Find a Driveway Installer you can trust in Banchory.

The best way to clean resin bound driveways is to sweep it regularly with a stiff broom. This will remove any debris and prevent moss from growing. It's a good idea to jet wash it after sweeping, because this will get rid of any smaller parts that a broom might not collect.

When you jet wash or power wash your resin bound driveway, make sure the pressure isn’t too high. It’s recommended to keep the pressure less than 150bar, as anything too strong could damage the surface. Make sure the water is cool, but not cold – both hot and cold water can damage the resin. Make sure the jet wash nozzle is at least 20cm from the surface. Any closer and this could damage your driveway. Use a sweeping back and forth motion to clean.

If you treat the area before you have your resin bound driveway installed, you shouldn’t get any weed growth. But if you get any moss or algae appear, you can apply a moss and algae killer that should remove and prevent any regrowth. If you have ingrained algae, you can remove it with a strong bleach solution; make sure you follow the manufacturer’s instructions. This should also help restore the driveway’s original colour. Make sure you rinse your driveway thoroughly with clean water after using bleach on it to prevent any harm to wildlife or plants.

If you get chewing gum on your resin bound driveway and you can’t get it off with a pressure washer, try using a freezing spray on it first. Then use a wall scraper to gently remove it – never dig under the chewing gum as this could damage the resin on your driveway.

Slab paving is a great material to use to create a sturdy shed base.

Start by measuring out the area where your shed is going to be. This needs to be the size of your shed, plus about 10-20cm extra each way. Mark it out with string and pegs, make sure it’s square, and dig it down to about 6cm deep.

Then create a sand and cement mixture and put a layer down, followed by your paving slabs. Make sure you start in one corner and use a rubber mallet and spirit level to make sure they’re as level as possible. Leave this to set and you’re ready to use your shed base.

• Where you live
• How big you want your driveway to be
• What colour or design you would like
• Whether any additional work will need to be completed to prepare the area for the driveway

Do you want to install a new patio? If yes, then on top of the agenda will definitely be the cost of paving slabs. However providing a single and accurate estimate to the cost of your new patio is almost impossible as there are many factors that can influence what the price would be. These factors include the size of the area, the choice of stone, installations and lots more.

To get a more accurate estimate of your cost there’s is the need to look at some factors before calculation. These includes envisioning your patio as well as putting the drainage in mind. Firstly, you’ll need to decide where you want your patio to be - this should include considering whether you’ll get enough privacy sitting on your patio and more. If you’re able to identify where to put your patio, you’ll be able to have a clearer idea of the potential shape and size of the patio. Secondly, there’s a need to consider the drainage because failure to provide adequate drainage will only result in storing of water which leads to a development of algae or vegetation across your patio.

The material you opt for is also a huge determinant of your patio’s cost. When it comes to paving slabs you’ll only get what you pay for. Deciding to go for cheaper paving slabs will most likely lead to frequent staining, slippery surface, tough maintenance as well as constant cracking. Consequently, the act of cutting back on the cost of paving slabs will only you cost you more money in the long run. What’s more? If you have an existing patio you’d like to replace, then you’d probably need to include the cost of removing the existing one.

When your driveway is suffering from depression, it becomes unsafe for driving (a danger zone) and ugly - no homeowner wants that! Unfortunately, most driveways won’t hold flat for long as they tend to develop cracks and potholes pretty quickly. Here, we are going to take you through how to fill asphalt driveways’ depression so as to ensure the sinkholes in your driveway poses no threat to you or your loved ones, while also beautifying your property. The approach to be used depends on the intensity of the depression. If its only a few cracks and holes, this can easily be repaired with some equipment. But if otherwise is the case, then calling a reliable professional will be your best bet. In this article, we’ll show you how to repair dips in your asphalt driveway relatively quickly.

✓ Pick a date with warm and sunny weather. This is because if you work in a cold weather, chances are the materials will freeze and hence, unusable. So find a day when the temperature will over 50 degrees Fahrenheit and below 80 degrees Celsius and when there would be no rain. We’ll advise a day between May to October.

✓ Prepare the area. Remove all loose stones, soil, dirt as well as vegetation from the holes. Once done, you can then proceed to washing the area with a pressure washer or sweep with a broom.

✓ Apply a thin mixture of asphalt to the area. Use a flat stirring stick to coat the low driveway area with a thin mixture of asphalt.

✓ Tamp the asphalt repair mix. Purchase the right kind of asphalt to repair the driveway. Fine aggregate asphalt mixture is more suited to filling small holes, whereas the coarse aggregate is more suited to filling larger holes. Apply layers ( about 2 inches each time) of the asphalt repair mix to the sunken area and use a shovel to give it a smooth finish. Once done, simply make the area smooth and protect it with a piece of plywood. Do not walk or drive on the area for a couple of days.

Creating a tarmac path or driveway is a tricky process. It’s a job best left to professionals who know what they’re doing, as there are plenty of opportunities for it go wrong. However, even if you’re planning to hire someone to do it for you, it’s worth knowing how it’s done.

Firstly, you’ll need to remove any existing path or driveway and excavate down to formation level – about 175mm below paving level. Then, a membrane is laid down to prevent weed growth.

Next, a sub-base goes down, usually made of crushed rock or concrete. This is compacted and the tarmac is laid over the top. This is put down in two layers, and is rolled to make it compact and smooth.

It’s important to use edging when laying tarmac, to ensure that it doesn’t run off where you want your path or driveway to be. Tarmac paving and driveways also needs suitable drainage.

Driveways usually sink because they haven’t been laid properly. They may not have been dug deep enough, or the installer might not have used the right materials. This will need to be corrected at the earliest opportunity, although in extreme cases, the driveway may need to be completly be relaid.