Find an Insulation Installer you can trust in Haverhill.

Do you know about 25 percent of heat that escapes from an uninsulated house are lost through the roof? Fortunately, roof insulation is something that can done by all DIYers irrespective of their experience levels. However, if you happen to lack the confidence necessary to pull off this, then it’s strongly recommended that you hire the services of a professional who can guarantee the best results and also save you time and money that could arise from potential cost mistakes. Let’s take a look!

• Clear out all clutter. This involves taking out all the rubbish and clutter from the loft. In order to work effectively, you’ll need a totally clear and empty loft space.
• Ensure that there’s sufficient insulation. The importance of a good ventilation cannot be overstated. Poor ventilation will result in forming of condensation and this condensation can make the roof timbers rot and compromise the structural integrity of the entire roof. If there are no roof windows which is the easiest way to provide a loft ventilation, the next best option would be to follow the loft floor along to the point where the roof comes down to meet it. There should be a gap at this point, also referred to as the eaves, between the outside wall and the underside of the roof.
• Measure your loft area. Take a measurement of the loft space in order to calculate the amount of insulation as well as the type you need. If you’re not sure, always get more that it’s required as skimming on the amount you use will only back fire in form of increased energy costs
• Check for water pipes.

To get started, simply make sure all cracks and gaps in the ceiling are filled using a standard filler or decorator caulk. Once done, clean the gaps in the joists and even to the point of hovering all the dust up. Finally,check for the hazards that can cause you problems before laying the loft insulation.

With the title of this blog, do not be deceived into thinking the purpose is to encourage you to install an external insulation by yourself. Even as a competent DIYer, it’s not advisable to buy a couple of materials and start slapping it into the wall hoping for the best outcome. External insulation is by no means a DIY job and without the proper training and experience, it can easily turn out disastrous resulting in loss of time, effort and money in such a valuable project. This blog, however, will give you a great insight on how the installation process works and help maximize knowledge ensuring you do not spend more than necessary.

External Insulation Installation

lRender Test

• This is done to ensure the existing render is good enough for insulation support.

• If positive, the insulation can be applied directly onto it.

• If negative, ensure removal of the old render before fitting the insulation.

lPipework Adjustment & Removal

• Remove all pipework prior to insulation fitting

• Install temporary downpipes to ensure water is not wasted and everything continue to function normally during the insulation fitting process.

lWindow Protection

• Protect the window with a protective layer or film.

lStarter Track Fitting

• Determine level you want the insulation to start (height).

• Fit the aluminium start track or carrier tray at the identified level.

lInsulation Boards Fitting

• Apply a layer of adhesive to the board and glue them to the wall in a staggered pattern.

• Cut to fit round all obstructions and windows.

• File off the edge of the board where necessary using a rasp upon successful fitting of the boards

lMechanical Fixing Inclusion

• Hammer around 10 fixings per square metre into the board.

• This is to secure the insulation boards.

lBeading Fitting

• Add corner beads and stop beads to ensure the insulation is secure and to prevent it from making contact with other materials.

lReinforcing Mesh & Render Addition

• Apply two layers of strengthening properties and between the two layers of render, include a fibre glass mesh.

lPrimer Application

• Paint on the primer

lFinal Render Application

• Choose your most preferred texture and colour as this will be the last coating of the installation process.

lPipework Re-installation

• Re-install all detached pipework at the start of the installation process.

Over the years there has been an increase in the recommended thickness of loft insulation by the government. Obviously, the reason behind this is pretty simply - the thicker the layer of your loft insulation the bigger your savings. The UK government is very keen to every house in the country to have loft insulation fitted where possible as it helps to minimize the heating demands of these properties. Households get to benefit from loft insulation in so many ways which includes reduced energy energy bills as well as having a home that stays at a more comfortable temperature for longer.

Generally, for the government energy efficiency is crucial as it implies that the highest demand ( which is usually the time of the day when gas or electricity use is at its peak ) reduces, since each building requires slightly less energy. Overall, that ultimately implies that new power plants don’t have to be built which is some nice cost savings for the government.

In the 1980’s, any thickness of loft insulation from 25 mm to 50 mm was considered the standard. But then, building regulations stated that homes should have as much as 100 mm of loft insulation. Over time, this gradually increased to 270mm for new builds and also recommended for other properties, although not essential. As a result of this, there’s always a need to check how much insulation you currently have in your loft before you decide to purchase more. You may discover that you already have something within the range of 20 mm to 200 mm up there and knowing this and the insulation values will assist in determining how much more you’ll need to purchase, if any at all. You should also note that some modern materials can offer the same thermal insulation whilst not being as thick.

With the numerous benefits that comes with the installation of an external wall insulation in a building, it’s also important to find out whether it’s also safe before proceeding to fit one in your home. Firstly, to ensure that external wall insulation systems are safe, they must be BBA approved, which means they’ve been subjected to a thorough testing by the British Board of Agrement and therefore, suitable for use in UK homes.

Given the fact that cladding materials have recently generated a lot of debate and negative press about how reliable some particular materials are, questions are being asked of the safety and reliability of external wall insulation. However we must clarify that, although external wall insulation can be classified under cladding, it is very different to rainscreen cladding - which caused the Grenfell fire tragedy.

External wall insulation is completely safe. However, when it comes to fire, the safety of your system depends largely on the insulation type in question. The safest type of insulation you can have installed is the Rockwool insulation boards which are rated as Euroclass A1 non-combustible. The board is specially designed in such a way that it contains fire - preventing it from reaching the other areas of the building. They also do not produce harmful emission or smoke when impacted by fire.

Meanwhile, the Wood Fibre, is also a great insulation which is known to char and not burn. Contrary to many beliefs, it actually burns slowly creating this charring effect which produces an oxygen barrier that helps reduce the spread of fire.

To make your system safer, you can also make use of Fibreglass Mesh for reinforcement. It helps to improve the strength of the tensile which promotes the security of the boards attached to the wall.

The answer is yes! Houses whose external walls have been insulated are more valuable than their uninsulated counterparts. And not only does it add to the value of a home, but also significantly reduces the amount of electricity consumption. This is a major turn on for potential investors which implies a greater demand and ultimately, a higher price. The real estate market is a very dynamic one which can be hard to predict at any particular time. The frequent changes in price are usually down to factors beyond the owners’ control, but if you’re looking to put up your house for sale in the near future, it would be a wise decision to consider ways in which you can increase its value. While renovating each room can be on the expensive side, a great solution would be insulate the external walls.

An insulated house is one that is well secured against the harmful impact of extremely high or low temperature, humidity and other atmospheric factors. Hence, the reason why a house with external wall insulation has a greater value which you would not want to miss out on. What’s more? You’ll get a great thermal insulation with the top notch materials like foamed polystyrene, high quality renders, mineral wool or polyurethane.

With an external wall insulation, you know the transaction will always be favourable on both ends. You get to smile to the bank, while the buyer also gets to enjoy great value for every penny spent. To employ the services of a reliable external wall insulation expert, simply conduct an in depth research from family and friends, online and other sources. Go through their online reviews and ask questions to become more familiar with the process and its value-adding potentials.

This depends on the amount of insulation already present in your property. However, adding insulation has been proven to improve the energy efficiency of your home and decrease your heating bills, this is more obvious in older properties or where single glazing is still in situ.

Insulating a cavity wall should not affect the damp proofing of the wall. All insulation approved for use in cavity walls has been tested to ensure that it does not allow damp to pass through the wall. Some walls which receive a lot of wind driven rain are unsuitable for cavity wall insulation.

In general, you won’t need planning permission to install soundproofing. If you are installing soundproofing against a shared wall, you will usually need to follow the rules and restrictions set out in the Party Wall Act. In listed buildings and conservation areas, there may be extra restrictions on soundproofing.