Find a Driveway Installer you can trust in Hamilton.

Do you want to install a new patio? If yes, then on top of the agenda will definitely be the cost of paving slabs. However providing a single and accurate estimate to the cost of your new patio is almost impossible as there are many factors that can influence what the price would be. These factors include the size of the area, the choice of stone, installations and lots more.

To get a more accurate estimate of your cost there’s is the need to look at some factors before calculation. These includes envisioning your patio as well as putting the drainage in mind. Firstly, you’ll need to decide where you want your patio to be - this should include considering whether you’ll get enough privacy sitting on your patio and more. If you’re able to identify where to put your patio, you’ll be able to have a clearer idea of the potential shape and size of the patio. Secondly, there’s a need to consider the drainage because failure to provide adequate drainage will only result in storing of water which leads to a development of algae or vegetation across your patio.

The material you opt for is also a huge determinant of your patio’s cost. When it comes to paving slabs you’ll only get what you pay for. Deciding to go for cheaper paving slabs will most likely lead to frequent staining, slippery surface, tough maintenance as well as constant cracking. Consequently, the act of cutting back on the cost of paving slabs will only you cost you more money in the long run. What’s more? If you have an existing patio you’d like to replace, then you’d probably need to include the cost of removing the existing one.

1. Prepare the base If you want your resin bound driveway to last a long time, you need to ensure that you prepare the base properly. Remove any block paving, grass or soil and dig down until you hit solid ground. Lay a sub-base of asphalt for good permeability. If you’re laying over the top of your current driveway, make sure that all cracks are increased into a ‘v’ shape with a saw and ensure the surface is dry and weed-free.
2. Mix the resin You must follow the instructions on the materials you have to the letter if you want the curing process to work. Usually batches come in ‘Part A’ and ‘Part B’. Keep the resin container secure and on a protective surface to avoid splashing, then mix Part A for 10-20 seconds at a slow speed with a helical bladed mixer. Add Part B and mix thoroughly at a slow speed for about 2 minutes until it’s blended together.
3. Mix the dried aggregates and sand with the resin Place a quarter of the aggregates into a mixer, then add the pre-mixed resin and start a stopwatch. You should then add the rest of the aggregates before slowly adding the sand. When you’re happy with that mix, stop the stopwatch. That time is the time that you need to spend mixing any other resin and aggregates to avoid colour variation.
4. Lay the mix on the surface Transfer the mix to the work area then plan a laying route. When the mix is laid out, use a very clean trowel to spread the mix. Clean it regularly during the process to avoid dragging aggregates out of place. Once the aggregates stop moving in a fluid movement and become solid, stop trowelling. Then you can polish the surface to give it an attractive shine.

From gravel and crushed stones to asphalt and tarmac, the choice when it comes to surfacing options for driveways is truly staggering. However, what’s not too clear is the options that best suits a sloping driveway. If you also possess a sloping driveway and wondering the best material to install, you’re definitely not alone. This is a major source of concern for several home and property owners in the UK being fully aware that making the wrong choice here can prove really costly and disastrous. In order to help you make the best informed decision possible, we’ve put together this post which takes a look at the various driveway material options available to you.

• Gravel
  This driveway surfacing option provides a truly enjoyable “crunch sound when driven on, however, the satisfaction will be short lived if installed on a sloped driveway. If installed on a sloped driveway, there’s going to be a continual displacement as instinctively rolls downhill on an incline.

• Concrete
  This can prove to be a great problem if installed on an incline. This is due to the fact that concrete is subject to freeze/thaw phenomenon which makes it steep and slippery lacking the needed traction.

• Tarmac
  This is particularly far from ideal when it comes to a steep driveway surface. This is because it requires continuous maintenance to prevent spillages from spoiling the surface.

• Resin
  The best surface for a steep driveway is simply that made from resin. This is due to the fact that this surfacing option allows water to soak away naturally. They’re perfectly permeable, preventing water from pooling and reducing the risk of falls.

While many professionals will recommend a pressure washer to clean block paving, it’s possible to clean your paving without one – just scrub the affected areas with a firm bristled brush and use plenty of soap. Then, rinse off the area with clean water.

Gravel is the cheapest driveway surfacing material. Asphalt costs a little more than gravel, and concrete is significantly more expensive. The cost of paving depends on the material you use. Obtain as many quotes as possible as materials and costs differ from company to company.

The best way to clean resin bound driveways is to sweep it regularly with a stiff broom. This will remove any debris and prevent moss from growing. It's a good idea to jet wash it after sweeping, because this will get rid of any smaller parts that a broom might not collect.

When you jet wash or power wash your resin bound driveway, make sure the pressure isn’t too high. It’s recommended to keep the pressure less than 150bar, as anything too strong could damage the surface. Make sure the water is cool, but not cold – both hot and cold water can damage the resin. Make sure the jet wash nozzle is at least 20cm from the surface. Any closer and this could damage your driveway. Use a sweeping back and forth motion to clean.

If you treat the area before you have your resin bound driveway installed, you shouldn’t get any weed growth. But if you get any moss or algae appear, you can apply a moss and algae killer that should remove and prevent any regrowth. If you have ingrained algae, you can remove it with a strong bleach solution; make sure you follow the manufacturer’s instructions. This should also help restore the driveway’s original colour. Make sure you rinse your driveway thoroughly with clean water after using bleach on it to prevent any harm to wildlife or plants.

If you get chewing gum on your resin bound driveway and you can’t get it off with a pressure washer, try using a freezing spray on it first. Then use a wall scraper to gently remove it – never dig under the chewing gum as this could damage the resin on your driveway.

Clearing snow from a gravel driveway can be tricky – you need to remove the snow without taking the gravel with it.

If the snow’s quite light and dry, try using a leaf blower. You might find that this is enough to get the snow out the way. If it isn’t, start by using a shovel. Use this to clear the top layer of snow off your driveway, leaving about an inch behind. Then, use a rake to remove most of the remaining snow. This won’t take away 100% of the snow or leave all of your gravel in place, but it’s still pretty effective. You can then lay salt to melt away the rest of the snow and stop it turning into ice.

Are you worried there’s a slope on the area where your block paving is to be installed? Good news is, it’s very possible to lay block paving on a slope. However, this can be a very difficult task which should be done by a reliable professional ( especially if you lack proper training and experience) who can guarantee the best results, the first time and also help save you money from possible costly mistakes. This guide will provide you with everything you need about the slope block paving installation process. Let’s have a look!

• Demarcate The Walkway

To get started, you have to determine how and where you want your walkway to be while also determining the thickness of the paver. Ensure to choose the less sloppy area and utilize landscape paint to mark the area visibly.

• Prepare The Ground

Clear out all forms of dirts, roots, rocks and other debris on the soil. Once done, proceed to cutting the sods to the required length and put them somewhere close.

• Make Boundaries

There’s a need for landscape borders. Here, it’ll be easier to use plastics as boundaries for your lawn’s edges. Install them on the sides that have already been cut

• Apply A Level Of Gravel

Obtain the correct size of gravel and spread them evenly over the area to ensure a firm foundation for the pavers is formed. Makes sure that the rocks is at a minimum of 2 inches deep into the soil.

• Install The Block Pavers

Start from the centremost position of the pathway and work towards the sides until you’re able to cover every inch of the area.

• Apply A Layer Of Cement

Apply cement over the pavers and utilize a broom to sweep it and fill up all the gaps and spaces between the pavers. Then, press the pathway to be levelled using a compactor.