Find a Driveway Installer you can trust in Bude.

There are several effective ways to clean paving slabs. It’s important to pick a method that suits you and your paving material.

Whatever method you use, start by removing all weeds and loose debris from your paving. Then, if you have a pressure washer, you can simply use this to clean away any dirt.

If you don’t have a pressure washer, you can try using soapy water or watered-down bleach. If you use soapy water, mix a mild detergent like washing up liquid with warm water. Then pour it onto your paving, work it in with a brush and rinse it off with clean water.

If you use bleach, first make sure that the water won’t drain off onto any plant life, as this can kill it. You should also avoid using bleach on concrete slabs, as it will cause them to fade. Mix one-part bleach with five-parts water, pour it onto your paving and work it in with a brush. Then leave it for 15 minutes and rinse it off with clean water.

If you want to give your concrete paving slabs a new lease of life, it’s possible to paint them. This is a great option if your slabs are looking tired or you want a new look, but you don’t want to invest in new paving.

Before you go ahead, you need to make sure that your slab paving is clean and dry. And if it’s been sealed, you’ll need to strip this off. Make sure you get a paint that’s specifically designed for the job so you get the best results.

So have you decided to lay block paving on your property? If yes, then knowing how much it would cost would help you prepare a budget and set out a plan before commencement of the project. The cost of block paving depends on a wide range of factors such as the the size of the area in question, cost of labour as well as the type of brick and block paving to be used. So how much does block paving cost? In this article, we’ll give you an general idea of the cost of laying of block paving on a driveway so you can estimate your cost according to your personal requirements and needs.

For a small to medium sized driveway featuring a complex design, the block pavings’ cost starts from a range between £3,000 to £4,000, meanwhile that of a large sized pathway will jump to a range between £6,500 to £7,500. And depending on the complexity of the design, the final cost of the project can be greatly impacted as it would also take a longer period of time to be completed. For the same small to medium sized pathway featuring a simple design which usually takes up to 3 to 4 days will cost within a range of £4,500 to £5,500. While a complex design such as a herringbone pattern will take up to 5 to 6 days and costing within a range of £5,000 to £6,000.

Furthermore, there are also other factors that can determine the price of block paving and another example is the current condition. This includes the preparation work to be carried out before laying the block paving can be a time consuming task especially when the driveway is in a terrible condition and this comes with a high labour cost. Another factor to be considered is the materials used in making the block paving such as stone, concrete, cement, composite and resin - they’re all available in various range of colours and textures. They play a key role in the block paving cost.

Oil stains on your concrete driveway can look obvious and unsightly. However, there are several different ways to remove them.

If you’ve only just spilled the oil, you can use a mixture of absorbent material, like sawdust, and solvent, like acetone or lacquer. Combine these, place them on the stain, cover and leave for about 24 hours. Then sweep up the mixture and rinse the area with water.

If you’ve got a small, older stain, you can use a detergent like baking soda, vinegar, washing up liquid or laundry detergent. Cover the stain with the detergent and leave for about 30 minutes. Then, add hot water and scrub the area and rinse. You might need to repeat this if necessary.

If it’s a larger, more stubborn stain, you might need to use a special degreaser. You can use this similarly to a detergent but make sure you follow the instruction on the bottle carefully.

The best way to clean resin bound driveways is to sweep it regularly with a stiff broom. This will remove any debris and prevent moss from growing. It's a good idea to jet wash it after sweeping, because this will get rid of any smaller parts that a broom might not collect.

When you jet wash or power wash your resin bound driveway, make sure the pressure isn’t too high. It’s recommended to keep the pressure less than 150bar, as anything too strong could damage the surface. Make sure the water is cool, but not cold – both hot and cold water can damage the resin. Make sure the jet wash nozzle is at least 20cm from the surface. Any closer and this could damage your driveway. Use a sweeping back and forth motion to clean.

If you treat the area before you have your resin bound driveway installed, you shouldn’t get any weed growth. But if you get any moss or algae appear, you can apply a moss and algae killer that should remove and prevent any regrowth. If you have ingrained algae, you can remove it with a strong bleach solution; make sure you follow the manufacturer’s instructions. This should also help restore the driveway’s original colour. Make sure you rinse your driveway thoroughly with clean water after using bleach on it to prevent any harm to wildlife or plants.

If you get chewing gum on your resin bound driveway and you can’t get it off with a pressure washer, try using a freezing spray on it first. Then use a wall scraper to gently remove it – never dig under the chewing gum as this could damage the resin on your driveway.

Patios do not require lots of maintenance. They will only need occasional cleaning to make sure that the material keeps its original appearance. It's always best to clean your patio with a pressure washer and occasionally tap each slab or brick just to check the sand underneath hasn't washed away.

It’s always a good idea to be sure of how you’re going to keep the annoying gravel spillage off your driveway way before its installation, however, if you’ve already done so, it’s better late than never. We all know how great a gravel driveway can look when the gravels manage to stay in place. When gravel is used on a driveway it provides a great transition from the normal hardness of a driveway to the organic softness of the lawn which doesn’t retain water or gush runoff during irrigation or rainfall. Unfortunately, the sad thing here is gravel don’t just like to stay put. Before long, if ignored, you’d realize your hard surfaces will almost be covered with gravel coming in from the side. So what’s the solution to this rather annoying situation?

Here, we’ll show you just how you can keep your gravel in place in your driveway. Let’s take a look!

The solution here is simple - simply make use of Pour On. With Pour On, you won’t have to think about of clearing out your gravel features to put an end to the issue of loose rocks spilling on your hard surfaces. With Pour On, you’ll be able to hold your gravel in place for several years to come. And even more importantly, it’s able to achieve this objective while also protecting the integrity the existing permeability of your driveway. What’s more? It also goes a long way to retain the natural look provided by your gravel driveway which makes it the perfect solution to the annoying gravel spillage issues.

Cleaning block paving is a fairly straightforward task, although you’ll want to be careful to not use any chemicals that may cause damage to the surface. Use a simple household soap, mixed with water, and brush this across the paving with a stiff brush. Then, simply rinse off with clean water. Alternatively, use a pressure washer – but be careful not to use it on a powerful setting, as this may damage the joints and can cause slabs to come loose. Using the pressure washer on a medium setting and at a 45 degree angle is recommended.