Find a Plasterer you can trust in Barnetby.

Can You Plaster Over WallPaper?

If you have wallpaper installed on your wall surface and you’re considering plastering the wall, when you put into consideration the stress involved in removing a wallpaper you may want to consider plastering directly over the wallpaper. This is quite understandable as removing a wallpaper can be quite time consuming and tedious, but plastering directly over wallpaper is a mistake that should never be made. Plastering over wallpaper is in no way a viable option due to the fact that it can only turn out disastrous after a couple of weeks or even days in some cases as the plaster will crack and crumble. As a result, you’ll have to firstly scrape off the wallpaper in order to assist the plaster get to be firmly secured to the wall behind.

When you plaster over a wallpaper, this will make the wallpaper wet and it’ll absorb the moisture. And once the plaster does not have moisture, the only result is for it to crack and start to crumble. Hence, plaster and wallpaper is never a good combination.

Asides from cracking and crumbling, anther issue is that the wallpaper will bubble. You can actually key the wallpaper with the help of a knife and it might look secured for some time, however it’ll eventually crumble and you’d have to scrape off the plaster complete to start all over again. The wallpaper will bubble as the plaster can’t be keyed into a wallpaper and the wallpaper will only work as a barrier between the plaster and the wall.

Overall, plaster always needs to slowly dry off as well as a good and proper surface to grip to. No matter the amount of PVA mix you spread on the wallpaper, it will always remain a barrier. So you’d have to remove the wallpaper completely to get a great result.

Artex simply refers to a surface coating that’s commonly incorporated for interior decorating. Although it’s usually found on ceilings but it can also be used on the walls as well. The surface coating enables the professional plasterer or decorator add both texture as well as patterns to it. Originally, the name “Artex is the trademark of a UK based company known as Artex Ltd. Over time, the Artex name has been used to refer to all textured coatings, although there are other businesses that manufacture and sell identical products.

You can find Artex on ceilings as well as walls of mainly residential properties. In the 70’s and 80’s, it was pretty much a trend to have either your wall or ceiling ( can be both ) covered with Artex. The surface coating can be incorporated to create raised, textured swirls as well as patterns on ceiling and walls. There are a number of different patterns that can be made using Artex and some of these includes the following: Broken leather, swirl, stipple, fan or shell as well as knifed plaster. It can also provide just a bobbly raised uneven patter appearance from top to bottom.

Artex is main put to use by mainly decorators ( mostly plasterers). This is a skilled job as it’s tedious to create uninformed patterns especially if you don’t know how or where to start. Although the skill of Artex is very much a trade that’s dying rapidly now, but it was pretty much in high demand especially in the 70’s and 80’s. Nowadays, homeowners now prefer smooth plastered finishes over Artex, as they can be easily painted or wallpapered.

Also commonly referred to as drywall, plasterboard is an incredibly versatile product which features a sandwich of gypsum plaster between thick paper layers. It’s mainly used on both walls and ceilings due to the wide range of benefits it provides. Not only can plasterboard be made to be humidity resistant, fire resistant as well as noise resistant, but they’re also known to have a low environment impact, easy to repair and can be used to conceal stuff from plain sight. As a result of these benefits couple with the fact that they also happen to be quite affordable, plasterboard has grown to become a ubiquitous phenomenon in modern residential buildings.

When it comes to the installation of plasterboard on ceilings, one of the major sources of concern for several homeowners is the determination of the thickness required to ensure a durable and long-lasting project. If you’re planning to fit plasterboard on your ceiling and wondering the thickness that’ll be appropriate, then you’ve come to the right place. In this post, we’re going to give you a good insight on what plasterboard to use for ceilings. Let’s take a look!

First and foremost, the standard plasterboard sheet size is 120 cm in width and within the range of 180 cm to 360 cm in height. These sizes are designed to provide the much-needed support to the standard stud spacing which is 160 cm. Depending on the manufacturer, plasterboard can be in four different widths. Now talking about the thickness, there are two standard thicknesses of plasterboard - 9.5 mm and 12.5 mm. The sizes of plasterboard for ceilings are 9.5 mm or 10 mm. Most individuals tend to assume that the thicker the plasterboard the better, but this is absolutely false. A thicker plasterboard will only stick harder to the ceiling which will make it hard to seal joints if required.

Artex is a type of interior surface coating, similar to plaster. It’s used to create decorative textured finishes on ceilings and walls, so it takes longer to dry than plaster.

Artex is actually a brand name, but it’s used to refer to similar products made by other manufacturers too. It was particularly popular in the 1970s, but is still used to create attractive wall and ceiling finishes today.

What Is Plaster Made Of?

Plaster is one of the most commonly used materials when it comes to building construction. It’s a crucial component that’s incorporated in coating walls, ceilings as well as partitions and it hardens on drying. Plastering is one of the most ancient building materials which has taken over mud to plaster reed or sapling huts so as to serve as a protection against the elements. Here, we’re going to take a look at the multiple compositions of plaster. These components are very important due to the fact that they form a protective coating on whatever they are used on. They work to protect surfaces such as ceiling and underlying walls from scratches or any form of damage.

Plaster comprises a few materials which includes gypsum, lime or cement and all operates in a similar way. Gypsum is made of calcium sulfate dihydrate and it’s the main component of main forms of plaster, sidewalk chalk, blackboard, drywall and more. Meanwhile, lime plaster is made up of sand, water and lime ( mostly non hydraulic hydrated lime). And lastly, cement which is a mix of suitable plaster, portland cement, sand as well as water.

The plaster is usually produced as a dry powder which is mixed thoroughly with water to create a stiff but also a paste that’s workable immediately before it’s applied to the wall or ceiling.

It’s quite easy to confuse a drywall with a plaster but there are some differences. Not only is plaster a much older style of wall construction than dry wall, but it’s also a lot more expensive than installing a drywall. Plaster walls are also able to provide you with a more durable finish when compared to a drywall and it makes for a better quality finish.

Artexing a ceiling can be a tricky job, but whether you’re considering hiring a professional or DIY, it’s helpful to know how it’s done.

Artex is available either in a paste or powder form. The paste is ideal if you’re making small repairs or additions to an existing ceiling. But, if you have a whole ceiling to cover, the powder is more cost effective. When you’re ready to get started, you’ll need to mix the powder up with cold water according to the instructions.

It’s possible to artex over plaster, plasterboard or paint. If you have a plasterboard surface, you should tape and fill any joints or cracks before you begin. Plaster and plasterboard both require a coat of sealant or primer first. You can usually artex straight over paint, but any gloss paint should be sanded down, and any dark paints covered with a layer of white.

Artexing can get quite messy, so make sure you empty the room you’re working in as much as possible, lay down sheets and wear protective clothing and glasses. You might want to practice on a piece of board before you start on the ceiling.

Start by using a brush or roller to cover a 500 square cm area with a generous layer of artex. Then use a brush, comb or roller to create your chosen texture. Every time you do a new section of ceiling, try to blend it with the other sections you’ve done. Don’t be tempted to cover the whole ceiling before you start adding texture – the artex will dry too quickly for you to do it all in time.

Artex usually needs 12-24 hours in a well-ventilated space to dry completely.

Artex is a water based surface coating which is used to decorate both ceilings and walls with a textured finish. Back in the 1970’s, artex happens to be very popular when the swirling or spiky effects it creates  were considered to be the best of fashion when it comes to interior designs. However, in today’s world, an artex ceiling is not only considered outdated but also a pain to clean and repair.

If you have an artex ceiling in your residential property and looking for a way to get it off, then you’ve come to the right place. In this post, we’re going to show you how its done without much stress.

To get started you’d need to get the following tools and material which includes: safety goggles, dust mask and rubber gloves, plastic sheeting, canvas drop cloth ( carpet) or rosin paper (hard floor) and step ladder

Prepare the room. Start this by moving all furniture out of the room or stack the furniture at the centre of the room and cover using plastic sheets. Once done, cover all non-removable items with plastic sheets and lay down a canvas drop cloth for carpet floors and rosin paper for hard floors

• Put on your safety gear
• Use a utility knife or joint knife to slowly chip away at the texture and create a smooth surface.
• Mix joint compound in a bucket as per the instructions on the package
• Skim the surface with a thin layer of joint compound to smooth it out using a taping knife, then leave to dry overnight before you proceed
• Lightly sand the surface smooth with the help of a 220-grit sanding block
• Use a damp cloth to wipe the surface clean prior to painting.

Artex is a water based decorative surface coating is typically incorporated on both walls and ceilings so as to apply a pattern. During the peak of its popularity in the 1970’s, it was considered the height of fashion when it comes to interior wall designs however its major drawback remains the fact that it usually contains asbestos especially if it was manufactured before the laws governing the use of asbestos was changed in the year 2000. And asbestos, as we know it, can be deadly when disturbed and its fibres are inhaled.

If you have artex installed in your purchased property and you do not know when the artex walls were done, or perhaps you just want to change the aesthetic design of your home into something more modern and to your personal taste, then you may want to remove the existing artex from your property for good. If this is your wish then you’ve come to the right place.

To remove artex from your walls you can choose to do so using the steaming method or through the use of an external product.

Using the steaming method, you should know that it’ll be more labour intensive and time consuming. You need a lot of patience moving your steamer slow and steady because if left on a spot for too long can damage the wall behind the coating. Once the artex has been dampened with the steamer, you can then scrape them off with a handheld scraper.

A faster solution would be to use an external product to remove your artex.  For example, you can use X-Tex which is a water-based coating remover. All you need to do is paint the substance over your artex wall and leave to dry for about 30 to 60 minutes before peeling away the artex.