Find a Landscaper you can trust in Inverurie.

• Paving slabs – old or cheap ones are fine
• Timber for the frame and legs
• Type 1 MOT hardcore

1. Mark out the area as we explain in ‘How to lay decking’. Then, dig to 200mm below where you want to surface of the decking to be.
2. Add a 50mm layer of hardcore and make sure it’s compact.
3. Build the decking sub-frame as we describe in ‘How to build a deck frame’.
4. Lay out paving slabs along the edges and in the centre of the area. This will help to spread the weight of the decking.
5. Set the decking frame on the slabs, checking for high or low points and adding off-cuts of timber where needed. Don’t forget to sand and seal these off-cuts with decking preservative.
6. Add your joists and then the deck boards, leaving the recommended gaps of expansion of between 5-8mm.

Driveway surfacing materials like concrete, asphalt and clay brick usually crack because they’ve been exposed to extreme temperatures or put under high pressure. It’s important to repair driveway cracks before they get worse and cause damage to vehicles and perhaps others to trip on raised cracks.

1. If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
2. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
3. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
4. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
5. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

• Tongue and groove timber boards
• Boards for the ledges and braces, at least 20mm thick
• Nails
• Hammer
• Saws, including a circular saw
• Chisel
• Mallet

1. Cut your boards to size If you can’t buy boards at the right height and width for your door, cut the boards to length using a circular saw. Don’t forget to sand and treat any cut ends with timber preservative. Lay out the boards in the best arrangement for your shed door, with the inside of the door facing up.
2. Arrange the ledges and braces On most shed doors, you’ll probably need 3 boards across the back of the door to form the ledges. The ledges keep the door straight and keep the boards of the door together. The braces are the parts of the door that slope down to form a ‘Z’ shape between the ledges. Ensure that the braces are sloped up from the bottom and middle hinge to stop the door from sagging as the timber expands and contracts in the weather. Once you’re happy with the arrangement, mark the spots on the boards where they will meet and cut out of the housings using a chisel and mallet.
3. Put the door together Use clamps to pull the boards together and hold the ledges and braces in place. Nail from the front of the door through the boards and ledges to fix them. Secure the ledges and braces with screws; you may want to pre-drill and countersink holes to prevent the wood from splitting. Remember to treat them with preservative if you do.
4. Fix the shed door hinges Make sure you measure carefully before attaching the hinges, ensuring you know where the pin sits in relation to where the door opens.
5. Treat the door and add locks and handles Apply some wood oil, like linseed or teak oil, to help prevent water damage. Then add locks or handles to your shed to help keep it secure.
If you’d rather leave it to the professionals, there are plenty of specialists that will be able to make a shed door for you, or even put up an entire shed.

Scarification is the name given to the process where you remove excess thatch and moss from your lawn to encourage it to grow and look healthy. Although it sounds difficult, it’s actually pretty easy – simply grab a sturdy rake and apply moderate pressure to rake out moss, thatch and dead grass. Then collect it up and add to your compost heap if you have one. You can also use a petrol or electric rake, but you just want to tease out the moss and thatch. Don’t be tempted to go deep into the grass, as this could damage your lawn. So when should you scarify your lawn? The experts say that the best time is in the autumn, when the grass is actively growing and it’s not too hot, cold or dry. Most of summer’s weed seeds will have gone, so you won’t encourage weeds to grow in the raked-up soil. This soil also makes an ideal seed bed for over seeding with new grass seed, so that’s why you don’t want to get weeds in there as well. However, you may also carry out light scarification in the spring – usually around April. Make sure you don’t go too far though – as you will end up with a rather disfigured lawn if you scarify too heavily and the dryness of summer stops the lawn from recovering. It’s also best to scarify your lawn in the spring if the following apply:

• If you couldn’t do it the previous autumn – if you keep putting it off, you might end up with extreme moss and weed growth
• If your lawn is shaded – these areas will thin over winter and start to thicken from spring onwards, so if you scarify in the autumn you’ll make your lawn even thinner.
• If your lawn is under trees – pair the shade from the trees with the fall of leaves in the autumn and your grass won’t be healthy, but in the spring the trees are bare, allowing lots of light onto your lawn to help it grow.

Everyone wants a good-looking lawn! If you’re wondering the best time to scarify your lawn, then you’ve come to the right place! In this post, we’re going to consider this in order to help you make the best-informed decision possible. Let’s take a look!

The short and simple answer to this question is when your grass is actively growing. This is the best time to scarify a lawn as it enables it to recover faster once it has been scarified. What’s more? The conditions also have to be appropriate as extreme weather condition, be it too cold, too warm, too dry or too hot, will hinder the quick and proper recovery of your lawn. It’s also important to take note that scarifying of a lawn is going to leave the soil exposed which makes way for weed and other unwanted plants to grow.

During the year, there are two different times which tends to provide the most ideal conditions to scarify a lawn. The first of these periods is late March or April when the spring is in the air and your grass receives all the warmth and moisture it needs to thrive. It’s also advisable not to wait till too late in the spring as right after this period comes the heat and dryness of summer. Furthermore, the lawn shouldn’t be scarified too heavily during the spring as summer usually comes with weed seeds which means your grass won’t recover fast enough and weeds will quickly make way for themselves.

If you wish to scarify your lawn heavily, then the perfect time to do this would be in September or October – during autumn. During this period, the summer weed seeds would be gone and the grass will grow properly.

What Is Landscape Gardening?

Landscape gardening is basically the art of setting out grounds or planting of ornamental plants so that a picturesque effect is created. In other words, it can be seen as the beautification or decoration of a portion of land to generate a naturalistic effect in a limited space. However, it should also be noted that landscape gardening meant to beautify places, but also important and very functional as our surroundings make a whole lot of contribution to the quality of our lives. Landscape is a word that’s not only used to qualify an beautiful scenery, but also stands for a great historical records of natural features created by human activities over time. So what are the general principles of landscaping?

• The right landscape garden should express some thought or feeling, just like a good landscape painting. The expression can be bold, quiet, retired and more.

• The landscape garden area should be divided into various sections with a plan for each individual area. The whole plan should be actualized in such a way that an observer or visitor can imagine the entire plan and purpose without having to analyse each parts.

• It’s of great importance to combine both beauty and utility effectively.

• The design’s simplicity should be emphasized while executing the plan.

• The garden and building should perfect blend with each other in such a way that they could be seen as one rather than the landscape garden stopping abruptly in front of the building. The view of the garden from the building’s door or window should offer an breath taking scenery. In short, every part of the landscape should be planned so that every visitor will have a surprising effect when seen.

• The ideal landscape should not be too tight and should possess an open space.

• Do not overcrowd the plants and objects.