Find a Landscaper you can trust in Ashford.

1. How to build a shed base out of paving slabs
   • Mix sand and cement together to make mortar or use a pre-mixed one
   • Use a trowel to lay mortar for 1 slab at a time on the sub-base and lift a damp-sided slab onto the mortar, using a piece of timber and club hammer to tap the slab into position carefully. Continue to lay the first row of slabs
   • Make equally-sized spacers in all the joints in the slabs to ensure they’re the same size, checking it’s level as you go along
   • Next lay slabs along the two adjacent outer edges, filling in the central area row by row
   • Leave the mortar to set according to the instructions or for at least 48 hours before filling in the joints with mortar or paving grout
2. Building a shed base from concrete
   • Create a wooden frame around your shed base area (also called formwork) to stop the concrete from spreading
   • Mix pre-mixed concrete with water or use 1 part cement to 5 parts ballast
   • Wet the sub-base using a watering can with a rose on the end
   • Pour the concrete onto the framed base starting in one corner
   • Push the blade of a shovel up and down in the edges of the concrete to get rid of air bubbles
   • Use a rake to spread the concrete, leaving it around 18mm higher than the top of the frame. Work in sections of around 1-1.m²
   • Compact the concrete using a straight piece of timber that’s longer than the width of the base. Move the timber along the site, hitting it along at about half of its thickness at a time until the surface is evenly ridged
   • Remove excess concrete and level the surface by sliding the timber back and forwards from the edge that you started. Fill in any depressions and repeat until even
   • Run an edging trowel along the frame to round off exposed edges of the concrete and prevent chipping
   • Cover the concrete with a plastic sheet raised on wooden supports to allow slow drying. Weigh it down with bricks
   • Once the concrete is set, you can install your shed and remove the wooden frame with a crowbar

There are a number of reasons why disputes can arise between neighbours – all of which can be quite frustrating and challenging. In some cases, this can even cause serious friction and lead to an all-out war. When it comes to the topic of fencing, one of the most common questions that arises is whether or not you can attach something to your neighbour’s fence. If you’re having the same concern, then you’ve come to the right place. In this post, we’re going to give you a good insight into this to help you make informed decisions moving forward. Let’s take a look!

The short and simple answer to this question is no, you can’t attach anything to your neighbour’s fence. If your neighbour owns the fence and you’ve not obtained any permission to do so, then you’re not allowed to attach anything to the fence. Otherwise, you can get into serious trouble with your neighbour as well as the law. If you want to attach something or have the wall on your side painted using another colour, then there’s the need to get a permission from the owner. And while doing so, make sure you’re provided with a written permission so as to avoid problems later in the future.

Another question that mostly arises is what if your neighbour declines your request, is there anything you can do about it? Well, the answer to this is no, there’s nothing you can do about it unless you’re able to convince your neighbour otherwise. And you should know starting a neighbour war or being spiteful can only make matters worse for you.

1. Place a post in the corner of the frame you created with the pegs and string. Measure and mark out 100mm from each side.
2. Dig out this soil to a depth of 700mm (watch out for cables or pipes). You should have a 300 x 300mm hole. Repeat for the other 3 corners.
3. Using a brick bolster, split a concrete block in two. Put a section of the block in each hole.
4. Get a length of post longer than you need and place one in each hole. You can cut it down later.
5. Create props on each post to hold them in place until you’re ready to add a cement mix. Check that they’re level. When you’re happy that they are, secure them in place with a concrete mix, making sure you create a slope in the concrete so that rainwater runs away from each post. When the concrete is set, remove the props.
6. Create a string line around each corner post and find the centre point between each. Place a timber batten at each point, ensuring that they’re not spaced any more than 1500mm apart.

1. Working from the corner where the deck will be at its highest above ground level, measure and mark on the post where the highest part of the frame will be.
2. Measure from the far side of one post to the opposite and cut sections of joist to size. Line up a piece of joist with the mark you made and temporarily secure it. Factor in a 2mm fall for every metre of decking so rainwater can run off.
3. Secure the frame to the other corner post, ensuring it’s at the right level. Do this for every side of the outer frame.
4. Using 100mm coach screws with washers hanging on the end, secure each end of the four sections of frame.
5. Mark out where the centre of the support posts will be and secure all of these posts to the frame, except the centre post.
6. Add your central support joists. These should run in the same direction as the deck boards will run. You’ll need to measure from the inside of the frame on one side to the inside of the frame on the opposite side. Attach the joist in the same way as you did for the other posts. Repeat so the centre post is in between two sections of frame and secure the posts with concrete.
7. Trim down all the posts to the correct height using a saw.
8. Add your weed-control fabric and weigh down with gravel across the entire area.

1. Measure 400mm from the centre of the outer frame and mark a line. This will be where the first joist is positioned. Repeat at 400mm intervals down the length of the frame – if the last one will be more than 400mm, add another joist to create enough support.
2. Attach a joist hanger to each end of the joist.
3. Place the joist in position so the centre lines up with the 400mm spacer mark.
4. Secure using external grade screws once you’re happy that the joist is flush with the frame.

Different types of gardening work will need to be carried out at different times of the year. Garden maintenance is a year round job, although the amount of work will usually decrease during the winter. For larger landscaping projects, aim to have these done through autumn, winter and early spring, to give plants time to get established before summer. Be aware that poor weather over winter can slow down the work.

A patio is an outdoor space which can be used for a variety of stuffs which includes fun time with family and friends, reading time or just relaxing as the fresh breeze blows. With all these benefits and more, it’s becomes more obvious that there’s a need to keep your patio in a tip top condition at all times. If otherwise, you may not be able to enjoy your patio to your satisfaction and probably, for as long as you would want. You simply have to provide it with a regular maintenance which involves inspecting and identifying the damages that needs to be repaired before it gets out of hand. Fortunately, the minor repairs can be done by yourself if you’re confident enough. However, for bigger damages it’s advisable to call in a professional for help. In this article, we’ll take you through the patio reparation process.

✓ Prepare the area. This involves removing the problem piece gently and carefully. If there’s a piece you think can still be useful, store it in the re-use pile or you can start a new one. Once you’re done removing the pieces, the next thing to do would be to start removing anything that’s unwanted from the damaged area like debris, unwanted soil etc, and start sand fitting with some fresh sand. This should be levelled out to ensure there’s no bumps.

✓ With the sand down, you can start by putting the pieces back in together. This should be done gently to avoid any further damage. Do this until your patio

✓

Scarification is the name given to the process where you remove excess thatch and moss from your lawn to encourage it to grow and look healthy. Although it sounds difficult, it’s actually pretty easy – simply grab a sturdy rake and apply moderate pressure to rake out moss, thatch and dead grass. Then collect it up and add to your compost heap if you have one. You can also use a petrol or electric rake, but you just want to tease out the moss and thatch. Don’t be tempted to go deep into the grass, as this could damage your lawn. So when should you scarify your lawn? The experts say that the best time is in the autumn, when the grass is actively growing and it’s not too hot, cold or dry. Most of summer’s weed seeds will have gone, so you won’t encourage weeds to grow in the raked-up soil. This soil also makes an ideal seed bed for over seeding with new grass seed, so that’s why you don’t want to get weeds in there as well. However, you may also carry out light scarification in the spring – usually around April. Make sure you don’t go too far though – as you will end up with a rather disfigured lawn if you scarify too heavily and the dryness of summer stops the lawn from recovering. It’s also best to scarify your lawn in the spring if the following apply:

• If you couldn’t do it the previous autumn – if you keep putting it off, you might end up with extreme moss and weed growth
• If your lawn is shaded – these areas will thin over winter and start to thicken from spring onwards, so if you scarify in the autumn you’ll make your lawn even thinner.
• If your lawn is under trees – pair the shade from the trees with the fall of leaves in the autumn and your grass won’t be healthy, but in the spring the trees are bare, allowing lots of light onto your lawn to help it grow.

1. Mark out the area and dig the top layer of soil, trying to get the ground as flat as possible.
2. Build a timber frame to size.
3. Measure out 4 rows of 3 blocks to create good weight distribution and lay in place.
4. Underneath each block, dig around 50mm wider than the blocks and about 150mm deep. Fill the hole with pea gravel until it’s flat.
5. Place timber planks along the rows of blocks and see how level it is. Add or remove blocks where necessary. If it’s only a small difference, use shingle underneath the timber until it’s level.
6. Nail your timber shed base to the timber planks to create a sturdy base for your shed.