well as the other materials that the plasterer will need to purchase, how long the work will take and also the labour that’ll be involved in completing the project.

Another popular influencing factor that several plasterers use is the size of the room to be plastered. This is the main reason why you’re more likely to find the prices in small, medium as well as large rooms. Therefore, in order to have a more accurate estimate of the cost of your plastering project, you’d have to call in a qualified professional to have a look at the job at hand. Generally, to re-plaster a small room will cost within the range of £350 to £550, a medium room will cost within the range of £400 to £600 and a large room, between £550 to £700.