Find a Landscaper you can trust in Monmouth.

Chances are at some point you’d probably given a though about how steps would fit in perfectly in your garden, except of course, your yard and garden is flat. Adding steps and gardens makes it a lot easier to get around your yard while also enhancing its curb appeal. In order to avoid the cost of hiring a professional to get the task done, you might be tempted to make it a DIY task. However, if you lack the required skill and confidence to pull this off, we’d strongly recommend you call in a professional so as to avoid costly errors. In this post, we’re going to take you through the garden steps building process. Let’s take a look!

1. Measure the vertical height of the slope by marking it with two parallel lines. Once done, proceed by connecting a string line to the slope’s top and hold it in a horizontal way, take a measurement of the flight’s length and breadth. Divide the measurement by 200mm to get the number of steps that’ll be required. Then proceed to divide the number by the height to identify the depth of each step.
2. Working downwards from the flight’s top, dig the step shapes and also dig a shallow trench and install a concrete foundation.
3. Enable the foundation to harden by leaving it for about 48 hours, then install two courses of bricks on the concrete strip and use gravel to backfill.
4. With the help of a trowel, apply mortar to the top of the brickwork. Place the first slab on the mortar bed and press down. Then, make use of a spirit level to make sure that the steps are level.
5. On the back edge of the first tread, you should proceed to build the second rise, backfill and install the slab to form the second tread – just like the previous step. Repeat this process until you’ve gotten to the top of the flight.

Do I Need A Gardener Or Landscaper?

This is a question that’s often asked by most homeowners across the globe. While it’s true that both gardener and landscaper can make your garden a lot more beautiful and pleasing to the eye, it’s also crucial to know the significant difference between the two professions.

So who is a landscaper? We have two types of landscapers: the landscape architect whose job is to design a landscape and a landscape builder whose job is to do the physical requirements of creating a landscape. Both types are very interrelated such that landscape architects can also be landscape builders or have one or more of the other type in same team (as most landscaping building projects will be supervised by a landscape architect).

Now the main difference between a landscaper and a gardener is the type or scope of work they’re qualified to undertake. Generally, landscapers require just one or more types of trade licences to work, meanwhile a gardener may or may not need a trade licence. So who is a gardener?

It’s the job of a gardener to come in and maintain the landscape garden once the landscape has successfully built the outdoor area. In other words, it’s part of a gardener’s services to prune plants, mow the lawns, do the weeding, fertilize your soil and much more. It’s not their job to construct a large retaining wall or a gazebo. And you can also be sure they won’t appear with a backhoe ready to sculpt your landscape.

Overall, deciding who to choose between a gardener and a landscape depends on the type or scope of work that’s required. With the aforementioned differences, you should be able to easily determine who to call when in need of a landscaping or gardening service.

It’s a good idea to talk to your neighbours before you start any work to avoid confusion along the way. But if the fence is definitely your responsibility and on your property, there’s no legal obligation to notify them. It’s also a myth that you need to erect a fence with the flush side without posts facing your neighbour’s property.

1. Place a post in the corner of the frame you created with the pegs and string. Measure and mark out 100mm from each side.
2. Dig out this soil to a depth of 700mm (watch out for cables or pipes). You should have a 300 x 300mm hole. Repeat for the other 3 corners.
3. Using a brick bolster, split a concrete block in two. Put a section of the block in each hole.
4. Get a length of post longer than you need and place one in each hole. You can cut it down later.
5. Create props on each post to hold them in place until you’re ready to add a cement mix. Check that they’re level. When you’re happy that they are, secure them in place with a concrete mix, making sure you create a slope in the concrete so that rainwater runs away from each post. When the concrete is set, remove the props.
6. Create a string line around each corner post and find the centre point between each. Place a timber batten at each point, ensuring that they’re not spaced any more than 1500mm apart.

1. Working from the corner where the deck will be at its highest above ground level, measure and mark on the post where the highest part of the frame will be.
2. Measure from the far side of one post to the opposite and cut sections of joist to size. Line up a piece of joist with the mark you made and temporarily secure it. Factor in a 2mm fall for every metre of decking so rainwater can run off.
3. Secure the frame to the other corner post, ensuring it’s at the right level. Do this for every side of the outer frame.
4. Using 100mm coach screws with washers hanging on the end, secure each end of the four sections of frame.
5. Mark out where the centre of the support posts will be and secure all of these posts to the frame, except the centre post.
6. Add your central support joists. These should run in the same direction as the deck boards will run. You’ll need to measure from the inside of the frame on one side to the inside of the frame on the opposite side. Attach the joist in the same way as you did for the other posts. Repeat so the centre post is in between two sections of frame and secure the posts with concrete.
7. Trim down all the posts to the correct height using a saw.
8. Add your weed-control fabric and weigh down with gravel across the entire area.

1. Measure 400mm from the centre of the outer frame and mark a line. This will be where the first joist is positioned. Repeat at 400mm intervals down the length of the frame – if the last one will be more than 400mm, add another joist to create enough support.
2. Attach a joist hanger to each end of the joist.
3. Place the joist in position so the centre lines up with the 400mm spacer mark.
4. Secure using external grade screws once you’re happy that the joist is flush with the frame.

Properly installed wooden decking will not need a lot of maintenance. Most manufacturers recommend regularly brushing leaves and dirt off the deck, and a yearly cleaning and staining procedure. This will keep the wood in the best condition. Fluids and treatments are readily available from all DIY shops and stores.

The best way to build a fence depends on what style it is, as different types have different components. However, fencing made up of posts and panels is pretty common. To put this up, you’ll need to start by measuring out and digging holes for your fence posts. Then you’ll need to fit the panels between them and use concrete to secure the posts in the ground.