Find a Plasterer you can trust in Amlwch.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

✓ Firstly, you need to put the plasterboard sheet flat on a firm surface.

✓ Use the tape measurement to measure the cut you wish to make.

✓ With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

✓ Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

✓ Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

✓ The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

✓ Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

✓ Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

✓ Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

Also referred to as drywall, plasterboard is a panel that features an inner layer of gypsum and spread between facer as well as backer paper. It is mostly incorporated in the construction of both interior walls and ceilings. Plasterboard can be made to be humidity resistant, fire resistant as well as noise resistant. Due to these reasons and also the fact that it’s very easy to install and very affordable, plasterboard is a very popular choice when it comes to interior walls and ceilings.

One of the major issues that most homeowners face when fitting plasterboard is the thickness required to make the project a long lasting one. But not to worry, we got you covered! If you’re about to install plasterboard for your ceiling and wondering the thickness that’ll be appropriate, then you’ve come to the right place. In general, the standard plasterboard sheet size is 120 cm in width and within the range of 180 cm to 360 cm in height. These sizes are designed to provide the much needed support to the standard stud spacing which is 160 cm. Depending on the manufacturer, plasterboard can be in four different widths.

Now talking about the thickness, there are two standard thicknesses of plasterboard - 9.5 mm and 12.5 mm. The sizes of plasterboard for ceilings are 9.5 mm or 10 mm. Most individuals tend to assume that the thicker the plasterboard the better, but this is absolutely false. A thicker plasterboard will only stick harder to the ceiling which will make it hard to seal joints if required.

Plasterboards are a great noise insulators which can also reduce disturbances from other activities. As a result, for walls, size of plasterboards that’s considered appropriate for walls is 12.5 mm or 13 mm.

Artex was originally made using white asbestos to make it stronger. However, this stopped in the mid-1980s, and the use of asbestos was banned in the UK in 1999, due to its extreme health risks. So, any artex you buy today won’t contain asbestos.

If you have an artex ceiling or wall that was created before 1999, it may have asbestos in it. This won’t be a health hazard if you leave it undisturbed, so it’s not necessary to remove it. However, if you want to get rid of or alter your artex ceiling or wall, you must get it tested to check if it has asbestos in or not first. If it does, you’ll need to hire a qualified professional to work on it.

If you’re looking to plaster your ceiling, one of the most essential parts of the process is cutting the plasterboard. Once you’re able to master this skill, the rest of the plastering is quite easy. This is a task that can be done by any competent DIYer but with a little bit of patience and confidence. If you lack any of these attributes, we’d strongly recommend you call in a reliable professional who can guarantee the best results for help. In this guide, we’re going to take you through the plasterboard ceiling cutting process. Let’s take a look!

To cut plasterboard ceiling, you don’t need any expensive tool which is usually not the case when it comes to carpentry. If you won’t be cutting a lot of plasterboard, all you really need would be just an old handsaw or plasterboard one, a Stanley knife as well as a straight edge. However, if you’ll be cutting lots of plasterboards, you’ll require the following to make your task a lot easier:

✓ An old handsaw

✓ A Stanley knife and many spare blades

✓ A straight edge like a long spirit level

✓ A surform

✓ A battery drill and oh2 screwdriver bits, with specific plasterboard screws.

To cut plasterboard to length, you’ll have to first score a line on the face side of the board with a straight edge and Stanley knife. Once done, simply lift the sheet off the ground and snap it along the score line. Then, you can run your knife down the other side of the board , cutting the back of the plasterboard backing sheet. Upon completion, your plasterboard is now ready to be fitted on your ceiling.

Artex is a water based surface coating which is used to decorate both ceilings and walls with a textured finish. Back in the 1970’s, artex happens to be very popular when the swirling or spiky effects it creates  were considered to be the best of fashion when it comes to interior designs. However, in today’s world, an artex ceiling is not only considered outdated but also a pain to clean and repair.

If you have an artex ceiling in your residential property and looking for a way to get it off, then you’ve come to the right place. In this post, we’re going to show you how its done without much stress.

To get started you’d need to get the following tools and material which includes: safety goggles, dust mask and rubber gloves, plastic sheeting, canvas drop cloth ( carpet) or rosin paper (hard floor) and step ladder

Prepare the room. Start this by moving all furniture out of the room or stack the furniture at the centre of the room and cover using plastic sheets. Once done, cover all non-removable items with plastic sheets and lay down a canvas drop cloth for carpet floors and rosin paper for hard floors

• Put on your safety gear
• Use a utility knife or joint knife to slowly chip away at the texture and create a smooth surface.
• Mix joint compound in a bucket as per the instructions on the package
• Skim the surface with a thin layer of joint compound to smooth it out using a taping knife, then leave to dry overnight before you proceed
• Lightly sand the surface smooth with the help of a 220-grit sanding block
• Use a damp cloth to wipe the surface clean prior to painting.

Plastering is suitable to cover most Artex. If it’s shallow Artex, it may be covered by skimming plaster on top. If the pattern of the Artex is too deep, you may need to use plasterboard to cover it or if you want to remove it entirely, you will need to use a wallpaper steamer.

Plastering will fix small cracks in walls. Very small cracks may be fixed by simply reskimming plaster. More serious cracks will usually mean that you need to use new plasterboard or backing plaster. Larger jobs or deep cracks may need an experienced plasterer to come in.

Artexing a ceiling can be a tricky job, but whether you’re considering hiring a professional or DIY, it’s helpful to know how it’s done.

Artex is available either in a paste or powder form. The paste is ideal if you’re making small repairs or additions to an existing ceiling. But, if you have a whole ceiling to cover, the powder is more cost effective. When you’re ready to get started, you’ll need to mix the powder up with cold water according to the instructions.

It’s possible to artex over plaster, plasterboard or paint. If you have a plasterboard surface, you should tape and fill any joints or cracks before you begin. Plaster and plasterboard both require a coat of sealant or primer first. You can usually artex straight over paint, but any gloss paint should be sanded down, and any dark paints covered with a layer of white.

Artexing can get quite messy, so make sure you empty the room you’re working in as much as possible, lay down sheets and wear protective clothing and glasses. You might want to practice on a piece of board before you start on the ceiling.

Start by using a brush or roller to cover a 500 square cm area with a generous layer of artex. Then use a brush, comb or roller to create your chosen texture. Every time you do a new section of ceiling, try to blend it with the other sections you’ve done. Don’t be tempted to cover the whole ceiling before you start adding texture – the artex will dry too quickly for you to do it all in time.

Artex usually needs 12-24 hours in a well-ventilated space to dry completely.