Find a Landscaper you can trust in Shrewsbury.

1. Remove any existing fascia boards Remove the fascia boards and the old felt if you’re re-felting.
2. Measure the shed roof Measure the roof, taking into account that you should leave around 50mm for overlaps at the eaves and 75mm at the gable ends. You’ll probably need 3 pieces of felt, but some smaller sheds only need 2.
3. Apply felt to the roof Once you’ve cut the felt to size, apply the each piece to the roof, pulling it tight. Then nail along the length of the roof at 100mm intervals. For nails at the bottom edge, they can be wider – around 300mm. If you’re adding a piece of felt in the middle of the shed along the apex, fix it using adhesive, then nail it at the lower edge at 50mm intervals.
4. Tidy up the overhangs Fold down the felt at each overhang and nail it securely. Cut a slit in the overhang at the apex using a pen knife, then fold that down and nail at 100mm intervals along the gable. If you like, you can add fascia boards to keep the shed looking neat. Use wood nails to secure them and then trim away any excess felt.

• The shed doesn’t cover more than 50% of the garden
• It’s not in front of your house
• The shed is single-storey with eaves no higher than 2.5m and the overall height is no taller than 4m for a dual-pitched roof, or 3m for any other type. If it’s located within 2 metres of your property’s boundary, it mustn't be more than 2.5m high
• There’s no veranda or balcony
• The floor area is no bigger than 15m² - up to 30m² may be covered under Permitted Development if other conditions are met
• The shed is for domestic use only by those who live in the property and there’s no sleeping accommodation – that means you can’t run a business from the shed unless you apply for planning permission

• If you live in a listed building, you’ll need Listed Building Consent before you can build a shed in your garden
• If you live in a conservation area or similar, the maximum area of ground covered by outbuildings, pools and enclosures situated more than 20m from any wall of the house mustn’t exceed 10m² if they’re to be considered as a permitted development
• If you own a piece of woodland, you must seek planning permission for any permanent structure
• In Scotland, you’ll need planning permission if any part of the shed comes within 1m of a neighbouring property or is more than 2.5m high
• In Northern Ireland, there are rules about how close your shed can be from a road that passes by the back of your house. It’s best to check for clarification

1. Place a post in the corner of the frame you created with the pegs and string. Measure and mark out 100mm from each side.
2. Dig out this soil to a depth of 700mm (watch out for cables or pipes). You should have a 300 x 300mm hole. Repeat for the other 3 corners.
3. Using a brick bolster, split a concrete block in two. Put a section of the block in each hole.
4. Get a length of post longer than you need and place one in each hole. You can cut it down later.
5. Create props on each post to hold them in place until you’re ready to add a cement mix. Check that they’re level. When you’re happy that they are, secure them in place with a concrete mix, making sure you create a slope in the concrete so that rainwater runs away from each post. When the concrete is set, remove the props.
6. Create a string line around each corner post and find the centre point between each. Place a timber batten at each point, ensuring that they’re not spaced any more than 1500mm apart.

1. Working from the corner where the deck will be at its highest above ground level, measure and mark on the post where the highest part of the frame will be.
2. Measure from the far side of one post to the opposite and cut sections of joist to size. Line up a piece of joist with the mark you made and temporarily secure it. Factor in a 2mm fall for every metre of decking so rainwater can run off.
3. Secure the frame to the other corner post, ensuring it’s at the right level. Do this for every side of the outer frame.
4. Using 100mm coach screws with washers hanging on the end, secure each end of the four sections of frame.
5. Mark out where the centre of the support posts will be and secure all of these posts to the frame, except the centre post.
6. Add your central support joists. These should run in the same direction as the deck boards will run. You’ll need to measure from the inside of the frame on one side to the inside of the frame on the opposite side. Attach the joist in the same way as you did for the other posts. Repeat so the centre post is in between two sections of frame and secure the posts with concrete.
7. Trim down all the posts to the correct height using a saw.
8. Add your weed-control fabric and weigh down with gravel across the entire area.

1. Measure 400mm from the centre of the outer frame and mark a line. This will be where the first joist is positioned. Repeat at 400mm intervals down the length of the frame – if the last one will be more than 400mm, add another joist to create enough support.
2. Attach a joist hanger to each end of the joist.
3. Place the joist in position so the centre lines up with the 400mm spacer mark.
4. Secure using external grade screws once you’re happy that the joist is flush with the frame.

Moss, mushrooms and weeds are all problems that many homeowners face on their lawns. Luckily, with a bit of maintenance, there are ways you can get rid of these unwanted organisms and prevent them from coming back. Getting rid of moss A simple way to remove moss from your lawn is by scarification. This basically means that you vigorously rake your lawn, but only do this in the autumn when the grass is actively growing and it’s not too hot, cold or dry. However, you can also use specific weedkillers to control moss on your lawn, and most of these should be applied when the moss is actively growing. Apply in fine weather by hand or with a push-along spreader, making sure not to apply too much as you could kill off the grass too. Check the instructions, as some will require watering after 48 hours if it’s not rained. Then, get into a scarification routine to help prevent moss growth. Removing mushrooms from your lawn If you’ve got mushrooms in your lawn, it usually means that your lawn is damp and shaded, so it never dries out, and is organic waste-rich. There could be a drainage problem with your lawn that is encouraging mushroom growth, so it’s important to investigate why the mushrooms are growing to prevent them from returning once you’ve removed them. To get rid of mushrooms in your lawn, make sure you scarify your lawn and get rid of all the moss, thatch and dead grass that comes up. If you leave it, this is heaven for mushrooms to grow in. If your lawn is shaded, try to prune and thin surrounding trees to offer it more light. If you do all of these things, it will prevent mushrooms from growing in the future, and then it might be worth using a fungicide to get rid of the mushrooms that are there. But if you just do this step, it’s likely the mushrooms will just come back. How to get rid of weeds To get rid of weeds from your lawn, you can use selective weedkillers that will just kill the weeds and leave your grass alone. But if you’d rather not use weedkiller, you can get rid of weeds from your lawn manually. For large, deep-rooted weeds like dandelions or plantains, use a trowel to lever them out, ensuring that you get the whole plant including its roots. Then use compost to fill the hole it leaves behind, pushing it deeply into the hole. Sprinkle with fresh grass seed, cover with extra compost and water. Make sure you keep the area damp until the seed has germinated. To prevent moss, mushrooms or weeds from returning, the best things to do are:

• Scarify your lawn in the autumn, and lightly in the spring if necessary
• Seed your lawn in the autumn if you need to
• Try to keep trees trimmed and pruned as much as possible to reduce shade
• Use a pre-emergent weedkiller in the spring to catch them before they grow and handpick any that come through
• Mow your lawn regularly in the spring and summer, being careful not to remove more than a third of grass at a time, then before winter give it one last mow and a fertilisation treatment

Pitting, also referred to as spalling is the event whereby “pits” or small holes start showing on the surface of your concrete driveway which makes it appear both worn and uneven. Concrete driveway pitting is a common but highly frustrating problem for most homeowners. You’ll see some concrete driveways that’ll only start to pit after a couple of years, but this is not true for all concrete driveways as others will start to show signs only after a couple of months. So how do you tackle this issue? Well, it’s relatively simple to tackle, however if you’re not confident or lack the necessary skills, we’d recommend you get in touch with a reliable professional who can guarantee the best results for help. In this guide, we’ll take you through the concrete driveway pitting repair process.

✓ Prepare the pits by cleaning the area, clearing out all debris and more. The small pits can be cleaned with a stiff brush while a sturdy broom will do a good job for larger pits.

✓ Make use of a hose to spray the concrete pits and flush out all remaining bits of waste.

✓ If you’re tackling series of small pits, simply use a caulking gun filled with pre-mixed epoxy and specially formulated for concrete to fill the pits. Clear off the excess eproxy ensuring that its level with the concrete surface. Once done, simply leave for at least 24 hours before the application of a concrete sealant to prevent the wear and tear of the new concrete.

✓ Chisel out a little concrete and clean with a pressure washer. Once done, apply a concrete resurfacing compound mixture into the holes and use a trowel to level off.

✓ Ensure that the repaired concrete driveway is protected from rain and foot traffic for at least 6 hours (or 24 hours for vehicles).

There are several reasons why you may wish to plant a garden. To have a healthier environment, eat healthier, cook with fresh produce and lots more. Regardless of your purpose, one challenge faced by several home and property owners is exactly how to go about this and where to get started. If you’re having the same issues, then you’ve come to the right place. In this post, we’re going to take you through the process involved in planting a garden to ensure your project turns out a success. If you lack the confidence required to pull this off, we’d highly recommend you call in a professional who can guarantee the best results.

1. Start small. Being overly ambitious when planting a garden could be easiest way to a disastrous outcome. Give yourself a realistic goal and learn to plant healthy and productive plants by starting small.
2. Identify your site. To ensure a great garden, the plants need lots of sunlight. So, you can go for a space that gets about 6 to 8 hours of sunlight on a daily basis. Also, make sure that there’s a water source nearby to make it easy to give your plants water as required.
3. Choose you garden type. Decide how your garden will grow, be it in raised beds, in ground, in containers or a combination of styles. This will ensure that your garden is neat and orderly while also enhancing its curb appeal.
4. Make a list. Create a list of the plants you’d love to have in your garden.
5. Plan your planting. This involves spacing your plants as they’re going to grow bigger, deciding which plant goes where and identifying the best soil to grow them.
6. Get your plants.
7. Plant them.

1. Plan your shed base You must have a sturdy base for your shed, otherwise the frame won’t stand properly and could stop the door from opening. Decide whether you’re going to have:
   • A concrete base laid on hardcore
   • Concrete slabs on sharp sand
   • Treated wood beams on hardcore or shingle
   • An interlocking plastic system
   All bases should be laid on firm, level ground as far as possible.
2. Treat wood with preservative To help your shed last as long as possible, you should coat all the wooden parts with timber preservative before you put it together.
3. Put the shed floor together Some will need more assembly than others, but you need to make sure that the floor panel is attached to the joists; follow the manufacturer’s instructions for the correct spacing.
4. Put up the shed walls
   • Mark the centre point of each wall on its bottom edge, then do the same for the shed floor so you can line them up together.
   • Stand the gable end on the base and line it up. Check that it’s vertical with a spirit level – you might need someone to support the panel while you do this. Use a temporary holding batten to keep it in place.
   • Fix a side panel to the gable end panel with countersunk screws, then add the second side panel in the same way.
   Don’t attach the panels to the floor until you’ve fitted your shed roof.
5. Fit the roof
   • If the shed comes with a support bar, put this in position before you put the roof panels in.
   • Nail the roof panels in place, ensuring there’s a parallel and equal overlap at each end.
   • Roll out some roofing felt from front to back, leaving a 50mm overlap at each side. Secure it with clout-headed felt tacks at 100mm intervals.
   • Apply mastic sealant to the outside corners, then fix each corner trim with 30mm nails.
   • Add the fascias and finials, predrilling 2mm holes to avoid splitting the wood. Nail them through the felt into the shed using 40mm nails.
6. Add the shed windows
   • Slide each windowsill into the tongue and groove cut out, then put the window cover strip in position, fixing it to the vertical framing.
   • From inside the shed, put the glazing sheets into the window rebates, making sure the bottom edge of the glazing sheets sit on the outside of the sill.
   • Fix the window beading on the top and sides with 25mm nails.
7. Fix the walls to the floor Before you do anything, make sure you check that the centre marks on the walls line up with the marks on the shed floor. Then fix the wall panels to the floor with 50mm screws, aligning them with the joists.
And that’s it! But if you’re not confident in building a shed yourself, there are plenty of professionals available who will be happy to help.

Overseeding your lawn is an essential part of keeping your lawn looking its best. It’s also known as reseeding, and helps to repair damaged areas that might have been caused by a harsh summer or winter. It’s best to overseed your lawn during the spring or autumn, when the temperature is mild but there’s still a fair amount of rainy days to help the grass seed grow. To prepare your lawn for overseeding, you should do the following things around 1-2 weeks beforehand:

• Weed the lawn by hand or using a weedkiller (make sure you leave enough time to do this according to the instructions)
• Remove stones and large twigs
• Scarify your lawn to remove moss and loosen soil
• Fertilise the soil with a quick-release fertiliser

Once you’ve taken these steps, you’re ready to start overseeding your lawn.

1. Mow your lawn to around 25mm in length.
2. Water the soil so it’s moist but not too damp.
3. Sprinkle your new grass seed evenly over the lawn, but apply more in patchy or thin areas. Generally gardeners say to use 35g per square metre, but up to 50g on thin areas.

When you’re finished, give your lawn a final water, and do this every day until the new grass is established – particularly if it’s not rained. Just make sure you don’t overwater it. It’s also a good idea not to walk on your lawn for around 2-3 weeks after you’ve overseeded it.