Find a Driveway Installer you can trust in Dunbar.

To inexperienced people laying of paving slab isn’t much more than digging a little, purchasing little amount of mortar and pressing down the paving slabs. But how good would it have been if only it were that easy in real life? The truth is, in reality, laying paving slabs does not only require you to prepare your sub-base painstakingly and mix your mortar using the appropriate materials, but you’d also have to work with accurate and precise paver placements to guarantee the patio’s longevity. As a result, if you lack proper training or experience, we’d recommend you hire the services of a seasoned professional who can guarantee the best results and also save you time and extra cash that may result from possible costly errors. In this guide, you’d gain more insight into the paving slabs laying process.

To get started, you’ll need sharp sand, cement, shovel, wheelbarrow, pointing trowel, rubber mallet, spirit level, jointing compound, hard-bristled brush and tarpaulin.

• Mix a layer of mortar for each paver.

• Apply the mixed mortar onto the sub base by using the trowel.

• Slot the first flag in place and ensure not to stain the paver’s surface with the mixed mortar.

• Using a rubber mallet, carefully tap the paver to the mortar bed. Once done, ensure the surface is even with a spirit level.

• Take a measurement of the gap between the pavers

• Repeat the above steps until all pavers have been perfectly laid

• Leave the pavers to dry for about 1 to 2 days. You can protect it using a tarpaulin if concerned about rain.

• Use the jointing compound to fill up the paver gaps to bind together the pavers. Ensure to wipe off any excess compound using the hard bristled brush.

Creating a tarmac path or driveway is a tricky process. It’s a job best left to professionals who know what they’re doing, as there are plenty of opportunities for it go wrong. However, even if you’re planning to hire someone to do it for you, it’s worth knowing how it’s done.

Firstly, you’ll need to remove any existing path or driveway and excavate down to formation level – about 175mm below paving level. Then, a membrane is laid down to prevent weed growth.

Next, a sub-base goes down, usually made of crushed rock or concrete. This is compacted and the tarmac is laid over the top. This is put down in two layers, and is rolled to make it compact and smooth.

It’s important to use edging when laying tarmac, to ensure that it doesn’t run off where you want your path or driveway to be. Tarmac paving and driveways also needs suitable drainage.

Do you know why paving slaps is a popular choice for both driveways and patios? Well, it’s the versatility! With its durability, diverse colour range, different styles as well as a timeless appeal, paving slabs happen to be a common choice amongst home owners. However, you should know that redeeming these benefits is not as simple as shovelling mortar and pressing down the paving slabs, and neither is it a case whereby you can just copy the laying process of a porcelain paving or block paving. Laying of paving slabs is on a whole other level! As a result, we’d recommend employing a trustworthy professional who can guarantee the best results the first time, especially if you lack proper training or experience to complete the task. In this step by step guide, you’ll discover more about the paving slabs laying process.

• Prepare your paving foundation. This includes checking that your foundation is level, marking out the area to be paved with wooden pegs, removing all vegetation and top soil to a depth of about 200mm to 250mm and raking the area level to ensure and even depth.

• Mix a layer of mortar for each paver and apply the mixed mortar onto the sub base by using the trowel.

• Lay the slabs on top of the laying course at the lowest point of the area to be paved.

• Take note that you may need to cut some slabs depending on the paving area size, your chosen slabs and the pattern selected.

• Once done, brush the area clean and start jointing. The best way to do this is by applying kiln dried sand to the paved area and carefully brush into the joints with a brush.

• Push the sands into the joints using a plate compactor

• Check the paved area for any gaps and fill where necessary.

Are you having weed problems on your carefully picked out block pavings? After spending huge bucks to install the block pavings, the last thing any homeowner would want to discover is weed taking over the prized asset. Fortunately, this is a problem that can be effectively handled in a few simple steps provided in this article.

Basically, sealing of block paving is all about prevention of weed growth in the area by total weed removal, putting of sand between the block paving joints and sealing with a good quality sealant. This is a task that’s best left for a reliable professional to guarantee the best results especially if you lack proper training and experience. This guide will give a good insight into the process.

Here are the equipment you’ll need to get started: pressure washer, weed killer, bin bag, broom, small brush, protective gear, sealing roller, spueegee, jointing sand and sealer and DIY sprayer.

lRemove The Weed

• Put on a protective clothing and gloves

• Get a weed disposal bag to clean while you go.

• Apply the selected weed killer on both areas where weeds are present and the absent ones to prevent any growing.

lPressure Washing

• Angle your pressure washer between the gaps. This is done to remove all weeds and debris that are still lying around as well as removing all possible chemical residues to create a thorough clean between the paving slab.

• Leave the washed area to dry.

l Sand The Joints

• Check the weather forecast to ensure there’s about 24 to 48 hours of dryness as its important for both sand and sealant to do a perfect job.

• Put sand between the gaps and push it down with your small brush until its levelled.

lSeal The Gaps

• The sealing process should be done immediately and sanding.

• Clean up the patio

• Perform a test using a small area

• Apply the sealant

• Apply the second of sealant

• Leave to dry for about 2 to 3 hours.

Moss growth on tarmac and asphalt is pretty common. This can make your driveway or outside area slippy and untidy, so it’s a good idea to get rid of it.

Start by using a stiff brush to dislodge as much moss as possible and clear it off your driveway. Then use a moss killer to kill any remaining moss. Make sure you follow the product instructions – some moss killers are best used on tarmac or asphalt that’s clean and damp, whilst others are better for dry surfaces.

To prevent further moss growth, it’s a good idea to reduce the amount of shade on your tarmac or asphalt as much as possible. This will help you keep it as warm and dry as possible, and reduce moss growth.

Gravel driveways, when properly installed, can be a very cost effective way of surfacing all driveways including both the big and the small ones. As a result, it has grown to become a common choice amongst homeowners in the UK. It does a great job at giving a property a more natural look than other driveway surfacing options which includes concrete, block paving or tarmac.

Are you planning to install a gravel on your driveway? If yes, then you’ll most likely be interested to know exactly how much it’s going to cost. Well, to get started you’ll have to decide whether you’ll be doing this yourself or perhaps you’d be hiring a specialist. The project could be much more effective if you decide to tackle it on your own as you’re only going to be worried about the paying for the materials without any labour costs. However, installing a driveway is in no way an easy task even for the competent and more experienced DIYers. So if you choose to carry out the project on your own, you should also get ready for a longer completion time than it would have been if you hired a tradesman which is usually around 48 hours. If you have all the tools and materials in place before commencement, then it’s possible to complete the project over the weekend. However, there are many risks involved such as the possibility of misjudging the amount of base layer and gravel required etc.

Here, we’ll look at the various material costs of gravel driveways, as labour costs largely varies from one tradesman to the other.

The material cost of a gravel driveway of about 20 square metre should range between £1100 to £1200, 40 square metre should cost between £1600 to £2000 and 80 square metre gravel driveway should cost between £2800 to £3200.

From concrete paving to material bound and also obstruct paving, there are a plethora of hard surfacing system alternatives readily available on the market today. Nevertheless, one of the alternatives that really stands out is the Indian stone appearing. The Indian stone is not just distinguished for its variety colour profiles and also reduced maintenance requirements, however its additionally understood to be really budget friendly when contrasted to various other comparable high-end appearing alternatives like Yorkshire paving. The Indian stone paving is always among the very best when it comes some top qualities such as strength, resistance, structural in addition to its visual benefits. In this post, we'll be checking out a lot of reasons that you need to consider getting an Indian stone paving mounted on your driveway. Let's have a look!

• Visually appealing. If the look of your driveway is just one of your top concerns after that you'll hardly get many better choices than Indian stone paving. This kind of difficult emerging comes with a wide range of stunning colours you can choose from to make your landscape appear like heaven in the world.
• Little maintenance. Indian stone driveway calls for just a marginal maintenance as most of the dirt built up over time will be gotten rid of by water, while you can easily pipe down the few continuing to be ones. It's truly that simple!
• It's durable as well as safe. As a result of the high percentage of quartz, the Indian stone paving is very durable. It makes an exemplary material that can hold up against all type of pressure. Not only is it resistant to weather extremes, however it additionally won't get harmed because of lots of foot or cars and truck traffic.
• Inexpensive. As a result of its many benefits, it might actually look like an unique material, however you will not have to break the bank to install it.

There’s no doubt that weeds coming through your block paving can be unsightly and annoying. But, it’s relatively easy to get rid of weeds that are growing in the joints between your block paving. To start, pull out the larger weeds, and then you can use a pressure washer or firm bristled brush to remove the smaller weeds and debris from the joints in your block paving. It’s best to then refill the joints with additional sand to ensure your block paving remains level. Regularly brushing your block paving and treating with weed killer will help to prevent the weeds from reoccurring.