Find a Landscaper you can trust in Llandrindod Wells.

1. If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
2. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
3. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
4. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
5. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

How To Draw A Garden Landscaping Plan

Are you thinking about constructing a new garden landscape? Do you have an existing one but forgot where you planted those tulip bulbs the previous autumn? Or perhaps you’re just trying to identify the exact spot where you cut back that clump of wilted foxglove, without mistakenly digging it up. For everything to be much easier when it comes to a garden landscape, it’s always a wise decision to draw a garden landscaping plan.

To get started, let’s take a look at the materials you’ll need to acquire. These includes a piece of white paper on which the existing elements on your garden will be plotted, a piece of tracing paper and tape to give options for planned additions, a pencil, an eraser as well as a measuring tape.

For more accuracy while drawing your plan, you’ll need to measure the garden’s distances, perimeter, the existing garden beds size as well as the trees’ and shrubs’ shape and size.

• Write down the measurements taken on the scrap paper.

• Assuming it’s a medium sized backyard garden that’s 18 feet wide, we allocated a scale of 3 feet to equal an inch.

• Using a piece of white paper (could be graph if you wish) and a pencil, carefully outline the perimeter of the space. Once done, you can then sketch in the existing plants as well as other special features on the space (features that are of a permanent nature like trees, fences and paths).

• Hold a piece of tracing paper and tape in on top. Then you can sketch out the plants you wish to add to fill in the spaces in the garden on the tracing paper.

Laying artificial grass on concrete needs a slightly different approach to if you’re installing it over soil. The good news is that it’s much less labour intensive, as you don’t need to do any digging or levelling.

Ideally, your concrete base should be in good condition, and have an adequate fall on it to provide efficient drainage. If it doesn’t, you might have to do some repair work or drill some drainage holes first.

When you’re ready to start, begin by cleaning your concrete base. Use a jet wash or a hose and brush to dislodge and disperse any dirt or plant growth. Once it’s clean, leave it to dry completely.

Then, you need to fit an underlay - usually it’s made of foam. This will provide padding to make your artificial grass softer and more comfortable to walk on. It will also help to level out any slopes on uneven parts on the concrete. Make sure it’s a good-quality underlay that’s permeable – if it’s not, you could end up with damp artificial grass and nasty smells as it will hold moisture. Roll out the underlay and cut it to shape, taping any separate sections together.

Next, use an adhesive to secure the underlay to your concrete. Make sure you leave gaps in the adhesive to allow water to drain off easily. Leave the glue to dry, then you can start laying your grass.

Roll out your grass like you did with your underlay, cutting it to shape and joining any separate sections together with artificial grass tape. Then glue the grass to the underlay. Leave it dry, give the grass a brush, and it’ll be ready to use!

Laying artificial grass is a popular project – it’s a great way to create a smart, low-maintenance garden. There are plenty of professionals around who are experts at installing artificial grass, but it’s possible to DIY too if you’re feeling confident.

Lots of homeowners choose to replace their existing turf with artificial grass, so lay it on soil. To do this, start by clearing the area of any greenery or turf. Then remove any extra soil to a depth of about 40mm. You might want to leave the centre of your area slightly higher than the edges for a more natural look.

Next, you need to add a weed membrane and a sharp sand sub-base. It doesn’t really matter which one of these you do first, but you might find it easier to lay the weed membrane first and then use the sand to weigh it down, to a depth of about 35mm. Use a rake and plank to make the sand level, and compact it with a plank and heavy hammer. It doesn’t need to be completely flat – gentle slopes are fine. The weed membrane should overlap joints by 300mm.

After you’ve done this, you can lay your grass. Roll it out, trim it to size and fasten it in place. Make sure the ends of the grass rolls are staggered so they don’t end in a line. Lay the artificial grass with the pile (the strands) leaning towards the house so it looks nice and full when you’re looking out from the house. If you’ve decided to use edging boards, you can nail the grass into the tops of the boards. Or, if you haven’t, use ground pins to anchor it into the soil. Brush the grass and you’re done!

• Have a step tread width of 900mm – if you don’t want them that wide, they should be no less than 760mm
• Add a central step riser to stairs wider than 900mm to prevent them buckling
• Add a step depth (the vertical distance between each step) of between 150 and 180mm if building your own riser, so the steps are at a comfortable depth

• Step treads (the actual step themselves)
• Step risers
• Coach screws
• Deck screws
• Saw
• Drill

1. Make sure the ground where you want to put your steps is level and firm. If it’s not, consider laying concrete or paving slabs to provide a secure surface for your steps to sit so they don’t sink.
2. Grab some joist off-cuts and cut them to the same width as your step treads. Attach them to the step risers at the top and bottom using countersunk coach screws.
3. Place the steps against the sub-frame of the deck; if you’ve put slabs down for support, make sure the steps sit in the middle of them. The longest edge of the stair riser should be on the slabs, and the short edge against the deck. Drill pilot holes through the step and sub-frame joist, then screw the step to the sub-frame with more coach screws.
4. After drilling pilot holes, screw the treads into the risers at each end with deck screws.
5. If you don’t want gaps between each stair, you can add joist off-cuts or deck boards. Measure the height and depth of the gap, then screw the off-cut or board into the step riser with two screws at each end.

1. How to build a shed base out of paving slabs
   • Mix sand and cement together to make mortar or use a pre-mixed one
   • Use a trowel to lay mortar for 1 slab at a time on the sub-base and lift a damp-sided slab onto the mortar, using a piece of timber and club hammer to tap the slab into position carefully. Continue to lay the first row of slabs
   • Make equally-sized spacers in all the joints in the slabs to ensure they’re the same size, checking it’s level as you go along
   • Next lay slabs along the two adjacent outer edges, filling in the central area row by row
   • Leave the mortar to set according to the instructions or for at least 48 hours before filling in the joints with mortar or paving grout
2. Building a shed base from concrete
   • Create a wooden frame around your shed base area (also called formwork) to stop the concrete from spreading
   • Mix pre-mixed concrete with water or use 1 part cement to 5 parts ballast
   • Wet the sub-base using a watering can with a rose on the end
   • Pour the concrete onto the framed base starting in one corner
   • Push the blade of a shovel up and down in the edges of the concrete to get rid of air bubbles
   • Use a rake to spread the concrete, leaving it around 18mm higher than the top of the frame. Work in sections of around 1-1.m²
   • Compact the concrete using a straight piece of timber that’s longer than the width of the base. Move the timber along the site, hitting it along at about half of its thickness at a time until the surface is evenly ridged
   • Remove excess concrete and level the surface by sliding the timber back and forwards from the edge that you started. Fill in any depressions and repeat until even
   • Run an edging trowel along the frame to round off exposed edges of the concrete and prevent chipping
   • Cover the concrete with a plastic sheet raised on wooden supports to allow slow drying. Weigh it down with bricks
   • Once the concrete is set, you can install your shed and remove the wooden frame with a crowbar

When it comes to fence ownership and responsibility, this is often a subject of dispute between neighbours and understandably so. Owning a fence comes with a number of responsibilities such as arranging and paying for the maintenance and more. Therefore, if you’re not yet sure who owns the garden fence, then you’d probably want to have that sorted to make sure your property stays protected at all times. In this post, we’re going to give you an insight into some of the rules guiding fence ownership in order to help you make informed decisions. Let’s take a look!

There’s no rule of thumb on whether you own the fence on the right hand or the left hand side of your property. Therefore, if you’ve heard any “rules that states otherwise, you can fling that out the window because not everyone will own the left hand side to their fence. The first way to determine who owns the garden fence or which side of the fence you’re responsible for is simply by looking. Although this is not guaranteed or a definite way to determine ownership, it can go a long way to give you a good idea. As you would have expected, fences are most likely built on the land that belongs to the boundary’s owner with the further edge of the fence making the actual boundary. As a result, you can determine a fence ownership simply by identifying where the frames are.

Also, you can determine fence ownership using the title deeds for an official and accurate answer. A copy should be given alongside your paperwork which is received when purchasing your house.

1. Unroll your two pieces of artificial grass, ensuring that the pile is running in the same direction. Fold over each piece by about 300m.
2. To get the perfect seam, cut at least 3 tufts back, ensuring that you don’t trim any grass blades.
3. Either remove the backing on your self-adhesive tape and unroll it down the centre of the join, or roll it out ensuring that the shiny side is down then fix at either end with adhesive.
4. Fold over the grass onto the tape and bring each piece together, ensuring there’s a 2-3mm gap at the seam.
5. Where the pile runs over the edge of the seam, fold over the artificial grass.
6. Apply a small amount of adhesive under the edge of the first section of grass with a mastic gun, then add some to the front edge to stick the second piece.
7. Bring the seam together, ensuring that you don’t get any grass blades stuck. Place a plank with some heavy objects on over the join to ensure that it dries securely.