Find a Landscaper you can trust in Tain.

Laying a lawn is a task that’s best left to the professionals especially if you don’t know what you’re doing. However, if you can follow a simple logical process, you’ll save yourself a lot of headache – simply start from the edge and work inwards. If you’re looking to lay your lawn by yourself, then you’ve come to the right place! In this post, we’re going to consider the processes involved in lawn installation in order to ensure your project turns out a success. Let’s take a look!

Firstly, the tools you’re going to need to lay your lawn includes the following – sturdy boots, gardening gloves (should be thick), wheel barrow, garden fork or rotovator, landscaping rake, laying boards, knife or edge trimmer, hosepipe and broom.

1. Start from the outside edge. Install the initial strips horizontally overlapping the boundary a bit (trim the back once done). Press down carefully to make sure there’s a good contact with the soil (make sure not to squash the lawn).
2. Proceed to lay the adjacent pieces till the first row of the lawn along the entire edge is completed.
3. Continue with the next row. If there’s a need to stand on the laid turf, simply make use of a plank so as to avoid squashing or denting the turf. It’s important to ensure the successive rows are staggered to prevent the short edges from lining up.
4. Proceed by butting and pushing the edges to create a tight joint (make sure the turf is not stretched).
5. Use a wood saw or sharp serrated knife to trim any untidy edges. Remember to make use of a plank to ensure you do not walk directly on the turf.
6. Water the newly installed turf adequately to ensure the water penetrates the soil. However, do not turn it into a mud bath.

• Tongue and groove timber boards
• Boards for the ledges and braces, at least 20mm thick
• Nails
• Hammer
• Saws, including a circular saw
• Chisel
• Mallet

1. Cut your boards to size If you can’t buy boards at the right height and width for your door, cut the boards to length using a circular saw. Don’t forget to sand and treat any cut ends with timber preservative. Lay out the boards in the best arrangement for your shed door, with the inside of the door facing up.
2. Arrange the ledges and braces On most shed doors, you’ll probably need 3 boards across the back of the door to form the ledges. The ledges keep the door straight and keep the boards of the door together. The braces are the parts of the door that slope down to form a ‘Z’ shape between the ledges. Ensure that the braces are sloped up from the bottom and middle hinge to stop the door from sagging as the timber expands and contracts in the weather. Once you’re happy with the arrangement, mark the spots on the boards where they will meet and cut out of the housings using a chisel and mallet.
3. Put the door together Use clamps to pull the boards together and hold the ledges and braces in place. Nail from the front of the door through the boards and ledges to fix them. Secure the ledges and braces with screws; you may want to pre-drill and countersink holes to prevent the wood from splitting. Remember to treat them with preservative if you do.
4. Fix the shed door hinges Make sure you measure carefully before attaching the hinges, ensuring you know where the pin sits in relation to where the door opens.
5. Treat the door and add locks and handles Apply some wood oil, like linseed or teak oil, to help prevent water damage. Then add locks or handles to your shed to help keep it secure.
If you’d rather leave it to the professionals, there are plenty of specialists that will be able to make a shed door for you, or even put up an entire shed.

When it comes to landscaping issues, lawn mushrooms are a very common occurrence. If you’re one of the several home and property owners who simply loves to have a great looking grass, finding mushrooms in your lawn can be a truly frustrating experience. However, with the right skills and knowledge the problem of mushroom growing in lawns can be resolved. If you don’t have the confidence required to carry out this task, then we’d recommend you call in a professional landscaper for help in order to avoid costly errors and unnecessary expenses. In this post, we’re going to put you through the processes involved in lawn mushroom removal.

First and foremost, let’s consider why mushrooms grow on lawns. To determine why mushrooms are growing on your lawn, simply examine the state of your lawn. Lawn mushrooms thrive in damp, shaded and organic waste rich environments. Figure out if you have drainage problems with supports the mushroom challenge, organic waste to be removed or perhaps you have areas on your yard that happens to be very shady.

In order to get rid of mushroom in your lawn, you’ll have to resolve your yard problems. If your lawn is very wet, try to find out if there are things you can do to minimize the moisture. You can reduce the decaying organic materials in your yard by raking your grass clippings, replacing existing mulch or detaching your lawn. If your yard happens to be quite shady, check if some targeted pruning can help to enable the access of more light to your yard. Also, you can apply a fungicide to eliminate the existing lawn mushrooms.

As a home or property owner, you’re generally allowed to build next to your neighbour’s fence as long as it’s on your own side of the property. With that in mind, there are certain laws that regulate how close a fence can be built to buildings on the same lot or neighbouring lots. In addition, there are also local bylaws that provide limitations on the placements as well as height of fences so as to address safety hazards. In this post, we’re going to give you a good insight into how close you can build to your neighbour. Let’s take a look!

In general, if the fence is in your boundary then you’re allowed to build a 2-metre high brick or wooden fence or wall. However, this may differ depending on your location in the UK. As a result, you may want to reach out to your municipality’s building department in order to determine what these rules and limitations are in your area. In the events whereby there are no such restrictions but you’re still concerned, you can try informing your neighbour what your concerns are. However, if they’re not receptive there are some steps you can take to ensure your plans go as smoothly as possible. These steps include the following:

• Ensure to leave sufficient space for both the posts and footings
• Stagger your fence posts in order to make sure you’re not digging your neighbour’s
• Consider using concrete posts as they’re much stronger and will last a lot longer
• Use kickers or plinths for raised gardens and flower beds
• Make use of concrete plinths as they won’t rot over time like a wooden fence.

Properly erected fences shouldn’t require a great deal of maintenance. Any rotting boards can usually be replaced without replacing the whole panel. Timber fencing should be stained every 2-3 years. General maintenance is something you can carry out yourself, however, larger works may need a qualified professional to come in.

1. Unroll your two pieces of artificial grass, ensuring that the pile is running in the same direction. Fold over each piece by about 300m.
2. To get the perfect seam, cut at least 3 tufts back, ensuring that you don’t trim any grass blades.
3. Either remove the backing on your self-adhesive tape and unroll it down the centre of the join, or roll it out ensuring that the shiny side is down then fix at either end with adhesive.
4. Fold over the grass onto the tape and bring each piece together, ensuring there’s a 2-3mm gap at the seam.
5. Where the pile runs over the edge of the seam, fold over the artificial grass.
6. Apply a small amount of adhesive under the edge of the first section of grass with a mastic gun, then add some to the front edge to stick the second piece.
7. Bring the seam together, ensuring that you don’t get any grass blades stuck. Place a plank with some heavy objects on over the join to ensure that it dries securely.

1. Place a post in the corner of the frame you created with the pegs and string. Measure and mark out 100mm from each side.
2. Dig out this soil to a depth of 700mm (watch out for cables or pipes). You should have a 300 x 300mm hole. Repeat for the other 3 corners.
3. Using a brick bolster, split a concrete block in two. Put a section of the block in each hole.
4. Get a length of post longer than you need and place one in each hole. You can cut it down later.
5. Create props on each post to hold them in place until you’re ready to add a cement mix. Check that they’re level. When you’re happy that they are, secure them in place with a concrete mix, making sure you create a slope in the concrete so that rainwater runs away from each post. When the concrete is set, remove the props.
6. Create a string line around each corner post and find the centre point between each. Place a timber batten at each point, ensuring that they’re not spaced any more than 1500mm apart.

1. Working from the corner where the deck will be at its highest above ground level, measure and mark on the post where the highest part of the frame will be.
2. Measure from the far side of one post to the opposite and cut sections of joist to size. Line up a piece of joist with the mark you made and temporarily secure it. Factor in a 2mm fall for every metre of decking so rainwater can run off.
3. Secure the frame to the other corner post, ensuring it’s at the right level. Do this for every side of the outer frame.
4. Using 100mm coach screws with washers hanging on the end, secure each end of the four sections of frame.
5. Mark out where the centre of the support posts will be and secure all of these posts to the frame, except the centre post.
6. Add your central support joists. These should run in the same direction as the deck boards will run. You’ll need to measure from the inside of the frame on one side to the inside of the frame on the opposite side. Attach the joist in the same way as you did for the other posts. Repeat so the centre post is in between two sections of frame and secure the posts with concrete.
7. Trim down all the posts to the correct height using a saw.
8. Add your weed-control fabric and weigh down with gravel across the entire area.

1. Measure 400mm from the centre of the outer frame and mark a line. This will be where the first joist is positioned. Repeat at 400mm intervals down the length of the frame – if the last one will be more than 400mm, add another joist to create enough support.
2. Attach a joist hanger to each end of the joist.
3. Place the joist in position so the centre lines up with the 400mm spacer mark.
4. Secure using external grade screws once you’re happy that the joist is flush with the frame.

How To Plan A Landscape Garden

If you’ve decided to go for a landscape garden, this might imply putting in new gardens entirely or probably just coming up with a planting plan for the current year. However, because you want a beautiful landscape garden doesn’t mean you can just go out, get a couple of plants and decide to plant them anywhere that looks good to you once you get home.

For a much better landscape garden, doing some proper landscape garden planning can go a long way to help you get the results you desire. So how do you plan a landscape garden?

• Set Goals

The first step is to determine how you want the garden to feel and look, how it’s going to be used or what’s going to be used for as well as how you’ll work to boost the small ecosystem.

• Site Plan

Identify what you already have on the site like the plants, paths, gardens etc, and draw them out perhaps on a graph paper. Once done, you can make some photocopies and start playing with different ideas.

• Site Analysis

Carry out an in depth site analysis to identify the areas that’s sunny and shady areas as well as the ones in between. This way, you can figure out the best place to put the plants and other items.

• Functional Diagrams

This is stage at which you go through both the site plan as well as site analysis and start to identify the right spots to position the landscape garden’s items.

• Planting Plan

Here, you’ll decide which plants you’ll like to use on your landscape garden while also identifying what plant goes where. You’ll have to draw them at size close to what they’ll grow to become, so as to ensure there’s sufficient space for them once they grow big and tall.